Javad JLink LTE Bedienungsanleitung

All contents in this manual are copyrighted by JAVAD GNSS.

stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express

written consent from JAVAD GNSS.

JLink LTE

User Manual

Version 1.0

Last Revised October 13, 2017

www.javad.com

www.javad.com 3

Preface

Thank you for purchasing this product. The materi-

als available in this Manual (the “Manual”) have been

prepared by JAVAD GNSS, Inc. (“JAVAD GNSS”) for

owners of JAVAD GNSS products. It is designed to as-

sist owners with the use of JLink LTE and its use is

subject to these terms and conditions (the “Terms and

Conditions”).

Please read these Terms and Conditions carefully.

Terms and Conditions

USE – JAVAD GNSS products are designed to be

used by a professional. The user is expected to have

a good knowledge and understanding of the user and

safety instructions before operating, inspecting or ad-

justing. Always wear the required protectors (safety

shoes, helmet, etc.) when operating the unit.

Manual is the intellectual property of, and copyrighted

material of JAVAD GNSS. All rights are reserved. You

may not use, access, copy, store, display, create deriva-

tive works of, sell, modify, publish, distribute, or allow

any third party access to, any graphics, content, infor-

mation or data in this Manual without JAVAD GNSS’

express written consent and may only use such infor-

mation for the care and operation of your JLink LTE.

The information and data in this Manual are a valuable

asset of JAVAD GNSS and are developed by the ex-

penditure of considerable work, time and money, and

are the result of original selection, coordination and ar-

rangement by JAVAD GNSS.

TRADEMARKS – JLink LTE™, JAVAD GNSS® are

trademarks or registered trademarks of JAVAD GNSS.

Windows® is a registered trademark of Microsoft

Corporation; Bluetooth® word mark is owned by the

Bluetooth SIG, Inc. Product and company names men-

tioned herein may be trademarks of their respective

owners.

DISCLAIMER OF WARRANTY – EXCEPT

FOR ANY WARRANTIES IN THIS MANUAL OR

A WARRANTY CARD ACCOMPANYING THE

PRODUCT, THIS MANUAL AND JLINK LTE ARE

PROVIDED “AS-IS.” THERE ARE NO OTHER

WARRANTIES. JAVAD GNSS DISCLAIMS ANY

IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR ANY PARTICULAR USE OR

PURPOSE. JAVAD GNSS AND ITS DISTRIBUTORS

SHALL NOT BE LIABLE FOR TECHNICAL

OR EDITORIAL ERRORS OR OMISSIONS

CONTAINED HEREIN; NOR FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING

FROM THE FURNISHING, PERFORMANCE OR

USE OF THIS MATERIAL OR THE JLINK LTE.

SUCH DISCLAIMED DAMAGES INCLUDE BUT

ARE NOT LIMITED TO LOSS OF TIME, LOSS

OR DESTRUCTION OF DATA, LOSS OF PROFIT,

SAVINGS OR REVENUE, OR LOSS OF THE

PRODUCT’S USE. IN ADDITION, JAVAD GNSS IS

NOT RESPONSIBLE OR LIABLE FOR DAMAGES

OR COSTS INCURRED IN CONNECTION

WITH OBTAINING SUBSTITUTE PRODUCTS

OR SOFTWARE, CLAIMS BY OTHERS,

INCONVENIENCE, OR ANY OTHER COSTS. IN

ANY EVENT, JAVAD GNSS SHALL HAVE NO

LIABILITY FOR DAMAGES OR OTHERWISE TO

YOU OR ANY OTHER PERSON OR ENTITY IN

EXCESS OF THE PURCHASE PRICE FOR JLink

LTE.

LICENSEAGREEMENT – Use of any computer pro-

grams or software supplied by JAVAD GNSS or down-

loaded from a JAVAD GNSS website (the “Software”)

in connection with JLink LTE constitutes acceptance

of these Terms and Conditions in this Manual and an

agreement to abide by these Terms and Conditions. The

user is granted a personal, non-exclusive, non-trans-

ferable license to use such Software under the terms

stated herein and in any case only with a single JLink

LTE or single computer. You may not assign or transfer

the Software or this license without the express written

consent of JAVAD GNSS. This license is effective until

terminated. You may terminate the license at any time

by destroying the Software and Manual. JAVAD GNSS

may terminate the license if you fail to comply with

any of the Terms or Conditions. You agree to destroy

the Software and manual upon termination of your use

of JLink LTE. All ownership, copyright and other in-

tellectual property rights in and to the Software belong

to JAVAD GNSS. If these license terms are not accept-

able, return any unused software and manual.

CONFIDENTIALITY – This Manual, its con-

4 www.javad.com

tents and the Software (collectively, the “Condential

Information”) are the condential and proprietary in-

formation of JAVAD GNSS. You agree to treat JAVAD

GNSS’ Condential Information with a degree of care

no less stringent that the degree of care you would use

in safeguarding your own most valuable trade secrets.

Nothing in this paragraph shall restrict you from dis-

closing Condential Information to your employees

as may be necessary or appropriate to operate or care

for JLink LTE. Such employees must also keep the

Condentiality Information condential. In the event

you become legally compelled to disclose any of the

Condential Information, you shall give JAVAD GNSS

immediate notice so that it may seek a protective order

or other appropriate remedy.

WEBSITE; OTHER STATEMENTS – No statement

contained at the JAVAD GNSS website (or any oth-

er website) or in any other advertisements or JAVAD

GNSS literature or made by an employee or indepen-

dent contractor of JAVAD GNSS modies these Terms

and Conditions (including the Software license, war-

ranty and limitation of liability).

SAFETY – Improper use of JLink LTE can lead to

injury to persons or property and/or malfunction of the

product. The JLink LTE should only be repaired by au-

thorized JAVAD GNSS warranty service centers. Users

should review and heed the safety warnings.

MISCELLANEOUS – The above Terms and

Conditions may be amended, modied, superseded,

or canceled, at any time by JAVAD GNSS. The above

Terms and Conditions will be governed by, and con-

strued in accordance with, the laws of the State of

California, without reference to conict of laws.

Regulatory Information

The following sections provide information on this

product’s compliance with government regulations.

FCC Class B Compliance

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received,

including interference that may cause undesired oper-

ation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful in-

terference in residential installations. This equipment

generates, uses, and can radiate radio frequency ener-

gy, and if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause interference to radio

or television equipment reception, which can be deter-

mined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

Reorient or relocate the receiving antenna.

Move the equipment away from the JLink LTE.

Plug the equipment into an outlet on a circuit differ-

ent from that to which the unit is powered.

Consult the dealer or an experienced radio/television

technician for additional suggestions.

Any changes or modications to the equipment

not expressly approved by the party responsible for

compliance could void your authority to operate such

equipment.

Canadian Emissions Labeling

Requirements

This Class B digital apparatus meets all requirements

of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la classe B respecte toutes

les exigences du Réglement sur le matériel brouilleur

du Canada.

WEEE Directive

The following information is for EU-member states

only:

The use of the symbol indicates that this product may

not be treated as household waste. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment

www.javad.com 5

and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more

detailed information about the take-back and recycling

of this product, please contact your supplier where you

purchased the product or consult.

Screen Captures

This manual includes sample screen captures. Your

actual screen can look slightly different from the sam-

ple screen due to the unit you have connected, operat-

ing system used and settings you have specied. This is

normal and not a cause for concern.

Technical Assistance

If you have a problem and cannot nd the informa-

tion you need in the product documentation, contact

your local dealer. Alternatively, request technical sup-

port using the JAVAD GNSS World Wide Web site at:

www.javad.com

To contact JAVAD GNSS Customer Support use the

QUESTIONS button available on the www.javad.com.

6 www.javad.com

Description and Operation

Getting Started

JLink LTE is a family of devices designed for or-

ganizing a local network between different devices

via WiFi, Ethernet, and Bluetooth, connecting to the

Internet using 4G cellular digital communication ser-

vices.

Figure 1. JLink LTE

JLink LTE provides a robust solution linking the

eld GNSS equipment to RTN, where no cell phone

cover is available. JLink LTE devices may contain 1

W either UHF (406 to 470 MHz) or VHF (138-174

MHz), or ISM license free USA band (902-928 MHz)

and European CEPT license free (868-870 MHz) radio

transceiver. Marine Radiobeacon receiver (283.5 to 325

kHz) can be built-in into JLink LTE device.

JLink LTE can be congured and supported using

web-interface through Internet, and this makes the set-

up mechanism simple and accessible from anywhere in

the world.

JLink LTE LED Functionality

The table below describes the LED indicators and

device state:

www.javad.com 7

Installation

1. Connect Bluetooth and GSM antennas to JLink

LTE as shown on the picture below.

2. Connect JLink LTE to external power supply

(10…30 V).

3. Insert SIM card to the SIM card slot if you would

like to use GSM connection to connect to Internet.

Figure 2. SIM card installation

4. Plug in LAN cable if you would like to use Ethernet

connection to connect to Internet.

5. Plug in COM PORT cable if you would like to use

CLI interface to communicate with device.

Setup and Configuration

1. Turn on power of JLink LTE.

2. Wait for complete loading. When it is complete,

Power LED will blink.

3. Connect to the device and congure it using

web-browser.

Connection can be established in one o the following

ways:

• via Bluetooth interface: the device (PC, hand-

held/pad) should be with Bluetooth interface with

PAN prole support. JLink LTE Bluetooth-interface

is in visibility mode, has the name “

Jlink LTE

”

and PIN code

0000

. When connection is estab-

lished open the web-browser and enter the address

10.1.11.1:8080

• via WiFi interface: The device (PC, handheld/

pad) should be with WiFi interface. JLink LTE

WiFi-interface has the name “

Jlink LTE

” and

password “

testtest

”. When connection is estab-

lished open the web-browser and enter the address

10.1.10.1:8080.

• via Ethernet: JLink LTE LAN static IP adress is

192.168.0.200 and network mask is 255.255.255.0.

On the PC connected to the same LAN, open the web

browser and enter the address

192.168.0.200:8080

The dialog window appears with login/password re-

quest. Enter login and password (

jlink/jlink

Figure 3. Login and password entering

Thereafter the device is ready for setup and cong-

uration.

4. Select the interface which will be used to connect

to Internet and congure it. The following interfaces

are available:

• Ethernet: Congure Ethernet interface in the

Communication/LAN tab. Set the network parame-

ters and reboot the device using Reboot button in the

Administration/Management tab see gure below.

Figure 4. LAN configuration tab

• GSM/LTE/4G: Congure this interface using

Communication/GSM tab. Set the APN parameters

(if necessary) and select the SIM-card slot. In the

Communication/Power Management tab activate

the interface and wait for registering in the network

and Internet access availability. More detailed con-

nection status you can check in Status/GSM tab see

below.

8 www.javad.com

Figure 5. GSM configuration tab

• WiFi client: In the Communication/WiFi it is

necessary to switch the interface to the client mode.

In the Communication/Power Managment tab turn

the WiFi interface on. Select the network you would

like to connect in the Communication/WiFi tab, en-

ter password to get access and wait for the connec-

tion see below. More detailed connection status you

can check in Status/WiFi tab.

Figure 6. WiFi client configuration tab

• Access to Serial port via Network: In the Com-

munication/Advanced tab it is necessary to select

Serial port as Console (see gure below) and reboot

deice from Administration/Management or do pow-

er cycle. After reboot the device is ready for con-

nection to serial port CLI interface with username

“jlink” password “jLTEXXXXX” where “XXXXX”

is serial number of device which is written in device

label. For connecting to JLink LTE serial port need-

ed to setup with following parameters:

• Baudrate 115200

• Parity none

• Data Bits 8

• Stop Bits 1

• Handshake hardware

Figure 7. Advanced configuration tab

• Access to Serial port via Network:

In the Communication/Advanced tab it is necessary

to select Serial port as Network (see gure below) and

reboot device from Administration/Management or do

power cycle.

After reboot device is ready for telnet connection to

serial port using “

Ser2Net

” as login and “

jlinklte

”

as password. For connecting to JLink LTE serial port

needed to setup with following parameters:

▪ Baudrate 115200

▪ Parity none

▪ Data Bits 8

▪ Stop Bits 1

▪ Handshake hardware

Figure 8. Advanced configuration tab

www.javad.com 9

How to...

...Setup JLink LTE to provide RTK data

received via NTRIP Client to Serial Port

The following are the steps of conguration of JLink

LTE:

1. Connect to JLink LTE via web interface as de-

scribed above.

2. Congure the Cellular (GSM ):

• In the Communication/GSM tab set the PIN

code and APN parameters (if necessary);

Figure 9. JLink LTE GSM configuration tab

• Use tweezers to install or remove micro SIM

card.

• Insert the SIM card to its slot. The rst slot from

the green top cover is for micro SIM, the second

slot is for micro SD.

• In the Communication/Power Management tab

activate the GSM interface.

Figure 10. JLink LTE Power Management tab

Wait for registering in the network and Internet ac-

cess availability . Detailed connection status you can

check in Status/GSM tab.

Figure 11. JLink LTE GSM Status tab

It is possible also to connect JLink LTE to Internet

via LAN or WiFi using any WiFi router, MiFi device or

even smart-phone congured in hot spot mode.

3. Setup Serial Port. In the Communication/Advanced

tab select “Serial port as” parameter as

Terminal

. Click

“Save Setting” button and wait until nish.

Figure 12. JLink LTE Advanced tab

4. Reboot device. In the Administration/Management

tab click “Reboot” button and wait until reboot.

Figure 13. JLink LTE Administration Management tab

10 www.javad.com

5. Setup Router. In the Setup/Router tab select fol-

lowing parameters “NTRIP Client” as Source and

“Serial port“ as Destination. Click “Save Setting” but-

ton and wait until nish.

Figure 14. JLink LTE NTRIP Data Router tab

6. Setup NTRIP Client. In the Services/NTRIP tab set

following parameters: “Server name/address”, “Port”,

“User” , “Password” .

Figure 15. JLink LTE NTRIP configuration tab

• Click “Save Setting” button and wait until nish.

• Click ‘”Update” button and select “Mountpoint” .

• Click “Save Setting” button and wait until nish.

Detailed connection status you can check in Status/

NTRIP tab:

Figure 16. JLink LTE Status NTRIP tab

7. Connect Serial Port. se any application to connect

serial port of JLink LTE with following parameters:

▪ Baudrate 115200

▪ Parity none

▪ Data Bits 8

▪ Stop Bits 1

▪ Handshake hardware

...Setup JLink LTE to provide RTK data

received via UHF channel (in Satel mode) to

Serial Port

The following are the steps of conguration of JLink

LTE:

1. Connect to JLink LTE via web interface as de-

scribed above.

2. UHF conguration in Satel mode:

◦ In the Communication/UHF Int. tab:

• select operating frequency or add new frequen-

cy to the list

• select Protocol type Satel

• select channel bandwidth (spacing) either 25.0

or, 20.0, or 12.5 kHz

• verify FEC (Forward Error Correction) state is

correct

Andere Handbücher für JLink LTE

Inhaltsverzeichnis

Andere Javad Netzwerk-Router Handbücher

Javad

Javad JLink LTE Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise