Jandy JUVMP120 Bedienungsanleitung

Installation and Operation Manual

Manuel d’installation et d’utilisation

Manual de instalación y operación

UV Medium Pressure

Models JUVMP120, JUVMP200, JUVMP320, JUVMP700)

WARNING

FOR YOUR SAFETY – This product must be installed and serviced by a contractor who is licensed and qualiﬁed in pool equipment by the jurisdiction in which the product will be installed

where such state or local requirements exist. The maintainer must be a professional with sufﬁcient experience in pool equipment installation and maintenance so that all of the instructions

in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices

and instructions may result in property damage, personal injury, or death. Improper installation and/or operation may void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which may cause serious injury, property damage, or death.

ATTENTION INSTALLER – This manual contains important information about the installation, operation and safe use of this product. This information should be given

to the owner/operator of this equipment.

Page 2

ENGLISH Jandy®UV Medium Pressure | Installation & Operation Manual

Table of Contents

EQUIPMENT INFORMATION RECORD

DATE OF INSTALLATION _______________________________________________________________________________

INSTALLER INFORMATION _____________________________________________________________________________

INITIAL PRESSURE GAUGE READING (WITH CLEAR FILTER) ____________________________________________

PUMP MODEL ________________________________ HORSEPOWER ____________________________________

NOTES _______________________________________________________________________________________________

______________________________________________________________________________________________

SAVE THESE INSTRUCTIONS

Section 1. Important Safety Instructions.........3

1.1 Safety Instructions .........................................3

Section 2. General Description.........................4

2.1 UV Disinfection............................................... 4

2.2 Product Speciﬁcations................................... 5

2.3 Product Contents........................................... 7

Section 3. Installation ........................................7

3.1 General Considerations..................................7

3.2 UV Reactor Installation...................................7

3.3 Control Panel Installation ...............................9

3.4 Control Panel: Field Wiring Diagram ............10

3.5 Bonding and Grounding...............................11

3.6 UV Lamp Connection................................... 12

3.7 SI5004 Flow Sensor Installation...................13

3.8 UVX-SE Radiation

Sensor Installation........................................ 13

3.9 TM4411 Temperature

Sensor Installation........................................ 14

3.10 JUVMPAUTO Electric Wiper

Driver (Optional) Installation .........................14

3.11 Controls and Indicators................................ 15

3.12 Start-Up........................................................15

Section 4. Operation........................................ 16

4.1 System Main Screen ....................................16

4.2 Language Selection......................................17

4.3 Date / Time Conﬁguration ............................17

4.4 System Initialization .....................................18

4.5 Alarm Management......................................18

4.6 UV Lamp(s) Power

Circuit(s) Diagnostics ...................................19

4.7 System Event Log ........................................20

4.8 System Auxiliary

Parameters Conﬁguration ............................20

Section 5. Maintenance...................................22

5.1 QuartzSleeve Mechanical Cleaning ............22

5.2 UV Lamp Replacement ................................22

5.3 Chemical Cleaning / Replacement

of the Quartz Sleeve..................................... 23

5.4 Replacing Seals in Contact

with the Quartz Sleeve .................................24

5.5 UV-C Sensor Cleaning .................................24

5.6 Veriﬁcation of the Control Panel Fan............25

5.7 Wiper Driver (JUVMPAUTO Module)

Installation ....................................................25

5.8 System Isolation and

Connections Control ....................................25

Section 6. Troubleshooting .............................26

Section 7. Exploded Views and

Replacement Kits...........................26

Page 3

Jandy®UV Medium Pressure | Installation & Operation Manual ENGLISH

Section 1. Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

1.1 Safety Instructions

WARNING

When installing and using electrical equipment, basic safety precautions should always be followed, including the following:

A yellow-green wire connector marked *is provided on this unit to connect a minimum No. 8 AWG for US (UL) and a No. 6 AWG for Canada (CSA)

solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe or conduit within

5feet (1.5 m) of the unit.

Two bonding lugs marked *are provided on the end ﬂanges of the UV chamber suitable for No. 8 AWG (US) and No. 6 AWG (Canada) and secured

to the chamber by paint breaking washer and nut.

* IEC 60417, symbol 5019

WARNING

This product must be connected to a circuit protected by a ground fault circuit interrupter.

Pool end use. Do not use this system to a different application for which it was designed.

The equipment should be installed and handled by truly qualiﬁed people.

Current electrical and accident prevention regulations should be followed.

Under no circumstances will the manufacturer be held responsible for the assembly, installation or start-up, nor any handling or ﬁtting of components

unless they are carried out on its premises.

WARNING

Check all the electrical connectors are well tightened to avoid false contacts and their consequent overheating.

Install the control panel so that the cooling grids are not obstructed.

For indoor use only. This unit is not intended for outdoor use.

Prior to the installation or replacement of any system component make sure it has been previously disconnected from the mains, and there is no water

ﬂow through it. Use only spare parts supplied by Jandy.

WARNING

Never remove the lock nut of the quartz sleeve when the water is recirculating through the UV reactor as it could be expelled and causing damage.

The UV light generated by this equipment can cause serious damage if the eyes or skin are exposed directly to the lamp. Never connect the system

when the lamp is out of the reactor.

Do not handle the UV lamp until completely cold.

Always handle the UV lamp with gloves, as fat and other impurities deposited on the surface may reduce its performance and durability. In case you

have to clean the lamp surface use a soft cloth soaked with alcohol.

Page 4

ENGLISH Jandy®UV Medium Pressure | Installation & Operation Manual

Section 2. General Description

2.1 UV Disinfection

The germicidal effects of ultraviolet light (UV) with

wavelengths around 260 nm are well known for over

100 years. Its use has been increasing in recent years

as it presents a number of advantages over chemical

disinfection systems, since virtually UV light no alters

the physical and chemical composition of water, it

is very effective against any type of microorganism

(algae , bacteria, viruses, fungi, yeasts, etc.) further

minimizing the risks of handling and dosing of

potentially hazardous chemicals. Moreover, UV

treatment reduces the levels of combined chlorine in

water, thereby producing signiﬁcant water savings

by reducing the volume and frequency of renewal of

pool water.

The Jandy UV MP treatment system, in addition

to maintaining a certain level of chlorine in pool

water, ensures the sanitary quality of pool water.

The treatment system will operate when the pool

recirculation (pump and ﬁlter) is operational.

The treatment systems are designed and

manufactured with the latest technology in UV

treatment of water, thus ensuring continuous

operation and minimal maintenance.

The proposed control architecture for the treatment

system has a number of features that allow the

highest levels of reliability, efﬁciency and scalability.

• Because the systems incorporate both radiation

and ﬂow calibrated sensors, continuous

adjustment of the lamp power is allowed, thus

optimizing energy consumption and lifetime.

Calibrated sensors do not require any user

action on them, which does not happen with the

previous range of UV systems.

• Unlike the previous range, Jandy UV MP systems

manage two parameters when setting the lamp

power, radiation measured by the sensor and

ﬂow. Thus, the system sets a nominal radiation

for each model, which is determined by the

maximum treatment ﬂow to ensure a minimum

disinfection efﬁciency. If the ﬂow to be treated

is less than nominal, so too will be the radiation

needed, so the systems will decrease the lamp

output power, optimizing energy consumption

and increasing lamp lifetime. Like the previous

range, whether radiation decreases due to loss

of lamp efﬁciency, turbidity, etc., the system will

adjust the lamp power.

• The lamp power system is based on an electronic

ballast which allows continuous operation with

high efﬁciency (greater than 95%).

Page 5

Jandy®UV Medium Pressure | Installation & Operation Manual ENGLISH

2.2 Product Speciﬁcations

JUVMP120 JUVMP200 JUVMP320 JUVMP700

Flow (UVT 94%)1110 gpm

25.0 m3/h

175 gpm

39.7 m3/h

310 gpm

70.4 m3/h

600 gpm

136.2 m3/h

Material

Control panel Metallic, polyester-epoxy resin coating RAL 7035 / IP-54

UV reactor AISI-316L

Flanges Inlet/Outlet 4" (ANSI) 6" (ANSI)

Max. rated pressure 50 psi / 3.45 bar

Head loss 0.00 psi @ 110 gpm

0.00 psi @ 50 m3/h

0.01 psi @ 175 gpm

0.05 psi @ 39.7 m3/h

0.03 psi @ 310 gpm

0.03 psi @ 70.4 m3/h

0.03 psi @ 600 gpm

0.03 psi @ 136.2 m3/h

Voltage 240 VAC / 60 Hz. / 1-phase

Rated Power (W) 700 1000 3000 3000

Electronic ballasts 1 1 1 1

UV-C power (W) 105 150 450 450

Lamps 1 1 1 1

Lifetime (hours) 3,000 5,000

Cleaning

Manual

Automatic (optional with JUVMPAUTO module)

Cooling Panel: fan + ﬁlter

Ballast: self-cooled aluminum heatsink

Control monitor

Radiation

Flow

Temperature

Lamp

3.4" TFT color touchscreen (320x240 pixels)

6 languages

UV-C sensor

Flow sensor (stainless steel)

Temperature sensor (PT-100, stainless steel)

Hour counter • • • •

Alarm log • • • •

Power control • • • •

Re-ignition control • • • •

Control inputs Two (2) potential-free contacts: ﬂow switch and remote stop

1This product has been tested to conﬁrm a minimum inactivation equivalent of 3 log (99.9%) Cryptosporidium Parvum

in accordance with NSF 50 and the US EPA UV DGM. This product has met the requirements of NSF/ANSI 50, Annex

H.1: Disinfection Efﬁcacy for the >= minimum of a 3 log (99.9%) reduction of Enterococcus Faecium [ATCC #6569] and

Pseudomonas aeruginosa [ATCC #27313]. This product is intended for secondary disinfection and should be used with

EPA registered or approved disinfection chemicals to impart residual concentrations in accordance with state and local

regulations.

Page 6

ENGLISH Jandy®UV Medium Pressure | Installation & Operation Manual

Dimensions

JUVMP 120-320 models

A B C D E G H

inch 23.6 31.5 11.8 33.0 11.0 18.7 17.7

mm 600 800 300 838 279 476 449

JUVMP 700 model

A B C D E G H

inch 23.6 31.5 11.8 40.0 16.0 17.6 18.7

mm 600 800 300 1017 406 446 475

Page 7

Jandy®UV Medium Pressure | Installation & Operation Manual ENGLISH

2.3 Product Contents

The packaging should contain the following items:

• UV reactor

• Flow sensor:

SI5004 + EVC005 cable (5 m /16.4 ft)1

• Temperature sensor:

TM 4411+ EVC005 cable (5 m /16.4 ft)1

• Radiation sensor:

UVX-SE + EVC059 cable (5 m /16.4 ft)1

• Automatic wiper driver + WPA-05 cable

(5 m /16.4 ft)1

• Control panel

• Lamp power cables LP-035 x2 (5 m /16.4 ft)1

• Operation manual

1 Custom cable lengths may be supplied on demand.

NOTE: Disposing Old Product

Please act according to local rules and do not dispose

old products with normal household waste. The correct

disposal of old product will help prevent potential

harmful effects against the environment and health.

Section 3. Installation

3.1 General Considerations

• In order to guarantee a good state of

conservation, the Jandy UV MP system must

be installed in a dry and well-ventilated place at

the technical room. The protection degree of the

system does not allow outdoor installation.

• The temperature at the installation area must be

within 32°F (0°C) and 86°F (30°C) and the relative

humidity must not exceed 80%.

• Install the unit as far away as possible from any

storage of chemical products and sources of

moisture.

WARNING

Beware of corrosive atmosphere formation due to pH decreasing

solutions (specially, those ones based on hydrochloric acid “HCl”).

Do not install the system near to any stores of these chemicals. We

strongly recommend the use of chemicals based on sodium bisulphate

or diluted sulphuric acid.

3.2 UV Reactor Installation

The reactor of HELIOX UV MP systems can be

installed both horizontally and vertically, as shown in

the recommended installation diagrams (see Figures

1 &2).

WARNING

Lamp must always remain horizontal to the ground, as if it is installed

so that the lamp is vertical, in the case of low ﬂow, an air chamber may

be formed on its top, thus becoming part of the bulb exposed. Given

the high working temperature of medium pressure lamps, it is easily

understandable that this situation should always be avoided.

If the UV reactor is installed horizontally, sensors and wiper driver must

remain in the upper part.

Observe ﬂow direction indications located on the UV chamber.

The reactor of the Jandy UV MP systems is made of

AISI 316 L stainless steel within which the UV lamp is

housed. The system should always be installed after

the ﬁltration system, and before any other device in

the installation such as heat pumps, control systems,

dosage systems, salt electrolysis systems, etc.

The installation of the UV system should allow easy

access to the UV lamp by the user. The location of

the system must have an effective dimension that

Page 8

ENGLISH Jandy®UV Medium Pressure | Installation & Operation Manual

allow the complete removal of the UV lamp from the

sleeve (approximately one meter on each side of the

connection boxes of the UV lamp).

It is highly recommended to install the Jandy UVMP

system in a place of the pipe that can be easily

isolated from the rest of the installation by two

valves, so that the tasks of maintenance can be

carried out with no need of partial or total draining of

the swimming pool. Where the system is installed on

a by-pass (recommended option), a valve to regulate

the ﬂow must be introduced.

WARNING

Prior to the installation or replacement of any system component make

sure it has been previously disconnected from the mains, and there is

no water ﬂow through it. Use only spare parts supplied by Jandy.

UV chamber grounding must be made in the two bonding lugs marked

*on the end ﬂanges using No. 8 AWG (US) and No. 6 AWG (Canada)

solid copper conductor and secured to the chamber by paint breaking

washers and nuts.

* IEC 60417, symbol 5019

1. Filter

2. Pump

3. UV reactor

4. Other equipment (dosage pumps,

controllers, heat exchangers, etc.)

Lamp Vertical

Lamp Horizontal

Floor

Figure 1. Recommended Installation — Horizontal

Page 9

Jandy®UV Medium Pressure | Installation & Operation Manual ENGLISH

5. Filter

6. Pump

7. UV reactor

8. Other equipment (dosage pumps,

controllers, heat exchangers, etc.)

Figure 2. Recommended Installation — Vertical

3.3 Control Panel Installation

• Always install the control panel of the Jandy UV

MP system vertically and on a rigid surface (wall),

so that the touchscreen located on the front panel

is level with the eyes.

• Cooling fan and grids must not be blocked.

WARNING

The equipment should be assembled and handled by truly qualiﬁed

people.

Current electrical and accident prevention regulations should be

followed.

Do not attempt to alter the system to operate at a different voltage.

Both the power of the Jandy UV MP system control

panel and the interconnection of the UV lamp and the

sensors must be made at the terminal block at the

base inside the control panel. The control panel base

has a series of cable glands for the correct ﬁxation of

the power cables and sensors. In any case the length

or section thereof should be amended, without ﬁrst

consulting a Jandy authorized technician.

WARNING

Use copper conductors only.

Permanently connected.

Page 10

ENGLISH Jandy®UV Medium Pressure | Installation & Operation Manual

3.4 Control Panel: Field Wiring Diagram

T. block Control panel input Cable Wire description

POWER 240 VAC / 50-60 Hz / 1-phase (1)

GROUND

1 PHASE

2 NEUTRAL

PE UV REACTOR BONDING (2) GROUND

3UV LAMP OUTPUT LP-035/1 RED

4 LP-035/2 RED

5 SW-11 LP-035/1 BLACK “1”

6 SW-12 BLACK “2”

7 SW-21 LP-035/2 BLACK “1”

8 SW-22 BLACK “2”

SI5004 FLOW SENSOR INPUT EVC-005

BROWN

10 WHITE

11 BLUE

UVX-SE RADIATION SENSOR INPUT EVC059

WHITE

13 BROWN

14 BLACK

15 GREY

TM4411 EVC-005

BROWN

17 WHITE

18 BLUE

19 FLOW SWITCH INPUT (3) POTENTIAL-FREE CONTACT

21 EXTERNAL STOP INPUT (4) POTENTIAL-FREE CONTACT

WIPER DRIVER (optional module) (1) WPA-05

“1” (AC) Wiper driver

(JUVMPAUTO)

24 “2” (SIGNAL)

25 “3” (GROUND)

(1) Not supplied with the unit

(2) Not supplied with the unit. Bonding must be made with a solid copper conductor minimum No. 8 AWG

(USA) / 6 AWG (Canada).

(3) Default bridged input

(4) Input logics

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Jandy Wasserfiltersystem Handbücher

Jandy

Jandy JEF-IN Bedienungsanleitung

Jandy

Jandy SFSM60 Bedienungsanleitung

Jandy

Jandy TruClear Bedienungsanleitung

Jandy

Jandy SFSM60 Bedienungsanleitung

Jandy

Jandy AquaPure Ei Series Bedienungsanleitung

Jandy

Jandy CL Versa-Plumb Bedienungsanleitung

Jandy

Jandy AquaPure Bedienungsanleitung

Jandy

Jandy JSWC40 Bedienungsanleitung

Jandy

Jandy APUREM Bedienungsanleitung

Jandy

Jandy PureLink Bedienungsanleitung

Jandy

Jandy AquaPure APURE700 Bedienungsanleitung

Jandy

Jandy CL Versa-Plumb Series Bedienungsanleitung

Jandy

Jandy AquaPure Pure700 Bedienungsanleitung

Jandy

Jandy Jandy Pro Series Bedienungsanleitung

Jandy

Jandy SFTM PRO Series Bedienungsanleitung

Jandy

Jandy JS Series Bedienungsanleitung

Jandy

Jandy SFTM22-1.5 Betriebsanleitung

Jandy

Jandy CV Versa-Plumb Series Bedienungsanleitung

Jandy

Jandy CS150 Bedienungsanleitung

Jandy

Jandy AquaPure Bedienungsanleitung

Jandy

Jandy Jandy Pro Series Bedienungsanleitung

Jandy

Jandy TruGuard Bedienungsanleitung

Jandy

Jandy APURE35PLG Bedienungsanleitung

Jandy

Jandy CJ200 Betriebsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung