Jadever JCL Bedienungsanleitung

Vetek Weighing AB

JCL 0

User Manual counting scale JCL.

Vetek Weighing AB

JCL 1

Table of Contents

1. Introduction………………………………….……………………………………........

2. Precautions……………………………………….……………………………………..

3. Before Using the Product

3-1 Unpacking and Checking…………………………………………………………………

3-2 Installing Components.………………………………………..………………………….

3-3 Leveling the Scale………………………………………………..……………………….

4. Product Introduction

4-1 Specifications & General Features ………………………………………………………

4-2 Front Panel

4-2-1 Display …….………………………………………………………… ………………….

4-2-2 Keyboard………………………………………………………………………………...

4-3 Power Supply……………………………………………………………………………...

5. Operation

5-1 Basic Weighing

5-1-1 Weighing………………………………………………………………………………….

5-1-2 Tare & Preset Tare……………………………………………………………………….

5-1-3 Unit Switch Operation ……………………………………………...............................

5-2 Basic Counting

5-2-1 Upper & Lower Quantity Limit Checking ………………………………………………

5-2-2 Entering a Known Unit Weight …………….………………………............................

5-2-3 Sample Counting & ACAI …….………..………………………………………………

5-2-4 Accumulation, Accumulation Display and Accumulation Clear………………………

6. Calibration

6-1 Single Point Calibration ……………………………………………………………………

6-2 Linear Calibration……………………………………………………………………………

7. Setting Mode……………………………………………………………………………..

8. Serial Interface

8-1 RS-232 Connector…………………………………………………………………………

8-2 Single Option……………………………………………………………………………….

8-3 RS-232 Output Format……………………………………………………………………

9. Troubleshooting and Error Message………………………………………….

Vetek Weighing AB

JCL 2

1. Introduction

Thank you for deciding to purchase a JCL counting scale from Jadever. This goods has the

excellent performance and splendid properties under severe quality management. It is

recommended to read this manual in full before using it for good function application.

2. Precautions

◎Place the scale on a flat and stable surface. See 3-3 Leveling the Scale for details.

◎Verify that the input voltage and the plug type matches the local AC power supply. See 4-3

Power Supply.

◎Warm up the scale for 15 minutes before using it the first time.

◎Keep the scale away from EMI noise, strong wind and vibration, which might cause

incorrect reading.

◎Avoid sudden temperature changes (suitable operating temperature is between -5℃~ 40℃.)

◎Disconnect the power supply when cleaning the scale.

◎Do not immerse the scale in water or other liquids.

◎Service should be performed by authorized personnel only.

3. Before Using the Product

3-1 Unpacking and Checking

Open the package and check the instrument for transport damage. Immediately inform your

dealer if you have complaints or if parts are missing. The package should contain:

● Scale body ● User manual

● Stainless steel and plastic weighing pans ● Wire (power cord)

3-2 Installing Components

1) Before using the scale, remove the shipping protection screw (rotate counterclockwise),

which located underneath the scale and cork the plug buckle.

Note: the JCL-30K model was shipped without the shipping protection screw.

2) Cover the weighing pans on the scale body properly.

3-3 Leveling the Scale

To compensate for small irregularities or inclinations at the location, the scale can be leveled.

The scale is equipped with a level indicator at the front panel .Adjust the leveling feet until the

air bubble in the indicator is centered as shown.

Note: The scale should be leveled each time its location is changed.

Vetek Weighing AB

JCL 3

4. Product Introduction

1) Leveler

2) Leveling foot 3) RS-232 interface

4) Plastic weighing pan

5) Stainless Steel weighing pan 6) On/Off Switch

7) Two-stage Switch 8) Power socket

9) Transport protection screw 10) Plug buckle

4-1 Specifications& General Features

Specifications

Model

JCL-1.5K

JCL-3K

JCL-6K

JCL-7.5K

JCL-15K

JCL-30K

Capacity(kg)

1.5

7.5

Weighing units

g&lb

kg&lb

Display

3 backlit LCD displays (6/5/6 Digits)

Pan size

294X228X13.5mm

Scale dimensions

341X294X104mm

Power supply

AC 110V/220V (AC±10%) or rechargeable battery（6V/4A）

Vetek Weighing AB

JCL 3

General Features

· A/D covered by aluminium plate, prevent PCB from static and moisture

· Tare, Preset Tare, auto zero tracking

· Automatic counting accuracy improvement (ACAI) for enhanced counting accuracy

· HI/OK/LO quantity checking function

· Stainless steel weighing pan

· Weighing platter easy to disassemble

(with anti-cockroach design)

· Dust proof PVC cover

· Low battery and charging status indication

· Accumulation of weight and quantity (max 99 pieces)

· Single point and linear calibration available

· Auto shut off for power saving

4-2 Front Panel

4-2-1 Display

1) Low battery indication

2) Tare or Preset Tare indication

3) Center of Zero indication, The zeroing range is ±2﹪of weighing capacity.

4) Charge Lamp

Vetek Weighing AB

JCL 4

5) Leveler

6) HI Lamp (ON) Indicating parameter item is selected when setting buzz

sounds. (See 5. Function Setting, setting buzz sounds)

OK Lamp (ON) -- Indicating parameter item or is selected when setting buzz

sounds.

LOW Lamp (ON)—Indicating parameter item is selected when setting buzz sounds.

7) ―PRESET TARE” Symbol ― ‖ points at “PRESET TARE” when Tare value entered via

numeric keys.

8) ―NET” Net weight--Gross weight minus Tare. Symbol ― ‖ points at “NET” when TARE or

PRESET TARE action is done.

9) ―STABLE” Stable indication, Symbol ― ‖ appears at the top of “STABLE” when scale

is in stable condition.

10) ―ACAI” Symbol ― ‖ points at “ACAI” when the average unit weight is calculated or

recalculated.

11) ―M+” Symbol ― ‖ points at “M+” when scale is in accumulation mode.

12) “UW” Under entering a known unit weight mode, Symbol ― ‖ points at ―UW” when

entered unit weight is lower than 4/5 of scale division. Unit weight is too small for ensuring

accurate quantity calculations.

13) ―SMPL” Under the sample counting mode, Symbol ― ‖ points at “SMPL” when

calculated unit weight is lower than 4/5 of scale division or the quantity of sample is less than

10 pieces.

14) “UNIT WEIGHT” Unit Weight Window --Displays the average unit weight value, or

number of weighments.

15) “TOTAL COUNT” Total count window –Displays the calculated number of pieces on the

weighing pan, or accumulated piece count value.

16) “WEIGHT” Weight Window--Displays weight of object on weighing pan, or accumulated

weight value.

4-2-2 Keyboard

1) 0 ~9 numeric keys Enters specific values for tare, unit weight and other data entries.

Vetek Weighing AB

JCL 5

2) ● key Decimal point; toggles between upper limit and lower limit setting when HI-LO-OK

function is enabled. (See 7-2-1)

1) PRINT key Outputs data when Prt.Pr (print stably) is selected as the print mode.

2) ZERO key Zeros the display (within 2% of max.capacity) or cancels Tare action.

3) TARE key Inputs the weight of the object on the weighing pan as a Tare value; inputs

the indicated value entered via the numeric keys as a pre-set Tare value; cancel tare

action.

4) CE key Clears the indicated input values.

5) MC/CK key Short press deletes accumulation records; long press to initial Upper &

Lower Quantity Limit setting.

6) MR key Recalls and displays the total Accumulation data (weight, total count and

number of weightments ) and the first 10 records in details.

7) UWS key Inputs the indicated unit weight value entered via numeric keys

8) M+ key Adds the indicated weight or piece count value intoAccumulation memory.

9) SMPL key Short press enters the sampling mode.

4-3 Power Supply

Power supply

Please verify the local AC power source and switch the two-stage switch to the proper place

before plugging into the power outlet.

Alternative power supply

1) AC 110V/220V (AC±10%)

2) (6V/4A) internal rechargeable battery

Power Consumption

About 300mW (without backlight)

About 380 mW (with backlight)

Low battery warning

When ― ‖ appears in the upper left corner of the weight window, the battery power

requires recharging. The charge lamp turns green from red when the recharging is completed

(which takes about 8 hours). Disconnect the scale from power supply when it is fully charged.

A full charged battery can operate the scale for approximately 65 hrs with backlight, 80hrs

without backlight.

Note: Battery is to replaced only by an authorized service dealer .Risk of explosion can occur

if replaced with the wrong type or connected improperly

Vetek Weighing AB

JCL 6

5. Operation

Here we take JCL-15k model as an example.

5-1 Basic Weighing

5-1-1 Weighing

Place item to be weighed on the scale. The weight

window shown is 2000g, Gross Weight.

5-1-2 Tare & Preset Tare

Tare

When weighing a sample that must be held in a container, taring stores the container weight

into memory.

1) Under the weighing mode, place the container

on the scale, weight window shown is 500g.

Press the key TARE to complete tare action.

The symbol appears and with Symbol ― ‖

pointing at ―NET”.

2）To clear tare, with an empty pan, Press down

the key TARE or key ZERO.

Preset Tare

1) Under the unload condition , Enter tare

value using the numeric keys together with

key ●, then press key TARE.The weight

window displays the tare value.

2) Put the load on the container, the scale will automatically deduct the value of the container

from the total value.

Note: during the process of Tare or Preset Tare, if the load and container are not removed,

press key zero to check the gross weight.

5-1-3 Unit Switch Operation

1) Press key SMPL while powering on the scale.

2) Key in 1132 via numeric keys.

3) Again press key SMPL to enter unit Selection

mode. Numeric key 1is to toggle between g (kg) and

Lb units.

Vetek Weighing AB

JCL 7

4) Press keySMPL to save, and then press key ZERO to return to the weighing mode.

5-2-1 Upper & Lower Quantity Limit Checking

1) Under the weighing mode, press and hold key

MC/CK to initial upper/lower limits setting. (“ ”

is blinking.)

2) Use numeric keys to set the upper/lower Limits.

Key ● is to save upper limit value and advance

to the lower limit setting.

3) When setting is completed, again press key MC/CK to save and return to weighing and

checking mode.

4）To cancel checking action , long Press key MC/CK, then press key ●twice .Checking

action is cancelled, with ― ‖displays momentarily before the screen go back to zero mode.

5-2-2 Entering a Known Unit Weight

1) Under the weighing mode, use the numeric keys

together with key ●to input unit weight value,

and then pressUWS.

2）Put the article on the weighing pan , the

scale starts counting.

Note: “‖ points at ―UW‖ when entered unit weight is lower than 4/5 of scale division.

5-2-3 Sample Counting & ACAI

1) Place samples onto the weighing pan (Or into a tared

container) and input the quantity with numeric keys.

2) Press key SMPL.The unit weight is calculated,

with Symbol ― ‖ Pointing at ―ACAI ‖.

Note:

●The larger the sample size, the more accurate unit weight.

●Symbol ― ‖ points at ―SMPL‖ when calculated unit weight is lower than 4/5 of scale

division or the quantity of sample is less than 10 pieces.

3) Remove the samples and put the load on, the scale begins to count.

4) Press key CE to return to the weighing mode.

Vetek Weighing AB

JCL 8

ACAI

Automatic Counting Accuracy Improvement (ACAI) results in a more accurate count by

increasing the reference weight without the need to count additional parts. Ahigher reference

weight is important when there is a risk of inconsistent piece weights or if the reference weight

is close to the minimum. ACAI uses an initial averaging unit weight to count additional pieces

that are placed on the scale .after a few seconds, the scale gives a beep as the new higher

reference weight is used to recalculate the averaging unit weight. The process can be

repeated as long as the additional weight is less than the previous reference weight. Once

this limit is exceeded ACAI is turned off.

→

5-2-4 Accumulation, Accumulation Display and Accumulation Clear

1) Enter the indicated unit weight, press key UWS

and put first piece of load on the weighing pan

(Or into a tared container). (Refer to 7-2-2)

2) Press key M+, the first accumulation event

is displayed momentarily before Symbol ― ‖

pointing at “M+”. The display reverts to normal

weighing mode in a second, remove the first piece

of load.

3) Put the second piece of load on, then Press key M+ to add the second accumulation event

into memory. Repeat step 2-3 till accumulation actions are finished.

Note: Maximum is 99 pieces.

Accumulation Display

Press key MR to displays the total accumulation data (weight, count and number of

weighments) and the first 10 accumulation events in detail.

Accumulation clear

To clear the total accumulation data or the first 10 accumulation events, Press key MC/CK

while the data is displayed. Symbol ― ‖ disappears when the total accumulation data is

deleted.

6. Calibration

1) For best results, calibrate the scale at regular intervals. Temperature changes, geographic

gravity variations, altitude changes and abuse are few reasons why a scale may need

recalibration.

Andere Handbücher für JCL

Inhaltsverzeichnis

Andere Jadever Skala Handbücher

Jadever

Jadever JCAII Bedienungsanleitung

Jadever

Jadever JWA series Bedienungsanleitung

Jadever

Jadever JC Bedienungsanleitung

Jadever

Jadever JCL Series Bedienungsanleitung

Jadever

Jadever JWE Bedienungsanleitung

Jadever

Jadever JCL Series Bedienungsanleitung

Jadever

Jadever JCAII Bedienungsanleitung

Jadever

Jadever JWE Bedienungsanleitung

Jadever

Jadever SNUGIII Series Bedienungsanleitung

Jadever

Jadever JWE Bedienungsanleitung

Jadever

Jadever LPWN-1530 Bedienungsanleitung

Jadever

Jadever JKH Bedienungsanleitung

Jadever

Jadever JWI 700C Bedienungsanleitung

Jadever

Jadever Jadever SKY Bedienungsanleitung

Jadever

Jadever JCL-3K Bedienungsanleitung

Jadever

Jadever NWTE Bedienungsanleitung

Jadever

Jadever JCN Bedienungsanleitung

Jadever

Jadever JCL Bedienungsanleitung

Jadever

Jadever JWL-1.5K Bedienungsanleitung

Jadever

Jadever JWE-3K Bedienungsanleitung

Jadever

Jadever 1.5K Bedienungsanleitung

Jadever

Jadever JWI-501 Series Bedienungsanleitung

Jadever

Jadever LGCN-3075 Bedienungsanleitung

Jadever

Jadever IDS701-CTRUCK Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung