IRUDEK Side Entry Bedienungsanleitung

Poligono Industrial Apatta - C/ Baratzondo, Naves C-14 C-18 Ibarra, Pais Vasco, Spain

943 69 26 17 · [email protected] · www.irudek.com

Side Entry

Operation & Maintenance

Manual

Side Entry

Operation and Maintenance Manual

TABLE OF CONTENTS

1. Introduction

2. Application restrictions

3. General system requirements

4. System set-up and operation

5. Training

6. Inspection

7. Maintenance lubrication and storage

8. Specifications

9. Drawings

10. Inspection log

Base, Horizontal Entry Pt# 30303

Clamp on - Pt# 30321 (shown)

Bolt on - Pt# 30276

Horizontal Entry System

Arm Assembly

Pt# 30235

Work Positioning / Winch

Bracket for Pro 1 Winch only

Pt# 60211 –Pro-2/Pro-3

Mounting Post

Pt # 30303 –19.50”

Pro 1 Winch

Pt# 60217

Mounting Post

Pt # 30234

Horizontal Entry System

Arm Assembly

Pt# 30235

Deck Mount Sleeve

Many other Types of

sleeves may be used.

Side Entry

Operation and Maintenance Manual

1.0 INTRODUCTION

Congratulations on your purchase of a Side

Entry system as part of your Safety at Heights

program. This product is an articulated arm

designed to mount to a variety of support

structures and facilitate entry into access ways

located in the side of various structures. Used

with a winch, the system allows for vertical

positioning within the space being accessed, as

well as rescue and retrieval in the event of an

emergency. Adding a Self-Retracting Lifeline

(SRL) with retrieval capability provides fall

protection as well as rescue capability.

This equipment must be selected and approved

by a Qualified Person, and must be used only

under the supervision of a Competent Person.

All users must have read or have had explained

to them and understood these instructions and

the manufacturer’s instructions supplied with

any accessories or other equipment being use

with this system.

1.1 CONFINED SPACE ENTRY / RETRIEVAL and

RESCUE

The Horizontal Entry Arm, base, and winch, may

be used as part of a system to facilitate access

to and egress from a confined space as well as

non-entry rescue in the event of an emergency.

When used with an approved Irudek Products

mounting base and winch, the Side Entry meets

the requirements of OSHA 1910.146, and

ANSI/ASSE Z117.1 for use as a confined space

entry/retrieval and rescue device.

Side Entry

Operation and Maintenance Manual

1.2 MATERIAL HANDLING

The Horizontal Entry Arm, when combined with a suitable Irudek Products mounting base and winch,

may be used for the raising and lowering of tools, equipment, and other material not exceeding the

rated Working Load Limit of any system component.

NOTE: Some jurisdictions may not allow the use of the same equipment to move personnel and

material. Be aware of and follow the regulations governing your workplace.

2.0 APPLICATION RESTRICTIONS

There are restrictions and limitations that must be carefully considered in the selection, installation, and

operation of this type of equipment. Serious injury or death may result from failure to consider these

factors.

2.1 WORKING LOAD LIMIT

The Horizontal Entry Arm is designed and rated

for a working load limit of 1 person weighing a

maximum of 310lbs (including all clothing, tools,

and equipment) when used in a 1 Part Single

Reeved System as shown in Figure 3.

2.2 SITE CHARACTERISTICS, PHYSICAL and

ENVIRONMENTAL FACTORS

Individual work sites have associated with them any of a number of hazards related to the site itself and

the activities being carried out at that site. These may include, but are not limited to poisonous or

explosive atmospheric conditions, poisonous or corrosive chemical hazards, hot surfaces, electrical

hazards, sharp edges, engulfment hazards, or moving machinery.

All of these factors must be taken into consideration when selecting equipment for a given application.

3.0 GENERAL SYSTEM REQUIREMENTS

The Horizontal Entry Arm is designed for use with a variety of accessories to perform many functions.

There are basic requirements common to all such systems that include, but are not limited to, the

following.

Figure 3:

Side Entry

Operation and Maintenance Manual

3.1 ANCHORAGE STRENGTH

The Horizontal Entry Arm is designed to be set up or installed, and used on a supporting surface

(anchorage) capable of providing sufficient anchorage strength to support all applied loads with an

acceptable margin of safety. The standards governing different situations specify various minimum

requirements depending on the application, the work being performed, and other factors.

However, at no time shall the anchorage provide any less than the greater of:

a 2:1 safety factor on the maximum arrest force (MAF) rating of any fall arrest system being

used,

a 4:1 safety factor on personnel working loads applied to the system,

a 4:1 safety factor on material handling loads applied to the system.

All installations MUST BE used under the supervision of a Qualified Person.

3.2 COMPATIBILITY OF CONNECTORS

Connectors used to connect components in the system must be compatible with each other to ensure

sufficient strength and eliminate the risk of accidental disengagement or rollout during use. Connectors

supplied with products designed, manufactured, and/or approved by Irudek Products Inc. will meet

applicable compatibility requirements for connectors. Any connectors not supplied by Irudek Products

Inc. MUST BE approved by a Qualified Person, and installed, inspected, and used according to the

respective manufacturer’s instructions.

3.3 FULL BODY HARNESS

Use only a full body harness designed, tested, and approved for fall arrest when connecting a person to

this winch. Body belts or straps do not provide adequate support to the body to prevent serious injury

or death in the event of a fall.

3.4 FALL PROTECTION

Activities involving working at heights require the use of equipment to protect the worker in the event

of a fall. Suitable fall protection must be provided as required by applicable local regulations when

using the Side Entry and related equipment.

3.5 CONFINED SPACE SAFETY

When the Side Entry is used as part of a system involving work in a confined space, always follow an

approved confined space safety plan meeting all local regulations.

Side Entry

Operation and Maintenance Manual

4.0 HORIZONTAL ENTRY SYSTEM SETUP and OPERATION

The Horizontal Entry System is designed for use in conjunction with various accessories to meet

different requirements. These may include winches, self-retracting lifelines (SRL’s), and full-body

harnesses. All installations must be approved by a Qualified Person.

4.1 SET-UP / INSTALLATION OF MOUNTING BASES

The Horizontal Entry System is designed for use in two types of bases depending on the given

application. Mounting bases must be set up or installed and used on an anchorage meeting the strength

requirements as specified in Section 3.1.

Setup #1; Manway Flanges from 16” (406mm) to 30” (762mm) Diameter.

1. Remove manway hatch cover as required.

2. Install Base Center Assembly on manway flange, ensure Mounting Post is vertical and tighten

clamps securely using only the attached Clamp Wrench.

3. Insert upper Mounting Leg Assembly, ensure connector engages completely, position clamp

assembly on manway flange, and tighten securely using only the attached Clamp Wrench.

6. Install Winch and any other

accessories following

manufacturer’s instructions

supplied.

Insert lower Mounting Leg Assembly, ensure connector engages completely, position clamp

assembly on manway

flange, and tighten securely 3

using only the attached Clamp

Wrench.

Adjust Mounting Post Height 5

position as required, install Arm

Assembly onto Mounting Post,

and adjust Arm Assembly

horizontal position to center 6

arm in manway.

Side Entry

Operation and Maintenance Manual

Setup #2; Manway Flanges From 35” (889mm) to 54” (1370mm) Diameter.

5. Adjust Mounting Post

Height position as required,

install Arm Assembly onto

Mounting Post, and adjust

Arm Assembly horizontal

position to center arm in

manway.

6. Install Winch and any other

accessories following

manuafacturer’s

instructions supplied.

1. Remove manway hatch cover as required.

2. Install Base Center Assembly on manway flange, ensure Mounting Post is vertical and tighten

clamps securely using only the attached Clamp Wrench.

3. Insert upper Mounting Leg Assembly, ensure connector engages completely, position clamp

assembly on manway flange, and tighten securely using only the attached Clamp Wrench.

4. Insert lower Mounting Leg Assembly, ensure connector engages completely, position clamp

assembly on manway

flange, and tighten securely 3

using only the attached

Clamp Wrench.

Side Entry

Operation and Maintenance Manual

Setup #2; Support Post with Sleeve

The arm may be used with a Support Post into

compatiable Permanent Mounting Sleeve/Bases.

1. Structures selected for the installation of this

system MUST BE capable of supporting a 90,000

in-lb (10,000N.m) moment and 1800 lbs (8kN)

vertical load.

2. Install support post into sleeve/base..

3. Adjust Mounting Post Height position as

required, install Arm Assembly onto support

Post, and adjust Arm Assembly vertically as

needed to center arm in manway.

4. Install and tighen hardware, to enusre arm

assembly does to fall down.

5. Install Winch and any other accessories

following manuafacturer’s instructions supplied.

Side Entry

Operation and Maintenance Manual

10 Form 135033 rev02

08APR2017

4.2 WINCH, SRL, & ACCESSORY INSTALLATION

Please refer to the Operator’s Manual provided with all IRUDEK Products Inc. accessories at the time of

purchase for detailed information on the installation of Winches or SRL’s onto the _Side Entry system.

If you are using a Irudek Built Pro-Series Winch and / or Irudek Line self-retracting lifeline (SRL) with

your Side Entry system;

Insert the slotted tube on the back of the winch or SRL into receiver tube mounted on the Arm

Assembly as shown in Figure 4a and 4b.

Depress the 2 opposing buttons on the connector, and insert the tube until both buttons

engage fully as shown in Figure 4c.

4b 4c

For accessories not supplied by Irudek Products Inc., the Qualified Person responsible for the design,

installation, and use of the system must provide detailed information regarding the installation of the

winch or SRL onto the system.

Install any additional accessories required for the job at hand according to the appropriate Operator’s

Manual or other user instructions as applicable.

Side Entry

Operation and Maintenance Manual

Inhaltsverzeichnis

Andere IRUDEK Sicherheitsausrüstung Handbücher

IRUDEK

IRUDEK TIGER 2,5 Bedienungsanleitung

IRUDEK

IRUDEK SEKURBLOK Bedienungsanleitung

IRUDEK

IRUDEK OREKA Bedienungsanleitung

IRUDEK

IRUDEK COVROP Bedienungsanleitung

IRUDEK

IRUDEK BOREAS HUB Bedienungsanleitung

IRUDEK

IRUDEK LIGHT PLUS 1 Bedienungsanleitung

IRUDEK

IRUDEK LIGHT PLUS P1 Bedienungsanleitung

IRUDEK

IRUDEK PRO 100 Bedienungsanleitung

IRUDEK

IRUDEK Hydro Bedienungsanleitung

IRUDEK

IRUDEK SEKURBLOK Bedienungsanleitung

IRUDEK

IRUDEK CTA Bedienungsanleitung

IRUDEK

IRUDEK MINIBLOK C Bedienungsanleitung

IRUDEK

IRUDEK KARBOR 3,5 Bedienungsanleitung

IRUDEK

IRUDEK X4 LITE Bedienungsanleitung

IRUDEK

IRUDEK NEXION 150 Bedienungsanleitung

IRUDEK

IRUDEK TRIP1 Bedienungsanleitung

IRUDEK

IRUDEK ERO Bedienungsanleitung

IRUDEK

IRUDEK Pro 7 Bedienungsanleitung

IRUDEK

IRUDEK 981 Bedienungsanleitung

IRUDEK

IRUDEK LIGHT PLUS P1 Bedienungsanleitung

IRUDEK

IRUDEK BDREAS HUB Bedienungsanleitung

IRUDEK

IRUDEK LANYARD Bedienungsanleitung

IRUDEK

IRUDEK CTA14 Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung