Islander ARMR2 Bedienungsanleitung

Maintenance Manual

ARMR2

Major Components

Clicker Assembly

Dragknob

Crank

Spool

Retaining

Screw

Handle Assembly

BearingClutch Assembly

Pawl Assembly

Cam

Assembly

Foot

Frame

Draglever

Crank Assembly

General Information

Thank you for purchasing an Islander ARMR2 model mooching reel.

will help you identify, clean, and lubricate each important component to help keep your reel

performing like new.

Features of the ARMR2

• Handles stay stationary while the line is playing out.

• Full frame construction with one-piece spool and frame.

• Free spool operation controlled with frame-side recessed lever.

• One way large cork disc drag system.

• Face side adjustable drag knob.

• Islander classic outgoing clicker.

• A generous palming rim.

• Engraved serial number on spool and frame.

Technical Suppor t

Telephone 1-250-544-4856

E-Mail info@islander.com

How To Disassemble Your Reel

1. Remove the retaining screw by turning

important that whichever tool you

small may damage the retaining screw.)

2. Remove the dragknob by turning it

counter-clockwise until it is loose.

Underneath the dragknob there will be a

nylon washer. It will either be stuck to the

bottomofthedragknobortothetopof

the dragspring.

3. Remove the crank by pulling it away from

the spool. Grasp the outside of the frame

withonehandandthespoolwiththe

other, and pull the frame and spool apart.

On the back of the spool you may notice

thattheclutchisstucktothebackofthe

spool. You can remove this by grasping

the teeth of the clutch and pulling.

Atthispointthereshouldbe8freeassemblies:RetainingScrew,Dragknob,

Dragknob Washer, Dragspring, Clutch, Crank, Spool, and Frame.

(B) Dragknob Figure 1

(A)RetainingScrew (C)Crank

Cleaning and Lubricating Your Reel

1. Disassemble your reel as shown above.

2. Remove the clutch assembly [1] .

3. Clean the clutch assembly. Remove old grease and

grit using a soft cloth.

4. Clean the base of the spindle, [2]. Remove any old

grease and grit from using a soft cloth.

5. Clean the pawl/cam assembly [A] and [B]. Remove

any old oil and grit using a brush or swab.

6. Oil and grease all indicated locations.

7. After lubrication, work the Draglever [3] back

a forth a few times to work the lubrication

through the cam and pawl assemblies.

8. With the Draglever [3] in the “disengaged”

position, lower the clutch back into position,

cork side up. Re-engage the Draglever [3] .

A) Oil Pawl

B) Oil Cam

C) Grease

Cam

2) Spindle

1) Clutch

Assembly

Figure 2

Figure 3

F) Grease Bearing

Under Clutch

3) Draglever

D) Grease

Teeth of

Clutch

E) Oil Clutch

Cork

Your reel comes from the factory lubricated. Periodic lubrication is recommended to maintain

optimum performance.

F) Oil Clicker

Assembly

Figure 4 Figure 5 - Drag Spring

G) Grease Bearings

(front of spool and

rear of spool)

Figure 6 -

Handle Assembly

9. Remove old oil from the around the clicker

assembly using a brush or swab.

10. Remove old grease from the surface of

the bearings. One bearing is located at [G],

while the other bearing is on the other side

of the spool. If the dragspring [Figure 5] has

not been removed, please do so to clean

and lubricate this bearing.

11. The crank requires a small amount of

dragspring does not require any lubrication.

Just wipe the dragspring o

with a soft cloth.

12. The handle assembly need not be lubricated. Simply remove the screw holding the

Because of the conditions that this style of reel is used under (saltwater), it is important

that the reel be rinsed o under a warm water stream after each trip. While the reel is saltwater safe,

the quick rinse will help your reel perform better in the long run. Avoid immersing the spool in water,

because moisture will be retained by the backing.

Tuning

It is possible to tune both incoming and outgoing

clicks, to a certain extent. For these adjustments,

you will need to disassemble your reel.

outgoing click, push the clicker spring [2] in the

direction indicated by [B], Figure 7. Do not push

spring more than a few degrees, as pushing too

far will remove the outgoing click altogether.

incoming click, push the pawl spring [4] in the

direction indicated by [C], Figure 8.

incoming click, push the pawl spring [4] in the

direction indicated by [D], Figure 8. Do not push

this spring more than a degree.

Figure 8

C) For louder

incomming click

4) Pawl Spring

3) Pawl D) For a quieter

incoming click

1) Clicker

A) For a louder

outgoing click

Figure 7

2) Clicker Spring

B) For a quieter

outgoing click

the outgoing click, push the clicker spring

in the direction indicated by [A], Figure

7. Push the spring until the clicker [1] is

pointing directly at the bearing on the

rear of the spool.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are

info@islander.com | www.islander.com

Reel Maintenance Kit

Use the same lubricant as the pros! A well lubricated and clean reel will last you a lifetime. We recommend

Islander’s Reel Maintenance Kit. It comes with all the lubricants you need for your ARMR2 reel.

Oil: Super Lube® Multi-Purpose Synthetic-based Oil with PTFE®

Grease:

Contact your local dealer or visit www.islander.com.

Inhaltsverzeichnis

Andere Islander Angelausrüstung Handbücher

Islander

Islander ARMR2 Bedienungsanleitung

Islander

Islander MR3 Bedienungsanleitung

Islander

Islander MR3 Series Technische Daten

Islander

Islander IS Bedienungsanleitung

Islander

Islander LX Series Technische Daten

Islander

Islander MR2 Technische Daten

Islander

Islander Steelheader Bedienungs- und Wartungsanleitung

Islander

Islander Trout Series Bedienungs- und Wartungsanleitung

Beliebte Angelausrüstung Handbücher anderer Marken

Kongsberg

Kongsberg Simrad SY50 Bedienungsanleitung

Cannon

Cannon Magnum 5 ST Bedienungsanleitung

Jiffy

Jiffy Pro4 Lite Bedienungsanleitung

Fishmaster

Fishmaster Pro Series Kurzanleitung

MIVARDI

MIVARDI Carp Scout XL Bedienungsanleitung

FLAJZAR

FLAJZAR FISHTRON CatFish TX3 Bedienungs- und Wartungshandbuch

Milwaukee

Milwaukee 2873-20 Bedienungsanleitung

VEXILAR

VEXILAR FL-8SLT Bedienungsanleitung

Fishmaster

Fishmaster Casting Platform Kurzanleitung

Marcum Technologies

Marcum Technologies PanCam Bedienungsanleitung

Harmony

Harmony SlideTrax 8023061 Bedienungsanleitung

Quantum

Quantum Baitcast Reel Bedienungsanleitung

K-Drill

K-Drill Ice Auger Bedienungsanleitung

FISHING SPECIALTIES

FISHING SPECIALTIES Bowducer Bedienungsanleitung

Fox

Fox Receiver Bedienungsanleitung

Abu Garcia

Abu Garcia REVO MGX Bedienungsanleitung

Daiwa

Daiwa TanacomBull 1000 Bedienungsanleitung

Sealey

Sealey HP01 Bedienungsanleitung