3
IV. Safety Instructions
Warning: In order to reduce the risk of injury, please keep children away
from it. Always supervise children and incapacitated person contacting or
using this air pump.
Warning: Children shall be kept far away from this product and wire.
Warning: This product is not applicable for the person with declining
physical strength, sensory ability or mental capacity, the person lack of
skill and the mentally retarded person, unless they are under the
protection of their guardians, supervised and directed at the same time.
Warning: Before moving, maintaining, repairing or adjusting this
product, please first pull out the DC plug from the socket.
Warning: Please do not bury the wire in the soil, and it shall be place in
the safe zone where it won't be damaged by mower or other equipment.
Warning: If the power wire is damaged, the power wire must be
changed by the manufacturer or its service agent or the similar
authorized personnel, in case of any risk.
Warning: If you are standing in a place with water or your hands are
wet, please don't plug or pull the DC plug.
Warning: Before inflating, please pay attention to check the maximum
bearable pressure of the inflatable product, because the air bag may be
damaged upon exceeding the maximum bearable pressure.
Warning: Before using, please check the cigarette lighter socket to
make sure that there is no rust or residue inside. The cigarette lighter
socket with poor electric conduction may cause overheating of the
product or power source, which will damage the product.
Warning: The purpose of using this product is limited to the description
in the instruction book.
Warning: Before using, please check the cigarette lighter socket to
make sure that there is no rust or residue inside. The cigarette lighter
socket with poor electric conduction may cause overheating of the
product or power source, which will damage the product.
（Figure 1） （Figure 2）
When the pressure reaches the set value, the air pump will stop working
automatically.
After completing the inflation, pull out the DC plug from the 12V DC
socket.
After pulling out the DC plug, please take down the hose from the air
pump and air bag and store it.
*
*
*
V. Inflation Operation
Connect the end with Flexible conduit adaptor of the hose with the air
pump inflation inlet (1), and twist clockwise to tighten it, as Figure 1.
Install the other end of the hose into the supporting air tap of the air
bag (step①in Figure 2), and twist clockwise to tighten it, and then
insert the inflation valve of the air bag and twist clockwise to fix it
(step②in Figure 2).
Plug the DC plug into the 12V DC socket.
Press the pressure unit toggle button to select the unit you need.
Press the pressurizing button or decompressing button to set
the pressure value you need, with the range of the pressure value
from 0 to 16PSI, (1PSI=0.0689BAR)
After finishing the above steps, press the power switch button
to start to inflate.
During the inflating process, you can press the pressurizing button
or decompressing button to increase or reduce the pressure
value, press the pressure unit toggle button to switch the unit, and
press the On/Off button to stop.
*
*
HT-786 DC12V
*
*
*
*
*
2
IV. Safety Instructions
Warning: In order to reduce the risk of injury, please keep children away
from it. Always supervise children and incapacitated person contacting or
using this air pump.
Warning: Children shall be kept far away from this product and wire.
Warning: This product is not applicable for the person with declining
physical strength, sensory ability or mental capacity, the person lack of
skill and the mentally retarded person, unless they are under the
protection of their guardians, supervised and directed at the same time.
Warning: Before moving, maintaining, repairing or adjusting this
product, please first pull out the DC plug from the socket.
Warning: Please do not bury the wire in the soil, and it shall be place in
the safe zone where it won't be damaged by mower or other equipment.
Warning: If the power wire is damaged, the power wire must be
changed by the manufacturer or its service agent or the similar
authorized personnel, in case of any risk.
Warning: If you are standing in a place with water or your hands are
wet, please don't plug or pull the DC plug.
Warning: Before inflating, please pay attention to check the maximum
bearable pressure of the inflatable product, because the air bag may be
damaged upon exceeding the maximum bearable pressure.
Warning: Before using, please check the cigarette lighter socket to
make sure that there is no rust or residue inside. The cigarette lighter
socket with poor electric conduction may cause overheating of the
product or power source, which will damage the product.
Warning: The purpose of using this product is limited to the description
in the instruction book.
Warning: Before using, please check the cigarette lighter socket to
make sure that there is no rust or residue inside. The cigarette lighter
socket with poor electric conduction may cause overheating of the
product or power source, which will damage the product.
（Figure 1） （Figure 2）
When the pressure reaches the set value, the air pump will stop working
automatically.
After completing the inflation, pull out the DC plug from the 12V DC
socket.
After pulling out the DC plug, please take down the hose from the air
pump and air bag and store it.
*
*
*
V. Inflation Operation
Connect the end with Flexible conduit adaptor of the hose with the air
pump inflation inlet (1), and twist clockwise to tighten it, as Figure 1.
Install the other end of the hose into the supporting air tap of the air
bag (step①in Figure 2), and twist clockwise to tighten it, and then
insert the inflation valve of the air bag and twist clockwise to fix it
(step②in Figure 2).
Plug the DC plug into the 12V DC socket.
Press the pressure unit toggle button to select the unit you need.
Press the pressurizing button or decompressing button to set
the pressure value you need, with the range of the pressure value
from 0 to 16PSI, (1PSI=0.0689BAR)
After finishing the above steps, press the power switch button
to start to inflate.
During the inflating process, you can press the pressurizing button
or decompressing button to increase or reduce the pressure
value, press the pressure unit toggle button to switch the unit, and
press the On/Off button to stop.
*
*
*
*
*
*
*
*
*
*
*
*
*
HT-786 DC12V
ENEN
