IPC Eagle B1500 Bedienungsanleitung

OPERATIONS MANUAL

& PARTS LIST

B1500, B2000, FM17, FM20

IPC Eagle • 3650 Dodd Rd, Eagan MN 55123 •800.486.2775 •www.ipceagle.com

WHEN THE MACHINE IS DELIVERED

Check the carton carefully for signs of rough handling. Remove the machine from the carton. If the

machine is damaged, notify the carrier IMMEDIATELY and request an inspection. Be sure to keep the

carton, packing inserts, packing lists and carrier’s receipt until the inspector has verified your claim.

IPC’s liability ceases when the carrier picks up the shipment but our customer service staff will be glad to

furnish any information needed in connection with the claim and will expedite repair of the machine.

BEFORE OPERATING THE MACHINE

Read the manual carefully and completely before attempting to operate the unit. This manual has

important information for the use and safe operation of the machine. Keep this manual handy at all times.

This machine will assure years of satisfactory service if operated and maintained according to

recommendations in this manual. If additional information is needed, please contact your local distributor

or write to:

IPC EAGLE

3650 Dodd Rd

Eagan, MN 55123

All information and specifications printed in the manual and parts list are current at the time of printing;

however, because of IPC’s policy of continual product development, we reserve the right to make changes

at any time without notice.

WARRANTY

To protect your investment, promptly fill in the required information on the warranty card that comes with

the unit and mail it back to IPC.

WARNING

To reduce the risk of fire, electric shock, or injury:

•Do not operate the machine unless trained and authorized.

•Do not leave the machine when plugged in. Unplug from the outlet when not in use, before servicing,

and when changing the brushes or pads.

•Use indoors only.

•Do not allow to be used as a toy. Close attention is necessary when used by or near children.

•Do not bypass or defeat the safety “lock-out lever.”

•The machine was designed for use as per instruction and recommendations written in this manual. Any

deviation from its proper use or purpose and the consequential damage that may occur is the sole

responsibility of the end user.

•Do not use with damaged cord or plug. If the machine is not working as it should, or it has been

dropped, damaged, left outdoors or dropped into water, return it to an authorized service center.

WARNING

•Do not pull or carry by cord, use cord as handle, close a door on the cord or pull cord around sharp

edges or corners. Do not run machine over cord. Keep cord away from heated surfaces.

•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

•Do not handle plug or appliance with wet hands.

•Make sure the machine is plugged into an electrical outlet with the same voltage and frequency rating

as shown on the nameplate of the machine. Do not attempt to plug a 115- volt machine into a 230- volt

outlet.

•Do not immerse or use this machine in standing water. Such use can cause electric shock.

•Keep the electrical supply cord from contacting the rotating brush or drive block.

•Do not expose machine to freezing temperatures.

•To avoid electric shock, do not expose the unit to rain. Store indoors only.

•Connect to a properly grounded outlet only. See “Grounding Instructions.”

•Turn off all controls before unplugging.

•When using an extension cord, use a 3 conductor grounding cord, 12 gauge wire or heavier.

•Do not put any object into openings. Do not use with any opening blocked. Keep free of dust, lint, hair

and anything that may reduce air flow.

•Do not operate machine in flammable or explosive areas.

•All servicing of IPC’s equipment should be performed by an IPC authorized service center.

•Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

•Use extra care when cleaning on stairs. When servicing machine, use manufacturer’s supplied or

approved replacement parts.

FAILURE TO COMPLY WITH THE WARNING INSTRUCTIONS WILL VOID THE

WARRANTY.

GROUNDING INSTRUCTIONS

Machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least

resistance for electrical current to reduce the risk of electric shock. This machine is equipped with a cord

having an equipment-grounding plug. (Figure 1) The plug must be plugged into an appropriate outlet that

is properly installed in accordance with all local codes and ordinances. Do not remove ground pin; if

missing, replace plug before use.

Fig.1

PREPARING THE MACHINE FOR OPERATION

Your floor machine will operate in a wide variety of hard floors and carpet cleaning applications. Consult

with your local dealer or IPC’s Customer Service to select the correct accessories for the job you are

going to perform.

BRUSH, PAD DRIVER, AND PAD INSTALLATION

WARNING: Make sure the power cord is disconnected from the electrical outlet before

installing or removing the brushes, pad drivers or pads from machine.

Brush & Pad Driver installation:

Lock the handle in the upright position and tip the machine back so it

rests on the handle and wheels. Fit the three slots of the clutch plate in

the back of the brush or pad driver over the three lugs of the drive plate.

Push it firmly into position and turn it counterclockwise until it locks in

place.

To remove: Tip the machine back so it rests on the handle and wheels.

Turn the brush or pad driver clockwise until it disengages and lifts off.

Do not store the machine with the brush or pad drivers installed. Fig. 2

Pad Installation:

To install pad, tilt the machine back on wheels until machine is resting on handle. Center the pad on

the pad holder and insert pad center lock by twisting clockwise. Make sure the center lock is tight.

To remove: Twist the center lock counterclockwise.

SHAMPOO TANK INSTALLATION (Dual & Low Speed Units Only)

Position the shampoo tank in front of the floor machine with the water release lever of the shampoo tank

resting below the floor machine lever. There should be enough room for you to pull the shampoo tank

lever without accidentally pulling the floor machine lever. (Figure 3).

Attach the tank to the machine using the two “V” bolts already included on the tank. (Figure 4).

The base of the shampoo tank has a solution hose connected to it on one end. Insert the other end of the

solution hose in the motor frame. (Figure 5)

fig. 3 fig. 4 fig. 5

MACHINE OPERATION

1. Install the pad driver and pad, brush or attachment.

2. Plug in machine.

3. Lower the handle to the desired operating position.

4. Place both hands on the handle grips with your fingers around the on/off

lever which extends from one side to the other underneath the handle grips.

5. The safety “lock-out” lever is located underneath the right side handle

grip and switch lever. To unlock the “lock-out” lever, use your right hand

fore finger to press the lever down toward the back of the switch box. fig. 6

(Figure 6)

6. While still pressing the lever, pull the on/off switch lever to start the

machine, then release the “lock-out” lever. The “lock-out” lever will automatically engage when you

release the on/off switch lever.

TO MANEUVER YOUR FLOOR MACHINE

1. Raise the handle slightly and the machine will go to the right. The higher you raise it, the faster it will

go.

2. Lower the handle and the machine will go left. The more you lower it, the faster it will go.

3. Practice on a smooth surface until you gain experience in operating the unit.

TO RE-ADJUST THE HANDLE-LOCK MECHANISM

Unlock the handle and place it in the upright position. Tighten the adjusting

nuts until there is a slight drag when the handle is raised or lowered.

(Figure7) fig.7

TO ADJUST THE DRIVE BELT:

(High-speed models only: 20HS1500, 20HS2000, 17HS2000)

1. Loosen, but do not remove the 4 bolts, that hold the motor to the

frame. (Figure 5)

2. Tighten the 2 screws at the back of the frame until the belt is tight.

Test and re-adjust the belt until the belt does not slip. Re-tighten the

four motor bolts.

WARNING: Do not over-tighten the belt. fig. 8

OPERATING INSTRUCTIONS FOR MODELS 17DS AND 20DS DUAL SPEED MACHINES

These units operate to all instructions already described except the following:

These models can run at either 175 RPM for scrubbing or at 300 RPM for buffing. To switch the RPM,

use the rocker switch located between the motor and the base of the handle. Do not buff in the 175 RPM

setting because it might overload the motor.

CLEAN UP & STORAGE

1. Unplug and wrap it under the cord hook and around the left side handle grip. Clean the cord and

inspect it for cuts, gashes and loose prongs.

2. Wipe down the machine and store in clean dry place.

WARNING: Do not store the machine with the drive block, pad driver or brush on the

machine.

NOTES

_____________________________________________________________________________________

35 6 7

10 11 12 13 14 15

18 19

32 33

34 35 36 37 38

555657

FM17

IPC Eagle

17LS3-BK 10-19-07

ITEM

NO.

PART NUMBER

DESCRIPTION

QTY.

B11487 Power Cord, 14-3, 50 FT, SJTW

K11498 Grip

C11528 Screw, 10-32 X .25 in

H12066 Label, 1.5 HP, Saturn

H11831 Label, EDIC, Black-Silver

D11496B Switch Box Cover, Black

H11493 Label, Safety, Floor Machine

C11529 Screw, 10-32 X .375 in

K11519 Lever Grip, Lockout, Black

C00278 Locknut, 10-32, Nylon, SS

D11494 Lockout Bracket

D11524 Spring, Lockout

C90007 Screw, 10-32 X .625 Phillips, Truss Head, SS

C11491 Screw, 10-32 X 1 in, SS

D11479 Handle, Chrome, Floormachine

C00306 Roll Pin, .125 X 1.75

D11523 Spring, Trigger

D11495 Trigger, Zinc Plated

K11520 Lever Grip, Trigger, Black

11507A Assembled Locking Handle, Cord Hook

C11619 Allen Wrench, .31 in

D11497 Handle, Locking Clamp

C11538 Cap Nut, .31 in, Push-On

C00259 Washer, Slotted, Zinc

C11536 Spade Bolt, .375-16 X 4 in

D11507 Cord Hook Clamp

D11507-2 Cord Hook Body

C11558 Locknut, Black Oxide, Thin

C11502 Socket Cap Screw, .375-16 X 2.5 in

C11537 Dowel Pin, .31 X 1.5 in

C13101 Screw, Hex Cap, M14-2.0

K00674 Bushing, .50 in, Nylon

D11510 Axle, Floor Machine

D11482 Handle Brace, Right, Black

C00240 Washer, Shoulder, Nylon

C11559 Washer, .515 X .875 X .032

G11943 Wheel, 5 in Saturn

C02305 Cap Nut, .5in Push-on

C11501 Socket Cap Screw, .31 - 18

C00251 Lockwasher, .31, Split

E11477 Bumper, 17 in Floor Machine

D11485B Brush Cover, 17 in, Black

K11521 Spacer, Base, Floor Machine

D11483 Frame, Motor, Black

G11468 Motor W-Gearbox, 1.5 HP

D11481 Handle Brace, Left, Black

H10976-1 Label, UL STD 561-507

H00565-5 Label, Serial #, Standard

H03545 Cover, Serial #, Label

D11490B Drip Cover, Black

H12913 Label, Drip Cover, White

C11916 Screw, 10-32 X .375 Phillips

C13100 Nut, M14-2.0 Nylon Insert

B10734 Strain Relief, Handle

B11513 Cord, Handle, 14-3 SJTW

B11762 Terminal Lug, Nylon, Female

B11465 Switch, DPST, Pushbutton

B00177 Terminal Lug, Female, QD, .25 X .032

C00252 Washer, .375 in, Flat

C11541 Washer, .375 in, Star

B11518 Switch Insulation

C00284 Screw, 10-32 X .375 Ground

B00187 Cable Clamp, Nylon, .43 in.

B00180-10-3 Ring Terminal, #10 Center

B11505 Strain Relief Nut, Metal

C11560 Washer, .93 ID X 1.5 OD

B11504 Strain Relief, Metal

H02548-2 Label, Important, Cord

FM17

ITEM

PART

DESCRIPTION QT

1B11487 POWER CORD, 14-3, 50 FT, SJTW 1

2K11498 GRIP 2

3C11528 SCREW, 10-32 X .25 IN 1

4LABEL, 1.5HP 1

5LABEL, IPC 1

6D11496G SWITCH BOX COVER, GREY 1

7H11493 LABEL, SAFETY, FLOOR MACHINE 1

8C11529 SCREW, 10-32 X .375 IN 2

9K11519 LEVER GRIP, LOCKOUT, BLACK 1

10 C00278 LOCKNUT, 10-32, NYLON, SS 1

11 D11494 LOCKOUT BRACKET 1

12 D11524 SPRING, LOCKOUT 1

13 C90007 SCREW, 10-32 X .625 PHILLIPS, TRUSS HEAD, SS 1

14 C11491 SCREW, 10-32 X 1 IN, SS 1

15 D11479 HANDLE, CHROME, FLOORMACHINE 1

16 C00306 ROLL PIN, .125 X 1.75 2

17 D11523 SPRING, TRIGGER 2

18 D11495 TRIGGER, ZINC PLATED 1

19 K11520 LEVER GRIP, TRIGGER BLACK 2

20 11507A ASSEMBLED LOCKING HANDLE, CORD HOOK 1

21 C11619 ALLEN WRENCH, .31 IN 1

22 D11497 HANDLE, LOCKING CLAMP 1

23 C11538 CAP NUT, .31 IN PUSH-ON 1

24 C00259 WASHER, SLOTTED, ZINC 1

25 C11536 SPADE BOLT, .375-16 X 4IN 1

26 D11507 CORD HOOK CLAMP 1

27 D11507-2 CORD HOOK BODY 1

28 C11558 LOCKNUT, BLACK OXIDE, THIN 2

29 C11502 SOCKET CAP SCREW, .375-16 X 2.5 IN 1

30 C11537 DOWEL PIN, .31 X 1.5 IN 1

31 C13101 SCREW, HEX CAP, M14-2.0 1

32 K00674 BUSHING, .50IN NYLON 2

33 D11510 AXLE, FLOOR MACHINE 1

34 D11482 HANDLE BRACE, RIGHT, BLACK 1

35 C00240 WASHER, SHOULDER, NYLON 6

36 C11559 WASHER, .515 X .875 X .032 6

37 G11943 WHEEL, 5 IN SATURN 2

38 C02305 CAP NUT, .5IN PUSH ON 2

39 C11501 SOCKET CAP SCREW, .31-18 4

40 C00251 LOCKWASHER, .31, SPLIT 4

41 E11477 BUMPER, 17 IN FLOOR MACHINE 1

42 D11485G BRUSH COVER, 17 IN, GREY 1

43 K11521 SPACER, BASE, FLOOR MACHINE 4

44 D11483 FRAME, MOTOR, BLACK 1

45 G11468 MOTOR W- GEARBOX, 1.5 HP 1

46 D11481 HANDLE BRACE LEFT, BLACK 1

47 H10976-1 LABEL, UL STD 561-507 1

48 H00565-5 LABEL, SERIAL # STANDARD 1

49 H03545 COVER, SERIAL #, LABEL 1

50 D11490G DRIP COVER, GREY 1

51 H12913 LABEL, DRIP COVER, WHITE 1

52 C11916 SCREW, 10-32 X .375 PHILLIPS 1

53 C13100 NUT, M14-2.0 NYLON INSERT 1

54 B10734 STRAIN RELIEF, HANDLE 1

55 B11513 CORD, HANDLE, 14-3 SJTW 1

56 B11762 TERMINAL LUG, NYLON, FEMALE 2

57 B11465 SWITCH, DPST, PUSHBUTTON 1

58 B00177 TERMINAL LUG, FEMALE, QD, .25 X .032 2

59 C00252 WASHER, .375 IN, FLAT 1

60 C11541 WASHER, .375 IN STAR 1

61 B11518 SWITCH INSULATION 1

62 C00284 SCREW, 10-32 X .375 GROUND 1

63 B00187 CABLE CLAMP, NYLON, .43 IN 1

64 B00180-10-3 RING TERMINAL, #10 CENTER 2

65 B11505 STRAIN RELIEF NUT, METAL 1

66 C11560 WASHER, .93 ID X 1.5OD 1

67 B11504 STRAIN RELIEF, METAL 1

68 H02548-2 LABEL, IMPORTANT CORD 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IPC Eagle Bodenreinigungsmaschine Handbücher

IPC Eagle

IPC Eagle Integra-D ORB20 Bedienungsanleitung

IPC Eagle

IPC Eagle BB20N Bedienungsanleitung

IPC Eagle

IPC Eagle BX12 Bedienungsanleitung

IPC Eagle

IPC Eagle CT110 Bedienungsanleitung

IPC Eagle

IPC Eagle 1050 Bedienungsanleitung

IPC Eagle

IPC Eagle PB24 Bedienungsanleitung

IPC Eagle

IPC Eagle Propane Powered Floor Care Equipment Benutzerhandbuch

IPC Eagle

IPC Eagle CT70R Bedienungsanleitung

IPC Eagle

IPC Eagle BX2 Fastracts Extractor Bedienungsanleitung

IPC Eagle

IPC Eagle CT230 BT100 Bedienungsanleitung

IPC Eagle

IPC Eagle 1404 Bedienungsanleitung

IPC Eagle

IPC Eagle SC7 Bedienungsanleitung

IPC Eagle

IPC Eagle CT160 700 Bedienungsanleitung

IPC Eagle

IPC Eagle SC4 Bedienungsanleitung

IPC Eagle

IPC Eagle 512 Rider Bedienungsanleitung

IPC Eagle

IPC Eagle ct70 rider Bedienungsanleitung

IPC Eagle

IPC Eagle CT160 Bedienungsanleitung

IPC Eagle

IPC Eagle BT85 Bedienungsanleitung

IPC Eagle

IPC Eagle B2000 Bedienungsanleitung

IPC Eagle

IPC Eagle FLEC02-B Bedienungsanleitung

IPC Eagle

IPC Eagle Cleantime CT230 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch