IP Camera HLV-1CM Bedienungsanleitung
1/39
User Manual
CMOS 1.3 Mega Pixel
IP Vandal Dome Camera
2/39
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
DO NOT INSERT ANY METALLIC & ELETRIC CONDUCTIVE OBJECT THROUGH
VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED
TO THEIR RESPECTIVE COMPANIES.
3/39
Content
I. PREFACE..................................................................................................................................................... 4
II. PRODUCT SPECIFICATIONS ................................................................................................................. 4
III. PRODUCT INSTALLATION ................................................................................................................ 6
A. MONITOR SETTING..................................................................................................................................... 6
B. HARDWARE INSTALLATION ........................................................................................................................ 7
C. IPASSIGNMENT ....................................................................................................................................... 10
D. INSTALL ACTIVEXCONTROL:................................................................................................................... 13
IV. LIVE VIDEO......................................................................................................................................... 15
V. IP CAMERA CONFIGURATION............................................................................................................ 17
A. SYSTEM ................................................................................................................................................... 18
B. NETWORK ................................................................................................................................................ 21
C. A/V SETTING ........................................................................................................................................... 25
D. EVENT LIST.............................................................................................................................................. 32
VI. NETWORK CONFIGURATION ........................................................................................................ 36
VII. FACTORY DEFAULT .......................................................................................................................... 38
VIII. PACKAGE CONTENTS ...................................................................................................................... 38
APPENDIX I........................................................................................................................................................ 39
4/39
I. Preface
IP Vandal Dome is a professional CMOS Mega Pixel IP Vandal Dome. It has
built-in web server which enables user to view real-time video via IE browser. It
also supports simultaneously MPEG-4&JPEG video compression with CMOS
M-Pixel Sensor which provides smooth and high video quality. The video can be
stored in the SD card, and can be playback remotely.
IP Vandal Dome is an easy-to-use IP Camera which is designed for security
application.
II.Product Specifications
zSupport IP66 (Weatherproof)
zSupport PoE (Power Over Ethernet) – Optional
zIR LED Built-in 12M available
zMechanism IR Cut Filter available
zVandal Proof (Polycarbonate shell withstand impact up to 400 pounds)
zMPEG4/ JPEG compression
zSupports SD card for local recording
z2-way audio
zSupport Cell Phone/PDA/3GPP
zOnline firmware upgrade
Specifications
Hardware
Model HLV-1CM
Image sensor 1/4” CMOS ,1.5 lux
Lens Changeable Vari-focal lens 3.7~12mm
ICR Mechanism IR Cut Filter (Optional)
IR LED Built-in (Optional)LED
IR Distance-12M (Optional)
CPU ARM 9 ,32 bit RISC
SDRAM 64MB
5/39
Flash 8MB
I/O 1 in/ 1 Relay out (COM. & N.O.)
Audio in 1
Audio Out 1
Power over Ethernet
(PoE)
Optional
Power Consumption DC 12V, 490mA
Dimensions 126mm (W) x 126mm (L) x 100mm (D)
Network
Ethernet 10/ 100 Base-T
Network Protocol HTTP, TCP/ IP, SMTP, FTP, PPPoE, DHCP,
DDNS, NTP, UPnP, 3GPP
System
Video Resolution 1280x1024, 640x480, 320x240, 160x120
Video adjust Brightness, Contrast, exposure, sharpness
Dual Streaming Yes
Image snapshot Yes
Full screen monitoring Yes
Compression format MPEG-4/ JPEG
Video bitrate adjust CBR, VBR
Motion Detection Yes, 3 different areas
Triggered action Mail, FTP, Save to SD card
Pre/ Post alarm Yes, configurable
Security Password protection
Firmware upgrade HTTP mode, can be upgraded remotely
Simultaneous
connection
Up to 10
Audio Yes, 2-way
SD card management
Recording trigger Motion Detection, IP check, Network Status (wire
connection only)
Video format AVI, JPEG
Video playback Yes
Delete files Yes
Web browsing requirement
OS Windows 2000, XP, 2003, Microsoft IE 6.0 or
6/39
above
Hardware Suggested Intel-C 2.0G, RAM: 512MB, Graphic card: 64MB
Minimum Intel-C 1.6G, RAM: 256MB, Graphic card: 32MB
III. Product Installation
A. Monitor Setting
i. Right-Click on the desktop. Select “ Properties”.
ii. Change color quality to highest (32bit).
7/39
B. Hardware Installation
i. Connect power adaptor
ii. Connect Ethernet cable to IP Camera
iii. Connect IP Camera to a computer or Local network.
Ｂ-1 I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notifications. It provides the interface to:
1 Digital Input (GND+Alarm) – An alarm input for connecting devices that can toggle
between an open and closed circuit, for example: PIRs, door/window contacts, glass
break detectors, etc. When a signal is received the state changes and the input becomes
active.
1 Relay output (COM +N.O.) – An output to Relay switch, for example: LEDs, Sirens,
etc
Digital Input
Alarm Input
1. GND (Ground) : Initial state is LOW
2. Alarm : Max. 50mA, 12VDC
Relay Output
1. COM: (Common)
2. N.O. (Normally Open): Max. 1A, 24VDC or 0.5A, 125VAC
RCA Line in (Green)
RCA Line Out (Pink)
8/39
B-2 Relay Connection:
Digital Input connection
Relay Output Connection
GND
ALARM
COM
N.O.
ALARM IN
Relay Out
GND
ALARM
COM
GND
ALARM
COM
Door/Window
Contacts
9/39
B-3 Power Over Ethernet PoE – (Optional) 802.3af, 15.4W PoE Switch is recommended
Power over Ethernet (PoE) is a technology that integrates power into a
standard LAN infrastructure. It enables power to be provided to the network
device, such as an IP phone or a network camera, using the same cable as that
used for network connection. It eliminates the need for power outlets at the
camera locations and enables easier application of uninterruptible power
supplies (UPS) to ensure 24 hours a day, 7 days a week operation.
Ethernet
PoE Switch
PoE IP Camera
PoE IP Camera
Ethernet Cable
Ethernet Cable
10/39
C. IP Assignment
i. Use the software, “IP Installer” to assign the IP address of IP Camera.
The software is in the attached software CD.
ii. There are two languages for the IP installer
a. IPInstallerCht.exe：Chinese version
b. IPInstallerEng.exe：English version
iii. There are 3 kinds of IP configuration.
a. Fixed IP (Public IP or Virtual IP)
b. DHCP (Dynamic IP)
c. Dial-up (PPPoE)
iv. Please execute IP Installer
v. For Windows XP SP2 user, the following message box may appear.
Please click “Unblock”.
vi. IP Installer configuration:
Inhaltsverzeichnis
Andere IP Camera Sicherheitskamera Handbücher
