IPT HRV-601A Bedienungsanleitung

2008

--------------------------------------------------------------- IPT Technologies AB --------------------------------------------------

HRV-601A Scaler/Chipper is very power ul but our advanced,

patented anti-vibration system has reduced vibrations to an

extremely low level. Much lower than other tools in its class assuming

the tools are operated under real world conditions. The low vibration

level makes it possible to use the tool for long periods and for precision

work. The noise level is also remarkably low!

Following these simple instructions will ensure a long life of excellent

operation. ote that this tool needs generous lubrication.

HRV-601A is equipped with a rubber grip

for comfort.

Chisel change is quic and easy.

General In ormation

The Scaler/Chipper is designed to operate at an air pressure of 6,5 to 7

bar, but will tolerate some variations without much change in

performance. Do not exceed 8 bar pressure (although normally the

excess pressure will discharge into the atmosphere). Connect to a 9 mm

or larger hose. Use a an air connection that will not interfere with the end

of the lever (17).

The compressed air should be dry and clean. A filter unit should always

be used. In line lubrication is recommended. Where this is not available,

apply a generous amount of oil at the inlet every 4 hours of operation.

See pages 5 and 7 for information about chisels and extension handles..

______________________________________________________________________________________________________

Address Telephone Tele ax Bankgiro Bank

Tegeluddsvägen 92 at 08-664 34 74 at 08-664 21 55 5799-4188 Handelsbanken

S-115 28 STOCKHOLM Int +46 8 664 34 74 Int +46 8 664 21 55 Lidingö

Important sa ety note

All local safety rules with regard to installation, operation and

maintenance shall be adhered to at all times. Always use adequate

personal protective gear, e.g. safety goggles, noise protection, gloves

etc. as appropriate.

Make sure there is no accumulation of water or dirt in the hose (or the

extension handle) by carefully blowing the hose (and handle) clean

before connecting the tool.

Always disconnect the tool from the air line before changing chisel or

making other adjustments.

Warnings

•Power tools are generally not insulated. Do not use near or in contact

with electric power sources.

•Power tools shall not be used in explosive atmospheres.

•Do not use chisels that are broken, cracked or deformed. Use only

chisels designed for this tool.

•Stored compressed air may cause a hazard.

•Long hair or loose clothing may be drawn in or trapped by the tool.

•Make sure that any sparks that may be emitted are directed so as not

to cause a hazard.

•Be aware of the risk of a whipping compressed air hose.

•Use a face-mask or respirator if dust is created by the work.

Scaler/Chipper page 2

Operation

The Scaler/Chipper is designed for cleaning concrete, heavy weld

chipping, foundry chipping, cleaning etc. Its efficiency is very high

compared to other tools of equal size. The low vibration level makes it

possible to work with higher precision than with other tools and the noise

level is remarkably low.

HRV-601 doesn’t work exactly the same as conventional scaling

hammers. You need to get acquainted with the tool to appreciate the

advantages. It doesn't start to work until there is resistance to the chisel.

For efficient material removal you will find that an intermediate force

works the best.

See below for the correct orientation o the tool and chisel retainer.

The tool is delivered with the throttle lever (17) on the upper side of the

tool. To change the position of the lever, secure the chisel in a vice and

rotate the tool body (force needed) clock-wise into the desired position.

The discharge of the compressed air is through the front of the tool.

Some air circulates in and out of the tool through an opening between

the rear (20) and the housing cover (19). This circulation is directed

downwards but the opening in the housing cover can be rotated to direct

the circulation air as desired.

This side up!

Do not use the tool

upside down!

Scaler/Chipper page 3

Changing the chisel

Simply push the new chisel into the tool until it reaches the bottom of the

chisel holder. Make sure that the chisel has snapped into the right

position by trying to pull it out.

To disconnect the chisel, first push the chisel into the tool or it will

interfere with the release of the loc ing mechanism. Then push the

safety-catch down (see 1) and push the locking mechanism forward as

shown at 2. The chisel can now be removed, 3.

Note

•Always disconnect the hammer from the compressed air hose when

removing or inserting the chisel.

•Do not clamp the housing (18) in a vice. Deformation of the housing

will result in malfunction or poor performance of the tool.

•Do not point the front end downwards when removing the chisel. The

chisel can fall out causing damage to persons and material.

•Use only chisels intended for this tool. (See Accessories below.) They

have a square cross section and have a milled groove as shown in

the Figures above.

Scaler/Chipper page 4

Maintenance

Lubricate regularly (disconnect the scaler from the air hose and apply a

generous amount of oil at the air connection). Use only quality air tool oil.

Use about 1 cm3 for every 4 hours of continuous operation. If the

compressed air already contains oil from a continuous lubrication unit,

then there will generally be no need for extra lubrication. Lack o

lubrication results in excessive wear o critical parts o the tool!

If a large amount of dirt or dust have entered the tool, the filter (28) in the

rear (24) of the tool or on the extension handle can become clogged.

The filter can easily be removed with a wide screwdriver for cleaning. Do

not use too much force downward with the screwdriver as this may

damage the filter.

Accessories

See separate documentation for available chisels using a Cleco type

shank..

The Scaler can be used with an extension handle. See page 7.

Spare Parts Ordering

See the exploded view on the last page for spare parts names and

numbers. For ordering, simply use the prefix H-601- followed by the

number from the table. E.g. Chisel Retainer H-601-02.

Warranty

The HRV-601A Scaler/Chipper is warranted for 12 months from the date

of purchase against faulty workmanship or materials provided the tool

has not been opened by unauthorised persons and has always been

connected to a filtered air supply of the recommended pressure.

Please return any defective tool to your authorised supplier.

This warranty does not include repair or replacement required because

of misuse, abuse or normal wear and tear.

Use only original IPT spare parts for any replacement. Other parts may

result in decreased performance and/or increased maintenance and

wear.

Scaler/Chipper page 5

Technical Data or HRV-601A

Length 233 mm

Length (w/ HRV-600-S1 extension handle) 890 mm

Length (w/ HRV-600-S2 extension handle) 1860 mm

Weight (w/o chisel) 1.75 kg

Vibration Level1≤ 2.5 m/s²

oise Level285 dB (A)

Frequency of Strokes 110 Hz

Maximum Air Flow 115 l/min

Air Pressure 6,5-7 bar

Maximum Air Pressure 8 bar

Maximum Air Temperature 35 °C

Hose Coupling 3/8 inch

Size Hose Recommended 10 mm

1 Per ISO 8662-2 working on a steel ball energy absorber. As shown in ISO 5349 there is a strong correlation between vibration

level and vascular diseases such as e.g. “white fingers”. This is a very low value and doesn't vary much for different working

conditions. Most conventional tools have vibration levels, which are several times higher measured during normal operation.

2 Idling. (When working on metal the noise level is generally higher). The tests were made with microphones placed 1.6 m

above the floor level and 1 m from the surface of the tool with equipment according to class 1 (IEC 651).

Scaler/Chipper page 6

Extension handles

The Extension handles are designed specifically for the HRV-601A and

will give superior ergonomic conditions for the operator.

HRV-601-S1 893 mm (~35.2 inches) total length with tool

HRV-601-S2 1859 mm (~73.2 inches) total length with tool

Make sure there is no accumulation of water or dirt in the hose or the

Extension handle by carefully blowing them clean before connecting to

the tool. The compressed air should be dry and clean. A filter is strongly

recommended.

NOTE

The Throttle Lever (17) will be damaged unless it is completely pressed

down as the tool is screwed onto the Extension handle. After the tool

and handle are correctly assembled, the Throttle Lever of the tool will

remain in the down position (the valve fully open). The tool is now

controlled by the Throttle Lever at the end of the Extension handle.

WARNING!!!

The Throttle lever has to be completely pressed down against the

tool until the Extension handle is inserted ully or the lever will be

damaged!

Scaler/Chipper page 7

HEAVY DUTY – LOW VIBRATIONS

HRV-601A Scaler/Chipper is superior to any heavy duty hammer ever made!

It is very powerful but our patented anti-vibration system has reduced vibrations to

an extremely low level. The low vibration level makes it possible to work with higher

precision than with other tools and the noise level is remarkably low. Try it and

you’ll be convinced that it is the most efficient chipper of its size!

Most efficient choice for:

IPT Technologies AB

•Cleaning concrete

•Heavy weld chipping

•Foundry chipping

•High power needs Rubber grip for

comfort

Extremely low vibrations!

Quick and easy

change of chisel

Lightweight extension handle

comes in two different lengths

1630 mm and 660 mm.

TECHNICAL DATA

(6.3 bar air pressure)

Length Weight Vibration Noise Frequency Air flow Hose Conn. Size Hose

233 mm 1.75 kg <2.5 m/s² 85 dB (A) 110 Hz 1.9 l/s 3/8 inch 10 mm

HRV-601 B is the tool equipped with blow function. Chisels for HRV-601A and B are from the 300 series.

Tegeluddsvägen 92 S-115 28 Stockholm

Telefon: 08-664 34 74 Fax: 08-664 21 55

Andere IPT Medienkonverter Handbücher

IPT

IPT GNV-19 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung