Jadever JKD 250 Bedienungsanleitung

JADEVER SCALE CO., LTD

JDI SCALE

User’s Manual JD

1. Keypad

ZERO key: Sets the display to zero. (Zero range is within 2% of

maximum

capacity. Initial zero point range is within 20% of maximum capacity)

TARE key:Tares the weight on the scale platform.（

Tare range is over 20d but

less than maximum capacity）

GROSS/NET key:Toggles between gross and net weight.

Sleep/Wake key:Toggles between standby mode and working mode.

I/O key: Power on or off the scale

Note:

◎G.W. =Gross weight

◎N.T. Net weight = gross weight minus tare.

◎JDI-800 can only use the OUTPUT DC 6V /2.5A adaptor. Battery is optional.

◎Please check the power source if there is sudden power failure.

2. Weighing Menu

M+: Adds the indicated weight into Accumulation memory.

Note:

◎Only if the weight is over 20d, can it be accumulated.

◎R

emove the item and the display goes back to zero before the next

accumulation can register.

PRINT: Outputs data.

print modes: manual print /Stable print

Note: Turn off the printer before connect to the scale.

MC: clears previous accumulation data.

Return:Returns to previous menu.

3. COUNT Menu

MR: Adds the indicated weight and

piece count value into Accumulation

memory.

UW Lookup: Recalls unit weight from memory.

Note: I

f there is no weight value or unit weight value, the UW Lookup is not

available.

Store UW: Stores Unit weight into memory.

JADEVER SCALE CO., LTD

JDI SCALE

Clear Count: Clears counting results.

MC: Deletes accumulation records.

M+: Adds the displayed quantity /weight into the accumulating memory.

SAMPLE: Inputs the indicated sample size to calculate average unit weight.

UW: Inputs the indicated unit weight value to calculate the amount of load.

PRINT:Outputs data.

Note: Under the counting mode, only if there is a quantity value

and the stable

indication appears, can it be printed out.

Return Returns to previous menu.

4. SETUP Menu

4.1 NETWORK Sets the network connection.

1) Cable net: Selects cable network as the current network connection.

2) Wifi Conn:Selects Wifi network as the current network connection.

Note:

Auto Update:

If connected to internet, the

system will be updated to the newest version when

the power turns from off to on.

4.2 Set Label Press to initiate label setting.

Label content

%DATE% Date

%TIME% Time

%WEIGHT% Total Weight

%GW% Gross Weight

%NW% Net Weight

%UNIT% Unit Weight

%COUNT% Count

%ACCWEIGHT % Total Accumulation data( total weight)

%ACCCOUNT% TotalAccumulation data( total weight)

%S/N% Serial Number

%TARE% Tare

%TRADENAME % Goods Name (After connected to sto

ck control

system and the material is selected, this content can be printed out )

Barcode category :

CODE39, CODE93, CODE128, UPCA, UPCE, EAN8,

EAN13

Note:

◎

The date and time on the label is based on the scale time setting.

JADEVER SCALE CO., LTD

JDI SCALE

◎only 1-D bar code is supported.

4.3 System Set Press to initiate system setup

1) Auto-Off: Sets the period of inactivity before the scale automatically turns

off.

2) Sound: The scale has been installed button sound and weighi

ng speaker.

Please connect to audio device, if you wish to use this function.

3) Manual Update:

Use the U disk to copy the new program, then insert the U

disk to the USB port which has the marking of “dev”. The system can be

updated by simply pressing Manual Update button.

4) Theme: Press to select your favor theme: blue style or default.

5) Language: Simplified Chinese/Traditional Chinese/English/Spanish

6) TIME: Set time

7) AutoSleep: Sets the period of inactivity

before the scale automatically turns

to standby mode.

Note: The way to wake up the scale

◎Press key Sleep/Wake

◎Click the screen

◎Under weighing mode, click the weighing pan or the screen

4.4 CAL – Calibration

：

For best results calibrate the scale at regular

intervals. This is especially important if the scale is in use for prolonged

periods.

Calibration method I

Arbitrary value: After the zero point calibration finished, input any

calibration value to continue the calibration procedure.

Calibration method II

Cal Setup: Input the calibration points. It will automatically work out each

calibration point value

Multi-point: After setup the calibration point, conduct the calibration

procedure.

Note: When the unit is “Ton”, the capacity and calibration value are set by

unit “kg”

4.5 Set Weight

1) Weight CK-- Check weighing:

Use this mode to compare the weight of an

item to Lower and Upper limits.

High The weight on the weighing pan is greater than the upper limit

OK The weight on the weighing pan is between upper and lower limits.

Low The weight on the weighing pan is smaller than lower limit.

JADEVER SCALE CO., LTD

JDI SCALE

Beep up= There will be a warning sound when the weight/ quantity of articles

exceed the upper limit.

Beep in = There will be a warning sound when the weight/ quantity of articles is

between the upper

Beep low= There will be a warning sound when the material weight/quantity is

less than the lower limit

2) SerialSet—Set serial number

3) Accuracy: Press to initiate accuracy and maximum capacity of the main

scale and remote platform.

Main scale: JDI scale

Remote platform: floor scale or platform scale

Note:

◎Resolution 600-300000

◎JDI-800 indicator can connect two scales simultaneously

4) QTY CK-- Quantity Checking:Use this mode to compare the quantity of

weighing item to Lower and Upper limits.

5) UnitsSet:Sets Unit of measure

Note: Under the weighing mode, press and hold GROSS/NET key to enter

unit setting directly.

6) Zero Range: Sets the range in which the Zero indication turns on. Options

are D0 (1 division), D1 (2divisions), D2 (3divisions), D3 (4 divisions), D4

(5divisions) and D5 (6divisions).

7) Auto Tare: Deducts the value of the container when it’s within the pre-set

values.

8) ACC Set --- Accumulation setting:Sets the maximum accumulation

items and accumulation method.

Stable ACC=Automatically accumulates stable weighing.

Weight OK ACC=Automatically accumula

tes weighing which are between

upper and lower limits.

Count OK ACC=

Automatically accumulates quantity of the material which is

between the upper and lower limit.

Manual ACC=Manual accumulation, press to accumulate weighing.

9) FilterSet: Sets filter level. The higher setting and the better shockproof.

10) Commport: Choose the communication port

11) CommMode: Choose the communication mode to Jadever weighing

software

5. STOCK Menu

After connecting to network, you could use this function for stock control.

JADEVER SCALE CO., LTD

JDI SCALE

◎The stock function is available only after stable indication appears

and there

should be a weight or quantity value.

◎Remove

the item and the display goes back to zero before the next stock

action can register.

◎If the being used unit is weighing unit, the stock acts in weighing mode. I

f the

being used unit is counting unit, the stock acts in counting mode.

6 Initialization

If there is system failure after update, please initial the parameter.

Press and hold key ZERO while powering on the scale. Do

not release it unless

there is a beep sound which means the initialization is finished.

Note: All the setting parameters including accuracy, capacity and calibration are

cleared after initialization.

7 Screen Calibration

Under the main screen, press and hold Sleep/Wake key while pressing down

ZERO key to start screen calibration. During the calibration, press Sleep/Wake

key to wake up the device if it enters the standby mode.

Appendix

Barcode category instruction

Code39:a barcode symbology that can en

code uppercase letters (Athrough Z), digits (0

through 9) and 8

special characters. Possibly the most serious drawback of Code 39 is its low

data density: It requires more space to encode data.

This means that very small goods cannot

be labeled with a Code 39 based barcode. However, Code 39 is still widely used and can be

decoded with virtually any barcode reader. One advantage of Code 39 is that since there is no

need to generate a check digit, it can easily be integrated into existing printing system by

adding a barcode font to the system or printer and then printing the raw data in that font.

Code93: a barcode symbology designed in 1982 by Intermec to provide a higher density

and data security enhancement to Code 39. It is an alphanumeric, variable lengt

h symbology.

Code 93 is used primarily by Canada Post to encode supplementary delivery information.

Every symbol includes two check characters.

Code128: a very high-density barcode symbology. (A special version of it called GS1-

128

is used extensively worldwide

in shipping and packaging industries.) It is used for

alphanumeric or numeric-

only barcodes. It can encode all 128 characters of ASCII and, by

use of an extension character (FNC4), the Latin-1 characters defined in ISO/IEC 8859-

GS1-128 (formerly known as UCC/EAN-

128), not Code 128, is the major component of the

JADEVER SCALE CO., LTD

JDI SCALE

labeling standard for GS1 used as product identification for container and pallet levels in the

supply chain.

•128A (Code Set A) - ASCII characters 00 to 95 (0-9, A-

Z and control codes), special

characters, and FNC 1-4

•128B (Code Set B) - ASCII characters 32 to 127 (0-9, A-Z, a-

z), special characters,

and FNC 1-4

•128C (Code Set C) - 00-99 (encodes each two digits with one code) and FNC1

Universal Product Code (UPC): a barcode symbology, which is widely used in

Canada and the United States for tracking trade items in stores.The UPC has only numerals

with no letters or other characters.

UPC in its most common usage technically refers to

UPC-A which encodes 12 decimal digits. UPC-E only uses a 6-

digit code, does not use

middle guard bars on smaller packages.

EAN-13:Four components :

•The GS1 Prefix, the first two or three digits, usually identifying the national GS1

Member Organization to which the manufacturer is registered (not necessarily where

the product is actually made).

•The Company number, consisting of four, five or six digits

•The Item reference, consisting of two to six digits

•Check digit, a single checksum digit

EAN-8:It was introduced for use on small packages where an EAN-13 barcode would be

too large. It begins with a 2 or 3 digit GS1 prefix (which is assigned to each national GS1

authority) 5 or 4-

digit item reference element depending on the length of the GS1 prefix), and

a checksum digit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Jadever Skala Handbücher

Jadever

Jadever JWI 700C Bedienungsanleitung

Jadever

Jadever JWE Bedienungsanleitung

Jadever

Jadever JWI-700W Bedienungsanleitung

Jadever

Jadever JCL Series Bedienungsanleitung

Jadever

Jadever 1.5K Bedienungsanleitung

Jadever

Jadever JCAII Bedienungsanleitung

Jadever

Jadever JWE Bedienungsanleitung

Jadever

Jadever JCL Bedienungsanleitung

Jadever

Jadever JKH Bedienungsanleitung

Jadever

Jadever LPWN-1530 Bedienungsanleitung

Jadever

Jadever IDS701-CTRUCK Bedienungsanleitung

Jadever

Jadever Jadever SKY Bedienungsanleitung

Jadever

Jadever LGCN-3075 Bedienungsanleitung

Jadever

Jadever JWL-1.5K Bedienungsanleitung

Jadever

Jadever JC Bedienungsanleitung

Jadever

Jadever JCL Series Bedienungsanleitung

Jadever

Jadever JWA series Bedienungsanleitung

Jadever

Jadever JCL-3K Bedienungsanleitung

Jadever

Jadever JCN Bedienungsanleitung

Jadever

Jadever JCL Bedienungsanleitung

Jadever

Jadever NWTE Bedienungsanleitung

Jadever

Jadever JCAII Bedienungsanleitung

Jadever

Jadever JWE-3K Bedienungsanleitung

Jadever

Jadever JWE Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung