Jacobsen HM600 Bedienungsanleitung
GB
United
Kingdom
QUICK START GUIDE
Ransomes HM600 Ride on Flail Mower
STARTING THE ENGINE
SEAT ADJUSTMENT
CONTROLS
DRIVING
MOWING
VISUAL DISPLAY
Refer To The Safety, Operation And Maintenance Manual For Full Operating Instructions.
685428-GB (rev.0)
RJL 100 July 2018
QUICK START GUIDE
en-2
Ransomes Jacobsen Limited reserves the right to make design changes without obligation to
make these changes on units previously sold and the information contained in this manual is
subject to change without notice.
© 2018, Ransomes Jacobsen Limited. All Rights Reserved
QUICK START GUIDE
en-3
BEFORE YOU OPERATE FOR THE FIRST
TIME
• Check and adjust tyre pressure, if
necessary, see Safety, Operation and
Maintenance manual.
• If necessary, add diesel fuel to tank.
• Check engine oil and if necessary fill.
• Check the radiator coolant and fill if
necessary (Water with 50% anti-
freeze).
HOW TO START THE ENGINE
The following procedure is for cold engines.
1. Make sure the forward / reverse pedal
(A) is in the neutral position. The cutter
switch (B) is off and the throttle (C) is in
the centre position.
2. Turn the ignition switch (D) to the right
and hold until the engine starts
(approximately 5-10 seconds.)
3. The glow plugs operate automatically.
The time taken for the engine to start,
depends on the temperature of the
coolant
4. When the engine starts, release the key
immediately. The key returns to the
RUN position.
5. If the engine does not start, return the
key to the OFF position and try again.
NOTES
• If the engine does not start after two
tries, wait 20 seconds and try again.
• The starter motor must not be run
continuously for longer than 30 seconds
or the starter motor can fail.
• If the red LED’s on the display flash
when you start one of the safety
interlock switches was not set correctly.
HOW TO STOP THE ENGINE
1. Disengage drive to the cutting units with
the cutter switch (B).
2. Return the forward / reverse pedal (A) to
the neutral position.
3. Set the parking brake by pressing the
parking brake switch (E).
4. Move the throttle control lever to the
SLOW position.
5. Turn the ignition key (D) to the OFF
position.
STARTING THE ENGINE
12V
10A
1234.51234.5
1234.5
12V
10A
1234.51234.5
12V12V
12V
10A
A
C
D
B
E
A
C
D
B
E
QUICK START GUIDE
en-4
SEAT (GRAMMER MSG85)
Adjustments to the seat can be made for leg
reach, backrest angle and operator weight to
give a good position to operate the machine.
A. FORWARD AND BACKWARD
ADJUSTMENT
To Adjust
The position of the adjusting lever (A) is on
the right hand side of the seat below the seat
cushion. When moved up, the seat may be
moved backward and forward. When, in the
correct position release the lever into one of
the preset positions.
B. BACKREST ADJUSTMENT
To Adjust
The position of the release lever (B) is on the
left hand side of the seat. While, sitting on
the seat pull the release lever up to release
the backrest. (The backrest is spring loaded
to fold forward to the seat Cushion.) Move
back to get the correct position.
Release the lever to engage in one of the
preset positions.
C. WEIGHT ADJUSTMENT
To Adjust
The position of the operator weight adjust
lever (C) is on the front of the seat. To
change the operator weight setting pull the
lever out. When sitting on the seat rotate the
lever until your weight (kg) is shown in the
window.
D.HEIGHT ADJUSTMENT
To adjust
The height of the seat is adjusted by holding
the edge of the seat cushion, pushing your
weight down and lifting. There are three
preset positions. When the highest has been
achieved the seat returns to its lowest
position.
NOTES
The seat is fitted with a microswitch to
sense the operator in the seat.
Wear the seat belt when a ROPS frame or
ROPS cab are installed.
WARNING
Operator weight adjustment must
be set to ensure the OPC
operates correctly. The parking
brake may automatically be
applied if this operation is not
carried out correctly.
SEAT ADJUSTMENT
QUICK START GUIDE
en-5
STEERING TILT CONTROL
When the operators seat is in the correct
position to operate the traction pedal
comfortably. Push the small foot pedal (A) at
the base of the steering column. Tilt the
column backward or forward to the correct
position. Release the small foot pedal to lock
the steering column in position.
STEERING WHEEL ADJUSTMENT
A
QUICK START GUIDE
en-6
CONTROLS
A. Starter key switch.
B. Throttle control.
C. Parking brake switch.
D. Transport lock switch.
E. Cutter switch.
F. 4WD in reverse direction switch.
G. Cruise control switch.
H. Blank on this model
J. DPF Switch
K. Slew control switch (Optional).
L. Road Light switch (Optional).
M. Hazard switch (Optional)
N. Beacon switch (Optional).
P. Right hand unit lift/lower switch.
Q. Centre unit lift/lower switch.
R. Left hand unit lift/lower switch.
S. Cutting unit engaged LCD.
T. Right hand cutting unit in cutting
position LCD.
W. Centre cutting unit in cutting position
LCD.
X. Left hand cutting unit in cutting
position LCD.
Y. Weight transfer button.
Z Visual display.
W
X
R
Y
P
T
S
Q
A
E
M
B
K
C
Z
5 .6
5.5
L
1234.51234.51234.5
12V
10A
F
D
G
J
H
1234.51234.5
12V12V
E
N
B
FD
C
Z
K
5.6
5.5
12V
10A
L
J
M
G
A
H
H
H
QUICK START GUIDE
en-7
CONTROLS
1234.51234.5
12V
12V
E
N
B
FD
C
Z
H
6.6
6.5
12V
10A
L
J
M
G
A
A
E
M
B
K
C
Y
5 .6
5.5
L
1234.5
1234.5
1234.5
12V
10A
F
D
G
J
H
H
W
X
R
Y
P
T
S
Q
A. Starter key switch.
B. Throttle control.
C. Parking brake switch.
D. Transport lock switch.
E. Cutter switch.
F. 4WD in reverse direction switch.
G. Cruise control switch.
H. Blank on this model
J. DPF Switch
K. Slew control switch (Optional).
L. Road light switch (Optional).
M. Hazard switch (Optional)
N. Beacon switch (Optional).
P. Right hand unit lift/lower switch.
Q. Centre unit lift/lower switch.
R. Left hand unit lift/lower switch.
S. Cutting unit engaged LCD.
T. Right hand cutting unit in cutting
position LCD.
W. Centre cutting unit in cutting position
LCD.
X. Left hand cutting unit in cutting
position LCD.
Y. Weight transfer button.
Z Visual display.
QUICK START GUIDE
en-8
CONTROLS
STARTER KEY SWITCH
Turn the starter key to the right to start the
engine. Release the key to return
automatically to the 'on' position for normal
operation.
NOTE: Before the engine starts, the glow
plugs automatically preheat. The visual
display shows the glow plug symbol and
counter to indicate that the automatic
preheat is in operation.
THROTTLE CONTROL ROTARY
Rotate the control to the right to increase the
engine speed and toward the left to
decrease the engine speed.
NOTE: Operate the engine at full speed
PARKING BRAKE SWITCH
Move the orange button back and press the
switch to engage the parking brake.
When the engine is stopped, the parking
brake is applied.
To release the parking brake, press the
opposite end of the switch.
The parking brake icon is displayed on
the visual display screen when engaged.
DO NOT apply the brake while the
machine is in motion.
TRANSPORT LOCK SWITCH
Engages the wing unit locks for transport
The wing unit lock icon is displayed on
the visual display screen when engaged.
QUICK START GUIDE
en-9
CONTROLS
HORN BUTTON
For machines without the lighting kit.
The horn button (A) is on the control panel. If
the lighting kit is fitted, the horn is found on
the end of the indicator stalk.
CUTTER SWITCH
This switch engages the cutter blade
rotation.
To cut grass, push the front of the switch and
move the joysticks forward to lower the
decks. When engaged the yellow LED on the
pod is illuminated.
To stop the blade, push the rear of the rocker
switch.
When lifted out of work or the operator
leaves the seat, blade rotation is stopped.
4 WHEEL DRIVE IN REVERSE SWITCH
Engages the four wheel drive while the
vehicle is in reverse. The switch must be
held to engage.
LIGHT SWITCH (OPTIONAL)
Allows manual operation of the road lights.
Position 1. OFF
Position 2. Side / Marker Lights
Position 3. Main Beam.
Note: Position 3 - Will not activate with
the ignition turned OFF.
QUICK START GUIDE
en-10
BEACON SWITCH (OPTIONAL)
Operates the vehicles rotating beacon
AUXILLARY HYDRAULIC SERVICES KIT
SWITCH (OPTIONAL)
This switch sets the rotary brush or snow
blade to a right side or a left side forward
position.
Push the top of the rocker switch to set a
right side forward position.
Push the bottom of the rocker switch to set a
left side forward position.
CRUISE CONTROL
Used to engage the cruise function when the
cutters are engaged.
Automatic mode should be selected to
enable cruise control.
To engage cruise control:
Push the rocker switch to engage the cruise
function.
To disengage cruise control
Push the rocker switch to disengage the
cruise function.
Note. Operation of the transmission
pedal, applying the parking brake and
reactivation of the cruise control switch
will deactivate the cruise control.
CONTROLS
Inhaltsverzeichnis
Andere Jacobsen Rasenmäher Handbücher
Jacobsen
Jacobsen 62282 Bedienungsanleitung
Jacobsen
Jacobsen Greens King 500A Series Bedienungsanleitung
Jacobsen
Jacobsen Fairway 405 Series Bedienungsanleitung
Jacobsen
Jacobsen R-311 Bedienungsanleitung
Jacobsen
Jacobsen AR30001 Leitfaden
Jacobsen
Jacobsen AR3 Leitfaden
Jacobsen
Jacobsen TR3 EJ Series Bedienungsanleitung
Jacobsen
Jacobsen AR Series Bedienungsanleitung
Jacobsen
Jacobsen HR 5111 Einrichtungshandbuch
Jacobsen
Jacobsen AR-522 jossa ROPS Leitfaden
Jacobsen
Jacobsen HR 9016 Turbo Installationshandbuch
Jacobsen
Jacobsen 62230 Montage- und Wartungsanleitung
Jacobsen
Jacobsen 63286G01 Bedienungsanleitung
Jacobsen
Jacobsen Greens Mower 62238 Bedienungsanleitung
Jacobsen
Jacobsen R-311T Bedienungsanleitung
Jacobsen
Jacobsen Super LF 1880 Bedienungsanleitung
Jacobsen
Jacobsen Tri King Triplex Mower Bedienungsanleitung
Jacobsen
Jacobsen LF 3810 Leitfaden
Jacobsen
Jacobsen 69168 - Turfcat T628D Leitfaden
Jacobsen
Jacobsen Greens King IV Plus Leitfaden
Beliebte Rasenmäher Handbücher anderer Marken
TALEN TOOLS
TALEN TOOLS AVR HGM30 Bedienungsanleitung
DEWEZE
DEWEZE ATM-725 Bedienungsanleitung
Weed Eater
Weed Eater 180083 Bedienungsanleitung
Husqvarna
Husqvarna Poulan Pro PP185A42 Bedienungsanleitung
Better Outdoor Products
Better Outdoor Products Quick Series Bedienungsanleitung
Cub Cadet
Cub Cadet 23HP Z-Force 60 Betriebsanleitung
