Ixon IXrouter2 Bedienungsanleitung
IXrouter2
Installation guide
January 2017
1
Contents
Chapter 1: Overview..................................................................................................................... 2
1.1 Introduction .................................................................................................................. 2
1.2 Package contents........................................................................................................... 2
1.3 Hardware overview ....................................................................................................... 3
Chapter 2: Specifications .............................................................................................................. 4
Chapter 3: Installation .................................................................................................................. 6
3.1 Guidelines for installing the IXrouter.............................................................................. 6
3.2 Installation and removal procedures .............................................................................. 6
3.3 Wiring ........................................................................................................................... 8
3.4 Label ............................................................................................................................. 9
Chapter 4: Operation.................................................................................................................. 10
4.1 Configuration .............................................................................................................. 10
4.2 LED indicators.............................................................................................................. 10
4.3 Factory reset ............................................................................................................... 11
4.4 Planned features ......................................................................................................... 11
Chapter 5: Compliance ............................................................................................................... 12
Chapter 6: Technical support ...................................................................................................... 13
2
Chapter 1: Overview
1.1 Introduction
Thank you for purchasing the IXrouter2. The IXrouter is the standard and best supported hardware
for the IXON IXplatform. The IXrouter makes it very convenient to remotely connect to your
equipment. The built-in firewall keeps your equipment safe from outside threats.
The configuration can be easily done by inserting a USB memory stick, which contains your
configuration file, into the IXrouter's USB port. Generate the configuration from the Tools menu in
your IXplatform account.
The device is available in the following variants.
Product name
Order code
IXrouter2 Ethernet
IX2101
IXrouter2 3G
IX2102
IXrouter2 Ethernet 5-ports
IX2103
IXrouter2 4G-E (EMEA, Korea, Thailand)
IX2105
IXrouter2 4G-A (America)
IX2106
IXrouter2 4G-C (China)
IX2107
1.2 Package contents
IXON IXrouter2 with Weidmuller BL 5.08/04/180 SN BK BX connector
3
1.3 Hardware overview
4
Chapter 2: Specifications
IXrouter2 general specifications
Power supply voltage
12-24 VDC +/- 20%
Max input power
15 VA max.
Operating temperature
0°C to +55°C
Relative humidity
10 to 95% non-condensing
Operating altitude
Up to maximum 2000m
Storage temperature
-20°C to +70°C
Storage humidity
10 to 95% non-condensing
Storage altitude
Up to maximum 3000m
Ethernet ports
Four 10/100 Mbps (3x LAN, 1x WAN)
USB
USB 2.0
Processor
MIPS 360 MHz
Digital Input
Yes
Degree of protection
IP20
Mounting
DIN rail
Size
95 x 95 x 28mm (excl. DIN rail clip)
Weight
270 gram (3G variant)
Certification
CE
Warranty
2 years
5
3G model additional specifications
Protocols and frequencies
UMTS/HSPA+ - 800, 850, 900, 1900,2100 MHz
GSM/GPRS/EDGE - 850, 900, 1800, 1900 MHz
Class
5 bands GPRS/EDGE Class 12
Speed
HSPA+ - Max.14.4Mbps (DL)/Max.5.76Mbps (UL)
UMTS - Max.384Kbps (DL)/Max.384Kbps (UL)
EDGE - Max.236.8Kbps (DL)/Max.236.8Kbps (UL)
GPRS - Max.85.6Kbps (DL)/Max.85.6Kbps (UL)
CSD - 14.4Kbps
SIM size
Standard SIM (2FF)
4G model additional specifications
4G-E protocols and frequencies
(EMEA, Korea, Thailand)
FDD-LTE - B1, B3, B5, B7, B8, B20
WCDMA - B1, B5, B8
GSM/GPRS/EDGE - 850, 900, 1800, 1900 MHz
4G-A protocols and frequencies
(America)
FDD-LTE - B2, B4, B5, B12, B17
WCDMA - B2, B4, B5
GSM/GPRS/EDGE - 850, 1900 MHz
4G-C protocols and frequencies
(China)
FDD-LTE - B2, B4, B5, B12, B17
TDD-LTE - B38, B39, B40, B41
TD-SCDMA - B34, B39
WCDMA - B1, B8
GSM/GPRS/EDGE - 900, 1800 MHz
Speed
LTE-FDD - Max.100Mbps (DL)/Max.50Mbps (UL)
LTE-TDD - Max.61Mbps (DL)/Max.18Mbps (UL)
DC-HSPA+ - Max.42Mbps (DL)/Max.5.76Mbps (UL)
TD-SCDMA - Max.4.2Mbps (DL)/Max.2.2Mbps (UL)
WCDMA - Max.384Kbps (DL)/Max.384Kbps (UL)
EDGE - Max.236.8Kbps (DL)/Max.236.8Kbps (UL)
GPRS - Max.85.6Kbps (DL)/Max.85.6Kbps (UL)
CSD - 14.4Kbps
SIM size
Standard SIM (2FF)
6
Chapter 3: Installation
3.1 Guidelines for installing the IXrouter
The IXrouter is designed to be easy to install on a standard DIN rail. The small size of the IXrouter
allows you to make efficient use of space.
Install the IXrouter inside a cabinet
The IXrouter is an open device. It is required that you install the device in a housing, cabinet
or electric control room.
Heat, high voltage and electrical noise
As a general rule for laying out the devices of your system, always separate the devices that generate
high voltage and high electrical noise from the low-voltage, logic-type devices such as the IXrouter.
When configuring the layout of the IXrouter inside your panel, consider the heat-generating devices
and locate the electronic-type devices in the cooler areas of your cabinet. Reducing the exposure to a
high-temperature environment will extend the operating life of any electronic device.
Consider also the routing of the wiring for the devices in the panel. Avoid placing low-voltage signal
wires and communications cables in the same tray with AC power wiring and high-energy, rapidly-
switched DC wiring.
Provide adequate clearance for cooling and wiring
The IXrouter is designed for natural convection cooling. For proper cooling, you must provide a
clearance of at least 25 mm above and below the device. Also, allow at least 25 mm of depth
between the front of the device and the inside of the enclosure.
3.2 Installation and removal procedures
Dimensions (in mm)
Note that the IXrouter2 Ethernet 5-ports (IX2103) had its height increased by 16mm.
7
Install and remove from DIN rail
The IXrouter can be easily installed on a standard DIN rail. Hang the device on the rail and push the
unit down until you feel a click. To remove the unit, pull/rotate the device up and off the rail.
Install the SIM card
The SIM card slot suits a standard SIM size (2FF).
Remove power
The SIM card may only be removed or inserted if the IXrouter is de-energized.
To insert, push the SIM card into the slot until you feel a click, this is approximately 1mm inside the
device. Release the card and the card will stay in the device. The end of the SIM card should be
aligned with the outside of the enclosure.
To remove, push the SIM card firmly into the slot until you hear a click. Releasing will then cause the
SIM card to partially eject, allowing you to easily take out the card.
8
3.3 Wiring
Proper grounding and wiring of all electrical equipment is important to help ensure the optimum
operation of the IXrouter and to provide additional electrical noise protection for your application.
Power Supply
The IXrouter is supplied with 12 or 24 VDC from an external power source. Be sure you use a safety
Low Power Supply (LPS) in accordance with clause 2.5 of UL/IEC 60950-1 Ed2. Standard: certified for
60°C and for altitudes up to 2000m. The safety LPS power supply is not part of the delivery.
Image below shows the pin-out for the connector.
The IXrouter comes with a female 4-pin plug-in connector with screw connection (type: Weidmuller
BL 5.08/04/180 SN BK BX). The optimal wire diameter is 1.5mm² (22AWG - 12AWG).
Power supply voltage
12-24 VDC +/- 20%
Max input power
10W max
Internal voltage protection
29V max
Input protection
Protected against polarity inversion
Isolation
1.5 kV
Digital input
The function of the digital input is configurable via the IXplatform. Instructions can be found here.
The V- from the power supply is used as common ground
Type
Optocoupler
DI voltage range
0-29 VDC
DI OFF state voltage range
0-3 VDC
DI ON state voltage range
7-29 VDC
DI ON state current range
2-5 mA (typically)
9
Shield
Connect the Shield pin of the IXrouter with the protective earth conductor (PE), min. core diameter
Cu 1.5 mm².
Antenna
The antenna connector is a standard SMA screw connector. Contact your sales agent for optional
external antennas.
The product complies with the R&TTE directive, the FCC, the IC and Japan regulations related
to the GSM modems.
Absolute maximum antenna gain as per FCC's rules and regulations, 47 CFR:
oPart 22H : 5.22dBi;
oPart 27 : 3.31dBi;
oPart 24E : 6.45dBi.
Modifications cannot be made by the user if it influences the normal behavior of the device.
The user shall be informed about modem identification numbers according to their national
authorities:
This product contains part identified as follows by national authorities:
oFFC ID: XMR201510UC20
oIC ID: 10224A-201510UC20
oGITEKI (MIC) ID: 006-00382
oJATE ID: AD160001007
3.4 Label
The label can be found in the bottom right corner on the left side when facing the front side.
PN
Product Name
SN
Serial Number
HW/SW
Hardware and software version
MAC
MAC address of the Ethernet adapter
IMEI
IMEI number of the 3G/4G module (3G/4G model only)
Inhaltsverzeichnis
Andere Ixon Netzwerk-Router Handbücher
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise