Isotech IDM17 Bedienungsanleitung



INSTRUCTION MANUAL

IDM17 PEN-TYPE MULTIMETER

EN FR IT DE

IDM 17

ISO-TECH IDM 17

PEN-TYPE MULTIMETER

INSTRUCTION MANUAL

INTRODUCTION

1-1 Unpacking and Inspection

Upon removing your new Digital Multimeter from its packing, you should have the following items:

1. Digital Multimeter.

2. Test lead (one black).

3. Test probe (Red).

4. Operations manual.

5. Carrying case.

1-2 Meter Safety

Terms marked on Equipment

ATTENTION - Refer to Manual.

DOUBLE INSULATION - Protection Class II.

DANGER - Risk of electric shock

Symbols in this Manual

This symbol indicates where cautionary or other information is found in the manual.

Battery

1-3 Front Panel

Refer to Figure 1 and to the following numbered steps to familiarise yourself with the meter's front panel controls and

connectors.

1. Digital Display — The digital display has a 3200 counts LCD readout with 65 segments analog bar graph, auto

polarity, decimal point, "" AC, DC, RANGE,>, <, , MΩor KΩor Ωand Unit annunciators.

2. Function Switch — Select the Function and Range desired.

3. COM Input Terminal — Ground input connector.

4. V–ΩInput Terminal — Positive input connector for Volts, Ohms and Diode.

5. Range Switch (Manual Range) — "RANGE" switch is pressed to select manual ranging and to change ranges.

When "RANGE" switch is pressed once, "RANGE" annunciator on the LCD is displayed. Press "RANGE" switch

to select appropriate range to be used. Press "RANGE" switch and hold for 2 seconds to return to Autoranging.

6. V, V, Ω<,Selection Switch — Press the blue switch alternately to measure AC Voltage or DC Voltage

in the voltage mode or to measure resistor or continuity or diode in Ω<mode.

7. Hold >Switch — This switch is used to hold measured value for all functions. Press the Hold switch until the ">"

annunciator is displayed. Conversions are made but the display is not updated.

Figure 1

SPECIFICATIONS

2-1 General Specifications

This instrument has been designed in accordance with UL 3111-1 and IEC publication 1010 Pt 1, Class II, Safety

Requirements for Electrical Equipment for measurement, control and laboratory use. This level of safety can only be

guaranteed while the limits of 2.2 are observed.

Display : The Liquid Crystal Display (LCD) has a maximum reading of 3200, and 65 segments bar graph.

Polarity Indication : Automatic, positive implied, negative indicated.

Overrange Indication : "OL" or "-OL".

Low Battery Indication : "" is displayed when the battery voltage drops below operating voltage.

Sampling : 2 times / sec for digit. 12 times / sec for analog bar graph.

Auto Power Off : Approx. 10 minutes.

2-3 Environmental Conditions

Maximum Altitude : 2000m

Installation Category : IEC 1010 600V CAT II 300V CAT III

Pollution Degree : 2

Operating Temperature : 0°C to 50°C, 0 to 80% R.H.

Storage Temperature : -20°C to 60°C, 0 to 80% R.H with battery removed from the meter.

Temperature Coefficient : 0.15 x (Specified accuracy) / °C, < 18°C or > 28°C.

Power Requirements : IEC LR03, AM4 or AAA size 1.5V x 2.

Battery Life : Alkaline 800 hours.

Dimensions (W x H x D) : 42mm x 145mm x 24mm.

Weight (including batteries) : 4 ounces (112 grams).

Supplied Accessories : Battery (installed) and operators' manual.

2-3 Electrical Specifications

Accuracy is ± (% reading + number of digits) at 23°C ± 5°C, less than 75% R.H.

(1) DC Volts

Range Resolution Accuracy Over voltage protection

300mV 100µV

±(0.7% reading+ 2 digits)

3V 1mV

30V 10mV

300V 100mV

600V 1V

600V DC or 600Vrms

Input Impedance : 10MΩ.

Inhaltsverzeichnis

Andere Isotech Multimeter Handbücher

Isotech

Isotech ICM33R II Bedienungsanleitung

Isotech

Isotech ICM A9 Bedienungsanleitung

Isotech

Isotech IDM 91E Bedienungsanleitung

Isotech

Isotech IDM-8341 Series Bedienungsanleitung

Isotech

Isotech IDM 98-III Bedienungsanleitung

Isotech

Isotech IDM 98-III Bedienungsanleitung

Isotech

Isotech IDM 103N Bedienungsanleitung

Isotech

Isotech ICM A7-4 Bedienungsanleitung

Isotech

Isotech IDM19 Bedienungsanleitung

Isotech

Isotech IDM 205 RMS Bedienungsanleitung

Isotech

Isotech IDM101 Bedienungsanleitung

Isotech

Isotech IDM63N Bedienungsanleitung

Isotech

Isotech IDM201N Bedienungsanleitung

Isotech

Isotech IDM99II Bedienungsanleitung

Isotech

Isotech IDM5 Bedienungsanleitung

Isotech

Isotech IDM 97 Bedienungsanleitung

Isotech

Isotech IDM 507 Bedienungsanleitung

Isotech

Isotech IDM19 Bedienungsanleitung

Isotech

Isotech ICM36R Bedienungsanleitung

Isotech

Isotech IDM61 Bedienungsanleitung

Isotech

Isotech IDM97II Bedienungsanleitung

Isotech

Isotech ICM 136R Bedienungsanleitung

Isotech

Isotech IPM 138 Bedienungsanleitung

Isotech

Isotech IDM 91E Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung