IOptron Pier Bedienungsanleitung

iOptron®Pier

Instruction Manual

Product #8030, #8033

iOptron®Pier is designed for iOptron GOTO

mounts, which includes iEQ45, iEQ30,

MiniTower, MiniTower II, or MiniTower Pro

mount.

Parts included1:

1. 1x Pier Tube

2. 1x Pier Base with three (3) Pier Legs

preinstalled

3. iEQ45 Center Stud and Alignment Peg

(preinstalled)

4. 1x M12 Center Bolt with turning lever for

MiniTower/MiniTower Pro mounting

5. 1x iEQ30 Alignment Peg

Specifications:

#8030 48 inch tall pier:

yPier diameter: 5.7" (144mm) with 6"

(150mm) Flange plates

yPier height: 40” (1016mm)

yStanding height:48” (1220 mm)

yLeg length: 22.5” (570mm)

yNet weight: 25 lbs (11.3 kg)

yPayload: 132 lbs (60kg)

#8033 42 inch tall pier:

yPier diameter: 5.7" (144mm) with 6"

(150mm) Flange plates

yPier height: 34” (840mm)

yStanding height:42” (1066mm)

yLeg length: 22.5” (570mm)

yNet weight: 23 lbs (10.4 kg)

yPayload: 132 lbs (60kg)

Pier Setup:

iOptron pier comes in a single box. For #8030 (48”

pier), all the parts are stored inside the pier tube, as

shown in Fig.1. For #8033 (42” pier), three (3) poll

rods may slide into the pier tube, but not as secure

as #8030.

Figure 1

1Parts included may be different from the list and photos.

Unthread the Pier Locking Screw (This screw is

only used for pier storage). Separate the Pier

Base with Legs from the Pier Tube. Remove the

Pull Rods from inside the pier.

Figure 2

Figure 3

Move the Pier Foot from the end to the side.

Figure 4

Spread the Pier Leg. Put the Pier Tube onto the

Pier Base, with Pier Alignment Slot aligned over the

Alignment Tab on the Pier Base.

Pull Rods

Pier Foot

(Storage

Position)

Pier Base

Pier Tube

Pier Locking

Screw

Figure 5

Adjust the length of the three Pull Rods. Hook one

end of a Pull Rod onto a bolt located on the Pier

Leg and the other Pull Rod end onto the mounting

beam inside the Pier Tube. Evenly tighten the Pull

Rods. Make sure there is no gap between the Pier

Base and Pier Tube.

Figure 6

There are three sets of holes/threads on top flange

of the pier. They are designed for mounting an

iEQ45, an iEQ30 or a MiniTower series mount, as

indicated in Figure 7.

Figure 7 Pier with Alignment Peg and Center Stud

for iEQ45

To install an iEQ45 mount onto the pier, just simply

face the alignment peg north (if you are located in

northern hemisphere), and install the iEQ45 mount.

Tighten 3 Azimuth Locking Screws.

Figure 8 iEQ45 on a pier

To install an iEQ30 mount onto the pier, remove the

iEQ45 alignment peg. Thread an iEQ30 alignment

peg into the middle threaded hole located on inner

circle. Then face the alignment peg north (if you are

Tighten evenly

Adjustable Feet

Pier Leg

Pier Base

Align Slot

Align Tab

For iEQ45 Azimuth

Lockin

Screw Alignment

Peg

Center

Stud

located in northern hemisphere), and install the

iEQ30 mount. Tighten 2 Azimuth Locking Screws.

Figure 9 Pier with Alignment Peg and Center Stud

for iEQ30

Figure 10 iEQ30 on a pier

To install a MiniTower series mount (MiniTower,

MiniTower II or MiniTower Pro) onto the pier,

remove the top flange from the Pier Tube by

remove three mounting screws. Remove iEQ

Center Stud and Alignment Peg. Insert the

MiniTower Center Bolt through the center hole.

Install the Turning Lever. Mount the Top Flange

back to the Pier Tube.

Figure 11 Pier with MiniTower Center Bolt

Install 3 MiniTower level adjustment screws and

threaded in about half of the threads. Put the

MiniTower on to it. Level it. Thread the MiniTower

Center Bolt into the MiniTower and tighten it. Make

sure the mount is leveled while rotating the mount.

Figure 12 MiniTower on a Pier

For iEQ30 Azimuth

Lockin

Screw For MiniTower

Levelin

Screws Center Bolt

Dieses Handbuch passt für folgende Modelle

Andere iOptron Rack & Stand Handbücher

iOptron

iOptron CEM40EC Bedienungsanleitung

iOptron

iOptron CEM70G Bedienungsanleitung

iOptron

iOptron SkyHunter Portable EQ/AZ GoTo System Bedienungsanleitung

iOptron

iOptron CEM26 Bedienungsanleitung

iOptron

iOptron GEM28 Bedienungsanleitung

iOptron

iOptron NI63385 Bedienungsanleitung

iOptron

iOptron HAE43 Bedienungsanleitung

iOptron

iOptron CEM120 Bedienungsanleitung

iOptron

iOptron Tri-Pier Bedienungsanleitung

iOptron

iOptron HEM44 Series Bedienungsanleitung

iOptron

iOptron MiniTower GOTO Bedienungsanleitung

iOptron

iOptron HEM27 Bedienungsanleitung

iOptron

iOptron HEM27 Bedienungsanleitung

iOptron

iOptron CEM70EC Bedienungsanleitung

iOptron

iOptron SmartStar iEQ45 Bedienungsanleitung

iOptron

iOptron SkyGuide 3550A Bedienungsanleitung

iOptron

iOptron iEQ30 Pro 3000E Bedienungsanleitung

iOptron

iOptron HAE69B Bedienungsanleitung

iOptron

iOptron GEM45EC Bedienungsanleitung

iOptron

iOptron CEM25P Bedienungsanleitung

iOptron

iOptron SmartStar CubePro GOTO AltAz Bedienungsanleitung

iOptron

iOptron CEM40 Bedienungsanleitung

iOptron

iOptron CEM40 Bedienungsanleitung

iOptron

iOptron CEM40 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

iOptron Pier Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken