iWave FIM-2405 Bedienungsanleitung
www.iwavecomms.com
1st
FIM-2405 User Manual
RX on Ground & TX on Board
Contents
I. Disclaimer ................................................................................................................................................................ 2nd
II. Precautions for integration .................................................................................................................................... 2nd
III. List of in-box items ................................................................................................................................................. 4th
IV. Interface Definition ................................................................................................................................................ 4th
V. Operating Instructions & Steps ............................................................................................................................... 7th
VI. Antenna Installation .............................................................................................................................................10th
6.1. Multi-rotor UAV..........................................................................................................................................10th
6.2. Fixed Wing UAV..........................................................................................................................................11th
IWAVE COMMUNICATIONS CO., LIMITED
V2.0
www.iwavecomms.com
2nd
1. Disclaimer
IWAVE is the registered trademark of IWAVE COMMUNICATIONS CO., LIMITED. All product names
and brands in this manual are trademarks or registered trademarks of the Company. IWAVE
COMMUNICATIONS CO., LIMITED reserves all copyrights of the product and the manual. All the
information must not be copied or reproduced in any form without permission of IWAVE. There may
be semantic differences between disclaimers of different languages. The Chinese version shall
prevail in Chinese mainland, while the English version shall prevail in other regions. Thank you for
purchasing IWAVE FIM-2405. Please use FIM-2405 according to local radio regulations. Before using,
please carefully read this disclaimer. Once the product is used, all the contents of the disclaimer will
be regarded recognized and accepted. Please install and operate the product in strictly accordance
with the requirements of this manual. IWAVE COMMUNICATIONS CO., LIMITED and its affiliates will
not assume any legal responsibility for results or losses caused by improper use, installation,
assembly and modification (including the use of non-specified IWAVE parts and accessories, such as
the radio power amplifier, antenna and SMA extension cord).
2. Precautions for integration
1) Be sure to use the parts provided by IWAVE.
2) Reverse connecting power line positive and negative will burn the device out.
3) Before powering on please make sure the antenna are in good connection and not install or
remove the antennas with power on.
4) Given that the carbon fiber body and metal load may have shielding effects on antenna signals,
they should not be installed between the antenna and ground terminal. Keep the antenna on
board free from winding or blocking by obstacles. The antenna end should be vertically
downward without bending to prevent shortening communication distance and failure
communication.
5) Antennas on board should be kept away from other radio antennas(such as GPS antenna) to
avoid electromagnetic noise and interference.
6) If using PTZ Camera, please do the PTZ self-testing firstly then connect HDMI cable.
7) HDMI cable and antenna on board may interfere with GPS. Please keep the HDMI cable and
antenna away from the GPS module and its cables.
8) Do not disassemble or modify IWAVE FIM-2405. Any problem during installation, contact IWAVE
www.iwavecomms.com
3rd
or IWAVE local branch office.
9) Keep appropriate distances between different electronic devices during installation to minimize
the electromagnetic interference.
10) Before using, please make sure all cables are in good connection and all components can work
properly.
11) After starting the product, the self-test indicators of FIM-2405 will continuously blink for 30s
and then keep bright. Tx camera’s video shown on the monitor connected with Rx means the
device works properly.
12) Check the surrounding environment to ensure there is no other 2.4GHz devices to cause
interference.
13) If you use the Futaba remote controller, Futaba should be adjusted into the French mode.
Otherwise, the video transmission performance will be serious affected.
14) Adjust the Futaba into French mode as following steps:
[LINKAGE MENU]→FRQUENCY→ RTN b→ [AREA]→[FRANCE]
15) Before using, please check the power of RX and TX. If the receiver power off, transmitter on
board will lose connection.
16) Adjusting RX antenna inclination can improve the signal strength and image quality.
17) The camera should be fully charged to ensure normal video output.
18) FIM-2405 support video and duplex data communication. If the video stuck or stopped for
more than 10s. It means the radio signal is weakened or the radio channel is narrowed. In this
case, the aircraft need to fly back to short the distance between TX and RX. Otherwise, the TX
will lose connection.
Notes: Improper operation of FIM-2405 may cause personal injury or damage to properties. Please
pay high attention to operation safety.
www.iwavecomms.com
4th
3. List of in-box items
On board x1
Ground terminal x1
On board antenna x1
Ground antenna x1
Power cable x4
HDMI video cable x2
Network cable x4
S2 Cable: TTL Serial port cable x3(use for S2 port）
Serial TTL to USB serial port x4(use for S1 port)
SMA Cable(Copper wire tinned shield semi-soft line) x4
4. Interface Definition
www.iwavecomms.com
5th
A: HDMI Port on Rx
B: SMA Port
C: HDMI Port on Tx
D: Working Status Indicator
E: S1 TTL Serial Port
F: DC7~18V Input
G: Power On/Off
H: S2 TTL Serial Port
I: Ethernet Port
J: WAN LED
K: LAN LED
L: Mounting Hole
Note: S1 and S2 is same function. If one serial port was broken, the second serial port is standby for use
Note: Working Status Indicator and LED description are as below:
(1) 1, 2, and 3 are signal strength indicators.
1Light 1 on: Signal Weak
2Light 1,2 on: Signal Normal
www.iwavecomms.com
6th
3Light 1,2,3 on: Signal Strong
(2) lights of 1, 2, and 3 are flashing repeatedly in sequence which means the device pairing is unsuccessful, and
Rx and Tx do not communicate.
(3) No. 4 is a data communicate indicator. When data is transmitting normally, No.4 light will keep red. Or it will
not light.
(4) LL: LAN LED
No Ethernet connection: not bright
Ethernet connected but no Ethernet data transmission: keep bright
Ethernet connected and Ethernet data normally transmitted: Fast blink
(5) WL: WAN LED
Tx and Rx not communicate with each other: not bright
Tx and Rx wireless communicate with each other but no signal transmitted: keep bright
Tx and Rx wireless communicate with each other and the signal is normally transmitted: Fast blink
5. TTL Serial Cable Definition
Serial Cable for S1
ZH No.
Color
Signal
1
TXD
White or red
2
RXD
gray or yellow
4
Ground
Black
www.iwavecomms.com
7th
Serial Cable for S2
6.Operating Instructions & Steps
5.1. Make TX and RX and accessories ready.
Besides the items we supply in package box: Tx, Rx, Antennas, Power Cables, Antenna Cable, Ethernet Cable, Serial
Cable and HDMI Cable, you also need to prepare monitor, battery, camera and PC.
ZH No.
Color
Signal
1
Red
TXD
2
Yellow
RXD
3
White
3V3
4
Black
GND
www.iwavecomms.com
8th
5.2.Connection
Make the power cable, HDMI Cable, Ethernet cable, serial port cable and antenna in good connection.
www.iwavecomms.com
9th
5.3. Power on
After checking all the connections are in good condition, turn on
the the video source, LCD display, transmitter and receiver. The
PWR indicator will bright and the whole system starts to work.
5.4. Observe the each indicator’s status
When the device begin to normally start work, all indicators status is described as follow:
1After power on, light 1,2,3 turn green, light 6 turns blue.
2After few seconds, light 1,2,3,6 start flashing. And light 5 keep bright in green color.
3After a few seconds, the device's startup process is completed.
Light 1, 2, 3 keep bright in green color
Light 6 keeps bright in blue color
light 4 keeps bright in red color
Light 5 begins to fast blink in green
4If signal between Tx and Rx is normally transmitted, WL light will fast blink in green.
5After the receiver powered, the”POWER ON” letters will be showed on the display bottom
5.5. Boot up successfully
After successfully connection, the display will smoothly show camera’s video on Tx.
Remark: In UAV application, please make the Tx with Rx connection successfully and the video show on ground
station smoothly then fly the UAV. About how to install the antenna on UAV please refer the following
www.iwavecomms.com
10th
description.
6. Antenna Installation
6.1. Multi-rotor UAV
1) Using SMA metal shielded semi-flexible blue feeder cable provided by IWAVE to connect the TX
SMA port with antenna.
2) The antenna needs to be mounted vertically downwards.
3) The best installation location is UAV ground bracket. With antenna inside, the bracket can only
use fiberglass material.
4) If the ground bracket is automatically retracted, the antenna can be installed in the lower part
of the aircraft.
5) If the antenna is intercepted by the PTZ camera, the video on RX will appear image stuck or
mosaic. At this you need to adjust the UAV’s flying attitude and angle.
SMA Feeder Cable
Inhaltsverzeichnis
Andere iWave Computerhardware Handbücher
iWave
iWave FD-6100 Bedienungsanleitung
iWave
iWave iW-RainboW-G17D Bedienungsanleitung
iWave
iWave FIP-2420 Bedienungsanleitung
iWave
iWave iW-RainboW-G40M Installationshandbuch
iWave
iWave FIM-2410 Bedienungsanleitung
iWave
iWave i.MX53 Installationshandbuch
iWave
iWave iW-RainboW-G28M Zynq-7000 SoC SODIMM SOM Installationshandbuch
iWave
iWave FNM-8416 Bedienungsanleitung
iWave
iWave FIM-2430 Bedienungsanleitung
iWave
iWave iW-RainboW-G35D Installationshandbuch
iWave
iWave i.MX6 Qseven PMIC SOM Installationshandbuch
iWave
iWave FNS-8408 Bedienungsanleitung
iWave
iWave FPM-8416 Bedienungsanleitung
iWave
iWave iW-RainboW-G30D Bedienungsanleitung
iWave
iWave iW-RainboW-G47D Bedienungsanleitung
iWave
iWave iW-RainboW-G40D Bedienungsanleitung
iWave
iWave iW-RainboW-G57M Installationshandbuch
iWave
iWave i.MX 8M Mini Bedienungsanleitung
iWave
iWave FDM-6600 Bedienungsanleitung
iWave
iWave iW-RainboW-G37M Installationshandbuch
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
