Jacuzzi EN27 Series Bedienungsanleitung

TYPE EN27--

TYPE EN37--

OWNER’S MANUAL

WARNING

FORYOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product

must be serviced by a pool technician who is licensed and qualified in pool equipment by the jurisdiction in which the

product will be installed where such state or local requirements exist.In the event no such state or local requirement exists,

the maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all

of the instructions in this manual can be followed exactly. Improper installation and/or operation may void the warranty.

H0722100_REVA

FCC STATEMENT

This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential

installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modications not expressly approved by the part responsible for compliance could void the user's authority to

operate the equipment.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference including interference that may cause undesired operation of the device.

THANK YOU FOR PURCHASING THIS ROBOTIC POOL CLEANER.

YOUR ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED AND TO

PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW CLEANER, PLEASE DO THE

FOLLOWING:

1) Record your purchase information on the spaces provided below.

2) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please call our Technical Support

department at 1-800-822-7933.

RECORD YOUR CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on robot- head)

City State/Province Zip/Postal Code

2ROBOTIC CLEANER

TABLE OF CONTENTS

Important Safety Instructions ...................... 4

Cleaner specications .................................... 5

Technical Specications...................................................................5

Getting Started ................................................ 6

Contents ............................................................................................6

Connect to a Power Source..........................................................6

General Cleaner information......................... 7

Install and Submerge the Cleaner ................................................7

Control Box Buttons.......................................................................8

Start / Stop Cleaning and Select Cleaning Mode ......................8

Removal from Pool..........................................................................8

Using the Lift System.......................................................................8

Maintenance ..................................................... 9

Cord Tangling ....................................................................................9

Clean the Filter Canister..............................................................10

Store the Cleaner When Not in Use ........................................11

Replacing Brushes ..........................................................................11

Troubleshooting............................................. 13

Error Codes ....................................................................................13

Deleting an error code.................................................................13

General Troubleshooting ..............................................................14

OWNER'S MANUAL

SECTION 1. IMPORTANT SAFETY INSTRUCTIONS

Please read through the entire manual before installing your new robotic pool cleaner.The cleaner must be installed

and operated as specied.

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or

death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle should be

provided by a qualied installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI

should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the

GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current

is owing, indicating the possibility of an electric shock. Do not use this product. Disconnect the cleaner and have the

problem corrected by a qualied service representative before using.

• Per the United States National Electrical Code®(NEC®), keep the control box at least ve (5) feet from the edge of

the (pool/spa) water. In Canada, the Canadian Electrical Code (CEC) requires a minimum distance of 3m (10 ft.) to be

maintained between the pool edge and the control box. Never submerge the control box.

• Do not enter pool while the cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and other

equipment.

• To reduce the risk of electrical shock, do not use the robotic cleaner or control box if the cord is worn or damaged.

Contact Technical Support immediately for proper servicing and replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical replacement parts when

servicing. Do not attempt repair of the robotic cleaner, control box, power cord, or oating cable.

• NEVER OPEN CONTROL UNIT.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY; PROVIDE A PROPERLY

LOCATED GFCI RECEPTACLE.THE CONTROL BOX SHOULD BE PLUGGED INTO THE GFCI RECEPTACLE BOX.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of your pool’s

operational system.

4ROBOTIC CLEANER

SAVE THESE INSTRUCTIONS

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal

injury.

• The cleaner must be installed and operated as specied.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A permanently-

installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.

A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its

original integrity.

• Clean the lter canister in the cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

USE OF THE ROBOTIC CLEANER IN A VINYL LINER POOL

• Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objects

coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains, chlorine dispensers, and

automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply by rubbing the surface

with a pool brush. Ink from the pattern can also rub off during the installation process or when it comes into contact

with objects in the pool.We are not responsible for, and the Limited Warranty does not cover, pattern removal, abrasion

or markings on vinyl liners.

SECTION 2. CLEANER

SPECIFICATIONS

2.1 TECHNICAL SPECIFICATIONS

The general specications for the cleaner are as

follows:

Control box supply voltage 100-125 VAC, 60 Hz

Supply voltage 30 V DC

Installed load 150 W max

The cleaner is a double-insulated product.A double-

insulated electrical appliance is one which has been

designed in such a way that it does not require a safety

connection to ground.The basic requirement for

double-insulation is that no single failure can result in

dangerous voltage becoming exposed so that it might

cause an electric shock and that this is achieved without

relying on an earthed (grounded) metal casing.This is

achieved by having two (2) layers of insulating material

surrounding live parts or by using reinforced insulation.

Therefore, devices having double-insulated construction,

such as this cleaner, do not utilize a grounded (three-

prong) cord/plug

OWNER'S MANUAL

SECTION 3. GETTING STARTED

3.1 CONTENTS

The packaging should contain the following items:

• Robotic cleaner and oating cable

• Control box

• Transport and storage caddy

3.2 CONNECT TO A POWER

SOURCE

WARNING

Failure to comply with the following warnings can

result in permanent injury, electrocution or drowning.

PREVENT ELECTRICAL SHOCK

• U.S.: Per NEC® requirements, keep the control

box at least ve (5) ft. (1.5 m) from the edge of

the pool.

CANADA: Per CEC requirements, keep the

control box at least three (3) m (10 ft.) from the

edge of the pool.

• Only connect the control box to a receptacle

protected by a ground fault circuit interrupter (GFCI).

Contact a certied electrician if you cannot verify that

the receptacle is protected by a GFCI.

• Do not use an extension cord to connect the control

box.

• Do not allow anyone to swim while the cleaner is in

the pool.

• The control box is water-resistant, not waterproof. In

order to prevent electrocution, never submerge the

control box or leave exposed to inclement weather.

• Firmly insert power cord connector (with TOP

shown facing up) until you hear a "click"

(Figure 1).

NOTE: The "click" indicates the power cord is connected

correctly.

“HAGA CLIC ”

“HAGA CLIC”

Figure 1. Connect Power Cable

NOTE: To disconnect, firmly grip the power cord

connector on each side, press the two tabs, and pull

out (Figure 2)

"CLICK"

Figure 2. Disconnect Power Cable

6ROBOTIC CLEANER

SECTION 4. GENERAL

CLEANER

INFORMATION

CAUTION

To prevent damage to the cleaner, to adhere to the

following guidelines:

• Remove the cleaner from the pool after the cleaning

cycle is completed.

• Store out of direct sunlight or inclement weather.

• Never lift the cleaner out of the pool by the  oating

cable.

• Take additional care when lifting the cleaner out of the

pool. It becomes heavier when  lled with water.

• Always remove the cleaner from pool when super

chlorinating or adding acid.

• Do not handle cleaner while it is in operation

IMPORTANT

• Always fully submerge the cleaner head before you

begin operation.

• Clean the  lter canister after each cleaning cycle.

• Do not leave your cleaner in the pool on a

permanent basis.

• At the end of each cycle, remove the cleaner from

the pool.

• Start at the cleaner head and untangle any coils in

the cable before storing the cleaner.

The robotic cleaner includes a safety feature that

automatically stops the cleaner if a cleaning cycle starts

but it is not submerged in water. For pools equipped

with a beach area, this safety feature is programmed

to drive the cleaner in reverse and back into the pool

when the impeller is out of the water.

4.1 INSTALL AND SUBMERGE THE

CLEANER

1. With the control box plugged into a power

outlet, spread the  oating cable across the pool

deck until you reach the middle of the pool

length.

WARNING: Do not use an extension cord

2. At the center point, submerge the cleaner in

the pool and hold in the vertical position to

release any air trapped inside.

(Figure 3).

Figure 3. Submerge the Cleaner Vertically

3. Ensure the unit sinks to the bottom of the pool

and does not  oat (Figure 4).

Figure 4. Cleaner Sinking to the Bottom of the

Pool

OWNER'S MANUAL

4. Place all of the  oating cable in the water to

allow free movement in your pool from the

central point. Spread out the  oating cable

ensuring there are no kinks or coils in the

cable (Figure 5).

Figure 5. Pool Entry Point for Optimal

Patterning

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

4.2 CONTROL BOX BUTTONS

The control box can be used to initiate basic cleaning

features.

Button Functions

Start/Stop cleaning

Select cleaning mode

Remove cleaner from the pool

4.3 START / STOP CLEANING AND

SELECT CLEANING MODE

The factory default cleaning mode is set to Floor,Wall,

Waterline.

Use to change cleaning surface setting.

Toggle between modes:

Floor Only (1h 30 min)

Floor,Wall,Waterline (2 hours 30 minutes)

With the cleaner submerged in the water,

press to begin operation.

Press again to interrupt and cancel an in-progress

cleaning cycle.

4.4 REMOVAL FROM POOL

The Lift System is designed to assist in retrieving the

robot from the pool. Lift System can be activated at

any time during or after a cleaning cycle.

1. Press any button to engage cleaner controls.

2. Press on the control box to begin the

automated procedure to bring the cleaner to

the wall.

NOTE: To stop the procedure at any time, press

and release the button again.

3. Next, Press and HOLD to rotate the

cleaner.

4. Once the cleaner is facing the wall of your

choice for retrieval, release the button.

5. Cleaner will drive forward and up the wall

it is facing. It will wait at the waterline to be

retrieved.

6. When in reach, remove the cleaner from the

pool using the handle.The cleaner will quickly

expel water to allow for lighter, easier removal

(Figure 6).

8ROBOTIC CLEANER

NOTE: Never lift the cleaner out of the pool by the floating

cable.

Figure 6. Remove cleaner using the handle

SECTION 5. MAINTENANCE

WARNING

To avoid electric shock and other hazards which

could result in permanent injury or death,

disconnect (unplug) the cleaner from the power

source before performing any cleaning and

maintenance.

5.1 CORD TANGLING

Tangling can occur more frequently when the cleaner

is not attended to after each cleaning cycle. Proper

installation, general maintenance and the following

troubleshooting steps can help to avoid cable

challenges.

IMPORTANT

Cleaner power cable may become tangled if correct

procedure is not followed after each cleaning cycle.

NOTE: Place all of the  oating cable in the water to allow

free movement in your pool from the central point.

Spread out the  oating cable ensuring there are no

kinks or coils in the cable (Figure 7).

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Figure 7. Optimal Entry Point in Pool

If tangling occurs, follow these steps:

1. Remove the cleaner from the pool. When the

cleaner is within arm's reach, use the handle

to remove from the water. Never lift the

cleaner out of the pool by the ﬂ oating

cable.

OWNER'S MANUAL

2. Hold the cleaner vertically to drain

(Figure 8).

Figure 8. Keep Cleaner Vertical to Drain Water

3. Unplug power to the cleaner at the control

box (Figure 9).

Figure 9. Unplug

4. Remove the cleaner from the pool and

untangle all kinks and coils in the power cable.

Start at the cleaner head. Lay the cable in the

sun to loosen any tangling memory (Figure 10).

Figure 10. Untangle the power cable

5.2 CLEAN THE FILTER CANISTER

The  lter canister should be cleaned after each cycle.

1. Remove the cleaner from the water and let the

remaining water drain.

2. Unlatch the cleaner cover to access the

canister (Figure 11).

Figure 11. Lift Cleaner Cover

3. Remove the  lter canister (Figure 12).

Figure 12. Remove Filter Canister

5. Empty all debris from the  lter canister, then

rinse the canister and the cleaner using a hose

(Figure 13).

Figure 13. Wash Filter Canister

NOTE: Periodically, deep-clean the filter canister with soapy

water and a soft bristle brush to prevent clogging.

10 ROBOTIC CLEANER

Andere Handbücher für EN27 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Jacuzzi Schwimmbadreiniger Handbücher

Jacuzzi

Jacuzzi EN27 Series Bedienungsanleitung

Beliebte Schwimmbadreiniger Handbücher anderer Marken

CMP

CMP DEL AOP PRO 200 Bedienungsanleitung

GRE

GRE 90397 Bedienungsanleitung

VGE

VGE Blue Lagoon SPA UV-C 12 WATT Bedienungsanleitung

ICHRoboter

ICHRoboter Pool Cleaner Bedienungsanleitung

Pyle

Pyle SereneLife SLPORBT18 Bedienungsanleitung

Steinbach

Steinbach POOLRUNNER 00-61010 Bedienungsanleitung

Aurelaqua

Aurelaqua SWPCLNAURB5WT Bedienungsanleitung

Hayward

Hayward Aquabug Bedienungsanleitung

Hayward Pool Products

Hayward Pool Products MAGIC CLEAN Bedienungsanleitung

Polaris

Polaris 3900 Sport Bedienungsanleitung

Maytronics

Maytronics MCC8-UNI Bedienungsanleitung

GRE

GRE 90399 Bedienungsanleitung

Blue Lagoon

Blue Lagoon UV-C Pro Buster 450.000 l Bedienungsanleitung

fluidra

fluidra Astral Pool Net'N'Clean Bedienungsanleitung

NETSPA

NETSPA RoPool Bedienungsanleitung

Pool Blaster

Pool Blaster iVAC 250 Li Bedienungsanleitung

Intex

Intex 100A Bedienungsanleitung

Davey

Davey Maverick Bedienungsanleitung