IOptron GEM45 Bedienungsanleitung

iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com

Quick Start Guide

GEM45™ German Equatorial Mount

Models: GEM45 (#7603A), GEM45EC (#7603ECA) and GEM45G (#7603AG)

PACKAGE CONTENTS1

Mount head –with iPolarTM electronic Polar Scope (#7603A & #7603ECA), and iGuiderTM guiding system (#7603AG)

Hand Controller (HC) –Go2Nova® 8407+

Counterweight –11 lbs (5 kg)

Stainless steel counterweight shaft

GPS module

RJ11 coiled cables, x2

USB cable

AC adapter –100-240V (DC output 12V/5A)

Alignment peg

Heavy duty tripod and accessory tray

Hard case (for 7603ECA, optional for 7603A, 7603AG)

Quick Start Guide (this document)

ONLINE RESOURCES (at www.iOptron.com, under Support)

User’s Manual

Hand controller and mount firmware upgrades (check online for the latest version)

ASCOM and Commander for computer control

1The design, contents and packaging may change from time to time without notice.

iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com

STOP!!! Carefully read this Guide BEFORE setting up and using the equipment!

Worm/gear damages due to improper uses are not covered by warranty.

WARNING: Never disengage Gear Switches without holding the mount firmly! Fail to do so

may result in personal injuries and/or equipment damages.

1. Remove mount head from package: The mount

head is shipped with the R.A. Gear Switch unlocked to

protect the worm/gear system. Turn the Gear Switch

90° clockwise to lock the R.A. gear system before

removing it from the box.

2. Set up Tripod: The tripod top is 120 mm in diameter

with 2x M6 holes 103 mm apart for mounting. Two

additional M6 holes are for the Alignment Peg (the

one right next to one of the legs is for uses at high

latitudes; the other one is for uses at low latitudes).

Thread the Alignment Peg into the correct M6 hole.

Insert the Accessory Tray through the center rod and

secure the setup by tightening Locking Knob from

underneath.

Set up Mount Head: Retract the 2x Azimuth (Azi)

Adjustment Screws from both sides to leave ample

space for the alignment peg to fit in between the 2

Azi Adjustment Screws. Remove the 2x Azi Locking

Screws, with washers, from the mount base. Secure

the mount head by tightening the Azi Locking Screws

into the M6 holes on the tripod. An Allen wrench is

included for convenience.

Level the mount by adjusting the tripod legs. Use the

build-in bubble Level Indicator or an external leveler

for this purpose.

3. Adjust Latitude: Without any payload, slightly loosen

the 4x Latitude Locking Screws. Use the Latitude

Adjustment Knob to set the correct latitude value, as

displayed in the Latitude Mark Window. Insert the

Allen wrench into the Latitude Adjustment Knob for

more turning torque.

Two latitude ranges, 14~44° and 36~68°, can be set

up for the mount head. To change the latitude range

Allen wrench

Lat. Lock Screw

Lat. Mark

Azi. Adj. Screw

Lat. Adj. Knob

iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com

from one to the other, both the Latitude Position Bolt

and the Latitude Locking Screws need to be moved to

the correct locations (see photos below).

Loosen the Latitude Locking Screws just enough to

adjust the latitude setting to 40°. Move the Latitude

Locking Screws with washers (one on each side) to

the new locations revealed, do not tighten them just

yet.

Unthread and remove the Position Bolt to its new

location. Adjust the Latitude Adjustment Knob while

holding the brass eyebolt until it lines up with the

Position Bolt. Secure the Latitude Position Bolt.

4. Install Counterweight (CW) Shaft: Thread the CW

shaft into the CW shaft mounting holes.

5. Install Counterweight(s): Before putting on CW,

make sure the mount is at its zero position, i.e., CW

shaft points to the ground. Disengage the R.A. Gear

Switch to set the R.A. axis free before loading the

CW. Remove the CW Safety Cap at the end of CW

Shaft. Glide the CW over the shaft. Tighten the CW

Locking Screw to hold the CW in place. Place the

Safety Cap back onto the shaft. Move the CW to the

bottom of the shaft and tighten the CW locking

Screw.

You may need more CW for heavier payloads, or a

smaller CW for lighter scopes.

6. Install Telescope:

A GEM45 is equipped with a 6” Vixen/Losmandy-D

dual saddle. It can receive either a Vixen or a

Losmandy-D plate. A GEM45AG has an iGuiderTM

guiding system on the dovetail saddle.

7. Balancing the Payload: After attaching the scope and

accessories, the mount head assembly must be

balanced in both DEC and RA axes to ensure

minimum stresses on the mount driving mechanism.

CAUTION: The telescope may swing freely when the

R.A. or DEC Gear Switch is disengaged. Always hold

on to the mount and/or telescope assembly before

releasing the Gear Switches to prevent it from

swinging, which can cause personal injuries and/or

equipment damages.

Set the mount at Zero Position. Disengage both RA

and DEC gear switches and move the mount to

horizontal position to check balance. Return to Zero

Position for balance adjustment. Balance the DEC axis

by moving the scope with accessories back and forth

Position Bolt

iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com

in the mount saddle or within the scope mounting

rings. Balance the assembly in R.A. axis by moving

CW along its shaft. Repeat the process until both DEC

and RA axes are balanced.

CAUTION: The balancing process MUST be done with

Gear Switch at the total ddisengaged position!

Otherwise it might damage the worm system.

Return the mount to Zero Position after balancing

and engage gear switches.

8. Connecting Cables:

Plug in included 12V/5A DC power supply to the

DC12V 5A socket, which is located at the end of the

RA axis.

Connect the Go2Nova®8407 Hand Controller to the

HBX port on the mount main board.

Plug GPS module into the iPORT with a coiled cable.

When powering on, GPS ON sign should be displayed

at the upper right corner of the hand controller. You

may disconnect the GPS module after it picks up

satellites signals and displays GPS OK. (It takes about

1 to 2 minutes in normal conditions).

9. Polar Alignment: GEM45 mounts are equipped with

an iPolarTM electronic polar scope. To perform polar

alignment, please refer to GEM45 User’s Manual, or

iPolar Operation Manual from iOptron’s website. The

steps are outlined below:

Download and install iPolar Software (first

time use)

Connect a USB cable between the USB2.0

port at the end of the RA axis and a computer

USB port

Calibrate the iPolar camera center (first time

use)

Click Connect and start polar alignment by

following on screen instructions

For the mount without polar scope, please refer to

full manual for Bright Star Alignment, or use

software to assist alignment.

10. Manual Operation: The mount can now be used to

observe astronomical objects with the HC. Use arrow

keys (►, ◄, ▼,and ▲) to point the telescope to

desired objects. Use the number keys to change the

slewing speed. Press the STOP/0 button to start or

stop tracking.

11. Set Controller: Press the MENU button; then Settings

=> Set Time and Site.

Before GPS picks up signals (before displaying GPS

OK), check for Daylight Saving Time using arrow key

to toggle between Yand N. Enter the time zone

offset to the UTC; for examples:

Boston is “UTC -300 minutes”

Los Angeles is “UTC -480 minutes”

Rome is “UTC +060 minutes”

Sydney is “UTC +600 minutes”

Waiting for the mount to pick up the GPS (you’ll hear

beep). If the GPS is “OK’d” during setup, just power

cycle the mount. Double check the HC display and it

should show correct local time.

iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com

[TIPS: All time zones in N. America are “UTC -XXX

minutes”. Latitude and longitude coordinates can be

obtained from GPS-equipped devices (navigator,

phone), or from internet and entered manually, in

case GPS cannot receive enough satellites signals or

GPS malfunctions. “W/E” = western/eastern

hemisphere; “N/S” = northern/southern hemisphere.

Use arrow and number keys to enter location and

time information.]

12. Set Zero Position: The Set Zero Position command

registers the current position as zero position. So

before registering, the mount should be physically set

at Zero Position either manually or slewed by hand

controller. The Zero Position is defined as the

telescope being on top of the mount head and

pointing to North Pole, with CW shaft pointing to the

ground. To register, press MENU => Zero Position =>

Set Zero Position. Press ENTER to confirm. One can

also use MENU => Zero Position => Search Zero

Position to set the zero Position.

13. One Star Alignment: Perform One Star Align to

correct the Zero Position discrepancy and improve

GOTO accuracy. Refer to User’s Manual for more

details about improving GOTO accuracy.

14. Go to an Object: The mount is now ready for GOTO

and tracking targets. Press MENU, select and ENTER

Select and Slew. Select a category (e.g., Solar

System), then select an object of interest (e.g.,

Moon). Press ENTER and the telescope will slew to

the object and automatically start tracking.

15. Sync to Target: If the object is not in the center of

the eyepiece, use this function to center and

synchronize the object to improve local GOTO

accuracy. Press MENU and select and ENTER Sync to

Target. Follow the on-screen instruction to perform

the sync.

[TIP: After slewing to an object, a list of nearby bright

object(s) can be displayed by pressing the ?button.]

16. Put the mount back into the package/carrying case:

It is recommended to return the mount to Zero

Position at the end of the observing session. Lay the

mount into the carrying case. Disengage the gear

system for transportation.

Please contact [email protected]om for technical

support.

V2.0

iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com

IOPTRON TWO YEAR TELESCOPE, MOUNT, AND CONTROLLER WARRANTY

A. iOptron warrants your telescope, mount, or controller to be free from defects in materials and workmanship for two years. iOptron will

repair or replace such product or part which, upon inspection by iOptron, is found to be defective in materials or workmanship. As a

condition to the obligation of iOptron to repair or replace such product, the product must be returned to iOptron together with proof-of-

purchase satisfactory to iOptron.

B. The Proper Return Merchant Authorization Number must be obtained from iOptron in advance of return. Contact iOptron at

1.781.569.0200 or s[email protected] to receive the RMA number to be displayed on the outside of your shipping container.

All returns must be accompanied by a written statement stating the name, address, and daytime telephone number of the owner,

together with a brief description of any claimed defects. Parts or product for which replacement is made shall become the property of

iOptron.

The customer shall be responsible for all costs, such as transportation, insurance and fees, both to and from the factory of iOptron, and

shall be required to prepay such costs.

iOptron shall use reasonable efforts to repair or replace any telescope, mount, or controller covered by this warranty within thirty days of

receipt. In the event repair or replacement shall require more than thirty days, iOptron shall notify the customer accordingly. iOptron

reserves the right to replace any product which has been discontinued from its product line with a new product of comparable value and

function.

This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function, or

subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or deterioration due to normal wear is not

covered by this warranty.

IOPTRON DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF FITNESS FOR A

PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HERE. THE SOLE OBLIGATION OF IOPTRON UNDER THIS LIMITED

WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH

HERE. IOPTRON EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL

DAMAGES WHICH MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO USE

ANY IOPTRON PRODUCT. ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED SHALL BE LIMITED

IN DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL RETAIL PURCHASE.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied

warranty lasts, so the above limitations and exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

iOptron reserves the right to modify or discontinue, without prior notice to you, any model or style telescope.

If warranty problems arise, or if you need assistance in using your telescope, mount, or controller contact:

iOptron Corporation

Customer Service Department

6F Gill Street

Woburn, MA 01801

www.ioptron.com

[email protected]

Tel. (781)569-0200

Fax. (781)935-2860

Monday-Friday 9AM-5PM EST

NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an authorized iOptron dealer in

the U.S.A. or Canada or directly from iOptron. Warranty outside the U.S.A. and Canada is valid only to customers who purchased from

an iOptron Distributor or Authorized iOptron Dealer in the specific country. Please contact them for any warranty.

Andere Handbücher für GEM45

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere iOptron Rack & Stand Handbücher

iOptron

iOptron MiniPier Bedienungsanleitung

iOptron

iOptron NI63385 Bedienungsanleitung

iOptron

iOptron HEM27 Bedienungsanleitung

iOptron

iOptron CEM25 Bedienungsanleitung

iOptron

iOptron iEQ30 Pro 3000E Bedienungsanleitung

iOptron

iOptron CEM40 Bedienungsanleitung

iOptron

iOptron CEM40EC Bedienungsanleitung

iOptron

iOptron CEM120 Bedienungsanleitung

iOptron

iOptron SkyHunter Portable EQ/AZ GoTo System Bedienungsanleitung

iOptron

iOptron GEM45G Bedienungsanleitung

iOptron

iOptron CEM25P Bedienungsanleitung

iOptron

iOptron C70A Series Bedienungsanleitung

iOptron

iOptron CEM40G Bedienungsanleitung

iOptron

iOptron MiniTower GOTO Bedienungsanleitung

iOptron

iOptron HEM27 Bedienungsanleitung

iOptron

iOptron CEM70 Bedienungsanleitung

iOptron

iOptron HAE29 Bedienungsanleitung

iOptron

iOptron SmartStar iEQ45 Bedienungsanleitung

iOptron

iOptron iEQ30 Pro 3000E Bedienungsanleitung

iOptron

iOptron SmartStar CubePro GOTO AltAz Bedienungsanleitung

iOptron

iOptron CEM40 Bedienungsanleitung

iOptron

iOptron SkyGuide 3550A Bedienungsanleitung

iOptron

iOptron GEM45EC Bedienungsanleitung

iOptron

iOptron 7100P Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

iOptron GEM45 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken