Jandy SMARTSYNC60W Bedienungsanleitung
Installation and Operation Manual
Manuel d’installation et d’utilisation
Manual de instalación y operación
Smart Sync®
LED Adapter
Model: SMARTSYNC60W
Compatible with Jandy®
WaterColors LED Light Controller and AquaLink®
Automation Systems (RS, PDA, TCX); Compatible with
Jandy®
WaterColors, Pentair®
IntelliBrite®
, and Hayward®
UCL color modes
WARNING
FOR YOUR SAFETY – This product must be installed and serviced by a contractor who is licensed and qualified in pool
equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. The
maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that
all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning
notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in
property damage, personal injury, or death. Improper installation and/or operation may void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which may cause serious injury, property
damage, or death.
ATTENTION INSTALLER – This manual contains important information about the installation,
operation and safe use of this product. This information should be given to the owner/operator
of this equipment.
Page 2 Page 3
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
Table of Contents
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on circuit different from
that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Section 1. Important Safety Instructions.....................................4
Section 2. Installation....................................................................5
2.1 Select Series ..............................................................................5
2.2 Mount the Smart Sync LED Adapter..........................................6
2.3 Attach Wiring..............................................................................7
2.4 Adjust Brightness.....................................................................10
Section 3. Operation....................................................................10
3.1 J-Series (Factory Default).........................................................10
3.2 H-Series ...................................................................................12
3.3 P-Series....................................................................................14
Page 4 Page 5
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
Section 1. Important Safety Instructions
READ AND FOLLOW ALL INSTRUCTIONS
Specifications
• Smart Sync 60 Watt
–Rated Max Input 5.0A @ 12VAC
–Rated Max Output 4.5A @12VDC
–Controls up to 12 feet of LED waterfalls
• Only use 12VAC input power from a listed low voltage Class 2
landscape or pool/spa lighting transformer.
• Always connect the Class 2 isolated transformer in between pool
controls and Smart Sync.
• Each waterfall requires 5 watts per foot.
ATTENTION
The Jandy Smart Sync LED Adapter should only be used with Smart Sync compatible devices.
Never use in conjunction with the LED Waterfall Colorwheel Controls. Use of the Jandy Smart
Sync LED Adapter requires connection to an automation system or control switch.
Section 2. Installation
WARNING
Risk of electric shock which can result in serious injury or death:
Before attempting to install or service, ensure that all power to the circuit supplying power
to the system is disconnected or turned off at the circuit breaker. All wiring must be done in
accordance with the National Electrical Code®
(NEC®), NFPA70®
. In Canada, the Canadian
Electrical Code (CEC), CSA C22.1, must be followed. All applicable local installation codes
and regulations must be followed.
2.1 Select Series
Each of the three series has a distinct color/show sequence and
matches with a different type of lighting.
1. Determine which series to use based on the type of lighting the
Smart Sync LED Adapter will be controlling:
• Jandy®: J-Series (1)
• Hayward®Industries: H-Series (2)
• Pentair®Water Pool and Spa, Inc.: P-Series (3)
2. Using a flathead screwdriver, rotate the dial on the side of the
Smart Sync LED Adapter to the corresponding number for the
series you want to select (see sticker on LED adapter).
See Figure 1.
Figure 1. Turning dial with screwdriver
SAVE THESE INSTRUCTIONS
Page 6 Page 7
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
2.2 Mount the Smart Sync LED Adapter
Mount the Smart Sync LED Adapter in a NEMA approved
weatherproof enclosure using the included mounting screws, as
shown in Figure 3. Enclosure is not included.
Minimum Enclosure Size (Internal): 9″x 3″x 4″(228 mm x 100 mm x
75 mm)
5.63″
(143 mm)
1.51″
(38.40 mm)
Figure 2. Smart Sync LED Adapter dimensions
Figure 3. NEMA approved weatherproof enclosure
2.3 Attach Wiring
2.3.1 Wiring Steps
CAUTION
The Smart Sync LED Adapter must be powered by a listed low voltage Class 2 12VAC output
transformer. Connect the low voltage transformer between pool control system and Smart
Sync LED Adapter.
1. Wire to the Smart Sync compatible device. Strip the four RGB or
five RGBW wires by at least ¼″. (Compatible with both solid and
stranded wire 24–14 AWG.)
2. Attach each of the four or five wires to the Smart Sync LED Adapter
by pushing back an orange spring clamp and inserting the correct
wire below. If needed, push back the orange spring clamps to
release wires. See Figure 4 for wire stripping and insertion, Figure
5 for RGB wiring, and Figure 6 for RGBW wiring.
3. Repeat steps 1 and 2 to connect wiring from the listed Class 2
12VAC transformer.
Strip wires by at least ¼″
Spring Clamp
Figure 4. Wire stripping and insertion
Page 8 Page 9
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
RED
GREEN
WHITE
BLACK
WHITE
BLACK
From 12VAC transformer To compatible device
Figure 5. RGB wiring
From 12VAC transformer To compatible device
RED
GREEN
BLACK
WHITE
BLACK
WHITE
BLUE
Figure 6. RGBW wiring
2.3.2 System Wiring Examples
One LED Waterfall
Smart Sync
Adapter
12VAC
Transformer
To Pool
Control
System
12V DC 12V AC
To Pool
Control
System
Multiple LED Waterfalls (With One Smart Sync Adapter) Smart Sync
Adapter
Junction
Box
12VAC
Transformer
To Pool
Control
System
Smart Sync
Adapter
12VAC
Transformer
Multiple LED Waterfalls (With Multiple Smart Sync Adapters)
To Pool
Control
System
Smart Sync
Adapter
12VAC
Transformer
LED Waterfalls & Other Lighting
Page 10 Page 11
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
Table 1. J-Series Colors and Shows Sequence
Sequence
Order Color/Show
1 Alpine White
2 Sky Blue (primary blue)
3 Cobalt Blue (dark blue)
4 Caribbean Blue (light blue)
5 Spring Green (light green)
6 Emerald Green (primary green)
7 Emerald Rose (warm yellow)
8 Magenta
9 Violet
10 Slow Color Splash (slow fading color show)
11 Fast Color Splash (fast fading color show)
12 America the Beautiful (red/white/blue show)
13 Fat Tuesday (blue/pink/light green show)
14 Disco Tech (rapid exciting color show)
2.4 Adjust Brightness
WARNING
Turn off all power to the Smart Sync LED Adapter before opening enclosure and adjusting
brightness.
1. Turn off all power to the Smart Sync LED Adapter before opening
enclosure.
2. Open the enclosure door.
3. Adjust brightness by rotating the dimmer dial. There are eight
brightness settings from 0–7, with 0 being the brightest setting.
NOTE: Follow the same steps when adjusting brightness after initial
installation.
Section 3. Operation
ATTENTION
Incorrect wire connections will affect color sequencing. For problems with color sequence
and/or synchronization, check wire connection(s) and wire color coding.
3.1 J-Series (Factory Default)
1. Turn the light ON.
2. Turn the light OFF and ON within three seconds repeatedly until
you reach the desired color or show. See Table 1 for the color
sequence.
NOTE: When the light is OFF for more than seven seconds, it will remain on
the last active color or show.
3.1.1 Reset J-Series Lights
To reset the light to the beginning of the color sequence (Alpine White):
3. Turn the light OFF.
4. Wait four to six seconds.
5. Turn the light ON.
Page 12 Page 13
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
3.2 H-Series
1. Turn the light ON.
2. Turn the light OFF and ON within ten seconds repeatedly until
you reach the desired color or show. See Table 2 for the color
sequence.
NOTE: When the light is OFF for more than 60 seconds, it will remain in
the last active color or show. When the light is turned back on, it
will display white for 15 seconds before returning to that last active
color or show.
3.2.1 Sync H-Series Lights
If some lights are displaying different colors or out-of-sync shows,
follow these steps to sync them again:
1. Turn the light OFF.
2. Wait between 11–14 seconds.
3. Turn the light ON.
Table 2. H-Series Colors and Shows Sequence
Sequence
Order Color/Show
1 Voodoo Lounge (fast fading color show)
2 Deep Blue Sea (dark purple/blue)
3 Royal Blue
4 Afternoon Skies
5 Aqua Green
6 Emerald (green)
7 Cloud White
8 Warm Red
9 Flamingo (pink)
10 Vivid Violet
11 Sangria (purple)
12 Twilight (slow fading color show)
13 Tranquility (blue tones show)
14 Gemstone (green/blue/red show)
15 USA (red/white/blue show)
16 Mardi Gras (purple/orange/green show)
17 Cool Cabaret (medium fading color show)
Page 14 Page 15
ENGLISH Jandy®Smart Sync®LED Adapter | Installation & Operation Manual Jandy®Smart Sync®LED Adapter | Installation & Operation Manual ENGLISH
3.3 P-Series
1. Turn the light ON.
2. Turn the light OFF and ON the required number of times to
display the desired color or show. See Table 3 for required
numbers.
NOTE: P-Series lights always start over at 1 when changing the color/show.
For example, to change the light from Party Mode (2) to California
Sunset Mode (6), you need to turn the light OFF and ON 6 times, as
listed in Table 3.
3.3.1 Hold and Recall Features
Save unique colors (e.g. when one color is fading into another in the
middle of a show) by using the Hold and Recall features.
• To save a unique color, turn the light OFF and ON 13 times starting
when the light is displaying the desired color effect.
• To display the saved color, turn the light OFF and ON 14 times.
Table 3. P-Series Colors and Shows
Number Color/Show
1 SAm®Mode (blue/magenta/white/green show)
2 Party Mode (fast fading color show)
3 Romance Mode (medium fading color show)
4 Caribbean Mode (green/white/blue show)
5 American Mode (red/white/blue show)
6 California Sunset Mode (warm tone color show)
7 Royal Mode (purple/orange/green show)
8 Blue
9 Green
10 Red
11 White
12 Magenta
13 Hold Feature
14 Recall Feature
Zodiac Pool Systems LLC
2882 Whiptail Loop # 100
Carlsbad, CA 92010, USA
Jandy.com | 1.800.822.7933
Zodiac Pool Systems Canada, Inc.
2-3365 Mainway
Burlington, ON L7M 1A6, Canada
Jandy.ca | 1.800.822.7933
A Fluidra Brand
©2023 Zodiac Pool Systems LLC. All rights reserved. ZODIAC®
is a
registered trademark of Zodiac International, S.A.S.U., used under license.
All other trademarks are the property of their respective owners.
H0785800_REVB
CONFORMS TO
UL STD 8750
Certified to CSA
STD C22.2 250.13
Installation and Operation Manual
Manuel d’installation et d’utilisation
Manual de instalación y operación
Adaptateur DEL Smart Sync®
Modèle: SMARTSYNC60W
Compatible avec le contrôleur de lumières à DEL Jandy®
WaterColors et les systèmes d’automatisation (RS, PDA, TCX) AquaLink®
Automation Systems; Compatible avec les modes de couleurs Jandy®
WaterColors, Pentair®
IntelliBrite®
et Hayward®
UCL
AVERTISSEMENT
POUR VOTRE SÉCURITÉ : Ce produit doit être installé et entretenu par un entrepreneur qualifié en équipements de
piscine disposant d’un permis délivré par la juridiction dans laquelle le produit est installé lorsque de telles exigences
étatiques ou locales existent. L’agent d’entretien doit être un professionnel disposant de suffisamment d’expérience
dans l’installation et l’entretien de l’équipement de piscine, afin de s’assurer que toutes les directives du présent
manuel sont scrupuleusement respectées. Avant d’installer ce produit, lire et suivre tous les avertissements et toutes
les directives qui accompagnent ce produit. Tout non-respect des instructions d’avertissement peut entraîner des
dommages matériels, des blessures corporelles ou même la mort. Une mauvaise installation ou utilisation annule la
garantie.
Une mauvaise installation ou utilisation peut engendrer un danger électrique pouvant entraîner des dommages matériels
ou des blessures graves, voire mortelles.
À L’ATTENTION DE L’INSTALLATEUR: Le présent manuel contient des informations importantes sur
l’installation, le fonctionnement et l’utilisation sécuritaire de ce produit. Ces informations doivent
être transmises au propriétaire ou à l’utilisateur de cet équipement.
Inhaltsverzeichnis
Sprachen:
