JB Systems PlanoSpot 7TC Bedienungsanleitung

ENGLISH OPERATION MANUAL

JB SYSTEMS®1/65 PLANO SPOT 7TC

OPERATION MANUAL

Thank you for buying this JB Systems®product. To take full advantage of all possibilities and for your own

safety, please read these operating instructions very carefully before you start using this unit.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the current European and

national guidelines. Conformity has been established and the relevant statements and documents have been

deposited by the manufacturer.

This device was designed to produce decorative effect lighting and is used in light show systems.

Super compact RGB LED-projector containing 7pcs high power RGB 3Watt LEDs

Same functionality and form factor as Plano Spot based on 5mm but much brighter!

Beam angle = 25° (medium spot)

Many applications possible: Discotheques, DJs, exhibition booths, homes, ...

Can be fixed in ALU-truss like any standard LED PAR, using a standard clamp

Can be used as floor projector, under any possible projection angle

Super compact housing, perfect for hiring companies!

Very smooth RGB color changes thanks to high freq. dimming electronics

Different working modes:

Standalone: custom colors selectable or automatic and beat synchronized color changes

Master/slave mode: up to 16 units can be used together for wonderful preprogrammed, music

synchronized lightshows. (optional CA-8 controller possible)

DMX-controlled: 4modes, 4channels (R, G, B + Dimmer/strobe/sound chase)

Controlled by LEDCON-02 DJ-controller

Different ways to set DMX start address:

Fast remote DMX addressing using any standard DMX-controller.

In master/slave mode you can address all units automatically.

IEC mains in/outputs: easy daisy chaining of several units.

BEFORE USE

Before you start using this unit, please check if there’s no transportation damage. Should there be any, do

not use the device and consult your dealer first.

Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary

for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused

by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects

or problems caused by disregarding this user manual.

Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user

manual.

Check the contents:

Check that the packing contains the following items:

Operating instructions

PLANO SPOT 7TC

Hanging bracket

2 Knobs to fasten the hanging bracket

ENGLISH OPERATION MANUAL

JB SYSTEMS®2/65 PLANO SPOT 7TC

SAFETY INSTRUCTIONS:

To protect the environment, please try to recycle the packing material as much as possible.

To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or may even cause damages.

This unit is for indoor use only.

Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign

object enters the unit, immediately disconnect the mains power.

Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture

must be fixed at least 50cm from surrounding walls.

Don’t cover any ventilation openings as this may result in overheating.

Prevent use in dusty environments and clean the unit regularly.

Keep the unit away from children.

Inexperienced persons should not operate this device.

Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

Allow the device about 10 minutes to cool down before to start servicing.

Always unplug the unit when it is not used for a longer time or before to start servicing.

The electrical installation should be carried out by qualified personal only, according to the regulations for

electrical and mechanical safety in your country.

Check that the available voltage is not higher than the one stated on the unit.

The power cord should always be in perfect condition. Switch the unit immediately off when the power cord

is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Never let the power-cord come into contact with other cables!

This fixture must be earthed in order to comply with safety regulations.

Don’t connect the unit to any dimmer pack.

Always use an appropriate and certified safety cable when installing the unit.

In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.

Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same

type and electrical specifications!

In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

The housing and the lenses must be replaced if they are visibly damaged.

CAUTION: To reduce the risk of electric shock, do not remove

the top cover. No user-serviceable parts inside. Refer servicing

to qualified service personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the

use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence

of important operation and maintenance (servicing) instructions in the literature accompanying

this appliance.

This symbol means: indoor use only

This symbol means: Read instructions

This symbol means: Safety Class I appliance

This symbol determines: the minimum distance from lighted objects. The minimum distance

between light-output and the illuminated surface must be more than 1 meters

The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for

mounting on non-combustible surfaces)

CAUTION: Do not stare at operating lamp.

May be harmful to the eyes.

ENGLISH OPERATION MANUAL

JB SYSTEMS®3/65 PLANO SPOT 7TC

Please use the original packing when the device is to be transported.

Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering

from epilepsy.

DESCRIPTION:

1. Front with hard plastic cover to protect the

5mm LEDs.

2. Hanging bracket with knobs on both sides to

fasten the unit and a mounting hole to fix a

mounting hook.

3. ¼” jack used to connect the optional CA-8

controller

4. Mains input with IEC socket and integrated

fuse holder, connect the supplied mains cable

here.

5. Mains output with IEC socket: you can use a

special IEC power cable to connect this output

with the mains input of the next PLANO SPOT

for easier linking. (max 40 units can be linked)

6. DMX-output connector

7. DMX-input connector

8. Slave LED: is lit when the unit is in slave

mode

9. Sound LED: blinks to the rhythm of the music

while the unit is in audio mode

10. DMX LED: is lit when the unit receives a

DMX-signal

11. Master LED: is lit when the unit is switched as

master

12. MENU button: used to select the different

menu items

13. DOWN button: to go back in the menu and to lower the values shown on the display.

14. UP button: to go up in the menu and to increase the values shown on the display.

15. ENTER button: used to confirm your choice.

16. DISPLAY shows the various menus and the selected functions.

ELECTRICAL INSTALLATION

Important: The electrical installation should be carried out by qualified personal only,

according to the regulations for electrical and mechanical safety in your country.

Electrical installation for 1 standalone unit:

Insert the mains cable. The unit starts working immediately in the last selected stand-alone mode.

Refer to chapter HOW TO SETUP to learn how to switch between static and sound mode.

Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.

Electrical installation for two or more units in master/slave:

Connect 2 to maximum 16 units together using good quality balanced microphone cables. The unit that

has no cable connected to its DMX-input is the “master”, the others are the slave units.

Make sure that all units are connected to the mains.

Refer to chapter HOW TO SETUP for more information.

Done!

Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control

over the master/slave operation. You can also connect the LEDCON 02 remote controller

ENGLISH OPERATION MANUAL

JB SYSTEMS®4/65 PLANO SPOT 7TC

Electrical installation for two or more units in DMX-mode:

The DMX-protocol is a widely used

high speed signal to control intelligent

light equipment. You need to “daisy

chain” your DMX controller and all the

connected units with a good quality

balanced cable.

To prevent strange behavior of the

light effects, due to interferences, you

must use a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter

cables, this simply won’t work!

Make sure that all units are connected to the mains.

Each light effect in the chain needs to have its proper start address so it knows which

commands from the controller it has to decode. In the section HOW TO SETUP you

will learn how to set the DMX addresses. Remember that each projector uses 4 channels, a possible

address setup could be: unit1 = 001 ~ unit2 = 005 ~ unit3 = 009 ~ unit4 = 013 ~ etc.

OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only. Improper

installation can result in serious injuries and/or damage to property. Overhead rigging requires

extensive experience! Working load limits should be respected, certified installation materials

should be used, the installed device should be inspected regularly for safety.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

The device should be installed out of reach of people and outside areas where persons may walk by or be

seated.

Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s

weight.

Always use a certified safety cable that can hold 12times the weight of the

device when installing the unit. This secondary safety attachment should

be installed in a way that no part of the installation can drop more than

20cm if the main attachment fails.

The device should be well fixed; a free-swinging mounting is dangerous

and may not be considered!

Don’t cover any ventilation openings as this may result in overheating.

The operator has to make sure that the safety-relating and machine-

technical installations are approved by an expert before using them for the

first time. The installations should be inspected every year by a skilled

person to be sure that safety is still optimal.

HOW TO SETUP:

MAIN MENU:

To select any of the menu options, press the MENU button up to when the required option is shown on the

display.

Select the function with the ENTER button. The display will blink.

Use DOWN and UP button to choose the desired menu option.

Once the required menu option is selected, press the ENTER button to select.

Remark: Press the MENU button for about 2 seconds to return to running mode or just wait 8 seconds.

DMX512 Address Setting

Used to set the start address in a DMX setup, you can also automatically program the next PLANO

SPOT projectors in the same DMX-chain.

Program a DMX start address in 1 unit:

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP buttons to change the DMX512 address.

ENGLISH OPERATION MANUAL

JB SYSTEMS®5/65 PLANO SPOT 7TC

Once the correct address is shown on the display, press

the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to

running mode.

Automatically program the DMX start addresses of several units

in a DMX-chain:

Connect the DMX in/outputs of all projectors together and

switch them all on

On the first unit in the chain:

Press the MENU button until is shown on the

display.

Press the ENTER button to select.

Use DOWN and UP buttons to change the DMX512

address.

Once the correct address shows on the display, press

2 times the ENTER button.

After this, use the DOWN and UP buttons until

is shown on the display.

Press the ENTER button to start the automatic

programming all units flash one time to indicate that

the addresses are automatically set, starting from the

address programmed in the first unit.

Press the MENU button on the first unit for about 2

seconds to return to running mode.

Example: the first projector was set to DMX-address 100

when you perform the automtic addressing, the other

projectors in the DMX-chain will receive addresses: 104,

108, 112, 116, …

Channel Mode

The unit has 4 different channel modes, each with different

functions for the 4th channel. Refer to the DMX-chart to see

the differences.

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP button to select one of the available

channel modes.

Once the mode is selected, press the ENTER button to

confirm.

Press the MENU button for about 2 seconds to return to

running mode.

Show Mode

Used to choose to select one of the preprogrammed multi

channel shows when used in standalone or master/slave

mode.

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP buttons to select one of the

preprogrammed shows:

all shows played in random mode.

to 12 different built-in shows.

Except for the random show (Show 0) you will also be asked to

select a running speed for the static mode. With the UP/DOWN

buttons you can select (slow) to (fast).

Once the right show is selected, press the ENTER button to

confirm.

ENGLISH OPERATION MANUAL

JB SYSTEMS®6/65 PLANO SPOT 7TC

Press the MENU button for about 2 seconds to return to running mode.

Color chase Mode

Used to choose to select one of the preprogrammed colorfades when used in standalone or

master/slave mode. All projectors will always show an identical output.

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP buttons to select one of the preprogrammed shows

You will also be asked to select a running speed for the static mode. With the UP/DOWN buttons you can

select (slow) to (fast).

Once the right show is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

Slave Mode

By choosing the right slave mode you can improve the impact of the multi-channel shows.

The first slave should be in “SL 2” mode, the second in “SL 3” mode, etc. until “SL16”.

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP button to select one of the available slave modes.

Once the right mode is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

Sound Mode

Used to choose the desired sound mode to trigger the shows.

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP button to select one of the available modes:

(sound mode ON) the shows are triggered by the internal microphone.

(sound mode OFF) the shows are triggered by the speed selected with the shows.

Once the right mode is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

Blackout Mode

Blackout mode: when no DMX-signal is detected, the unit goes in blackout.

No blackout mode: when no DMX-signal is detected, the unit automatically switches to master mode.

ALWAYS set to “No Blackout” when the unit is used in standalone or master (master/slave) mode!!!

Press the MENU button until is shown on the display.

Press the ENTER button.

Use DOWN and UP button to select YES (blackout) or no (no blackout) mode.

Once the mode is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

Color Preset Mode

Used to choose one of the 16 standard preset colors. You can also define your own custom color,

based on individual settings for red, green and blue.

Press the MENU button until is shown on the display.

Press the ENTER button to select.

Use DOWN and UP button to select one of the available options:

Select one of the preset colors to and press ENTER to confirm.

Select to make your own color and press ENTER to confirm. Now you can set the 3 colors to

make your own custom color:

(red):press ENTER. Then use the DOWN and UP buttons to set the value between 000

and 255. Confirm with the ENTER button. Use the DOWN and UP buttons to select the next color.

(green):press ENTER. Then use the DOWN and UP buttons to set the value between 000

and 255. Confirm with the ENTER button. Use the DOWN and UP buttons to select the next color.

ENGLISH OPERATION MANUAL

JB SYSTEMS®7/65 PLANO SPOT 7TC

(blue):press ENTER. Then use the DOWN and UP buttons to set the value between 000

and 255. Confirm with the ENTER button. Use the DOWN and UP buttons to select the next color.

Once the right settings are done; press the MENU button for about 2 seconds to return to running mode.

Led Display

Display on: display is always on.

Display off: display is off when not used.

Press the MENU button until the display shows .

Press the ENTER button.

Use DOWN and UP buttons to select (display always on) or (display off when not used).

Once the mode is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

Display Inversion

Display inversion: display is readable when the unit is mounted upside down.

Press the MENU button until the display shows

Press the ENTER button, the display starts blinking.

Use DOWN and UP buttons to select (display inversion) or (normal display).

Once the mode is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

Fixture Temperature

Press the MENU button until the display shows .

Press ENTER button and the display will show the temperature of the unit.

To go back to the functions press the MENU button again.

Adjust White balance

Makes it possible to adjust the white color when all colors are at maximum.

Press the MENU button until is shown on the display.

Press the ENTER button, the display starts blinking.

Use the DOWN and UP button to select the (Red) or (Green) or (Blue) color.

Press the ENTER button, the display starts blinking.

Use the DOWN and UP button to adjust the value from 125 to 255 and press ENTER to confirm.

Once the mode has been selected, press the ENTER button to confirm.

To go back to the main menu without any change press the MENU button shortly.

If you want to go back to normal running mode: press the MENU button for about 2 seconds.

Fixture Hours

Used to show the number of working hours of the unit.

Press the MENU button until is shown on the display.

Press the ENTER button to show the number of working hours in the display.

Press the MENU button for about 2 seconds to return to running mode.

Software version:

Used to show the software version of the unit.

Press the MENU button until is shown on the display.

Press the ENTER button to show the software version of the unit.

Press the MENU button for about 2 seconds to return to running mode.

ENGLISH OPERATION MANUAL

JB SYSTEMS®8/65 PLANO SPOT 7TC

Remote addressing

In some rare cases (caused by interferences from other appliances) remote addressing can

accidentally be activated. To avoid this the remote addressing feature can be switched off.

ON: remote addressing is active (default mode)

OFF: remote addressing is de-activated to solve the problem.

Press the MENU button until the display shows .

Press the ENTER button.

Use DOWN and UP buttons to select or .

Once the mode is selected, press the ENTER button to confirm.

Press the MENU button for about 2 seconds to return to running mode.

OPERATING INSTRUCTIONS

A. Standalone 1unit:

Just connect the projector to the mains.

Select one of the automatic modes or select a fixed color

Select the static or sound control mode

Don’t forget to set the Blackout mode to ‘NO Blackout’ or nothing will happen.

Refer to chapter HOW TO SETUP to learn how to make the previous settings.

Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.

B. Two or more units in master/slave setup:

Connect 2 to maximum 16 units together. Refer to the chapter “electrical installation” to learn how to

do this.

Set the slave mode for each projector: the first one must be set on Master and each slave projector

can be set to its specific slave mode (see chapter HOW TO SETUP the slave mode)

Connect all units to the mains and put on some music. The units will start working automatically to the

rhythm of the music and show the internal chase programs.

Don’t forget to set the Blackout mode to ‘NO Blackout’ or nothing will happen.

Remark: You can connect a CA-8 or LEDCON-02 remote controller to the master unit if you want to

have more control over the master/slave operation.

C. Connect the optional CA-8 controller for more control:

The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the

CA-8 input of the first unit (master). Now you can control all the connected units:

BUTTON

ACTIONS

STANDBY

To blackout all the fixtures

FUNCTION

1.Synchronous strobe

in white color

2.The same color

chase

3.Different color

strobe

Select one of the

different colors.

Select one of the 12

different multi-channel

shows.

Select one of the

different color fade

modes.

MODE

Strobe

(LED OFF)

Color select

(LED ON)

Show select

(LED slow blinking)

Chase select

(LED fast blinking)

D. Connect an optional LEDCON-02 controller for more control:

The LEDCON-02 controller can only be used in standalone or master/slave mode. Connect the controller

to the DMX-input of the first unit (master). Make sure that the PLANO SPOT projectors are all set to

channel mode1 (Md 1). Now you can control all the connected units in 4 or 8channel mode. Refer to the

user manual of the LEDCON-02 controller for more information and automatic addressing.

Inhaltsverzeichnis

Sprachen:

Andere JB Systems DJ-Equipment Handbücher

JB Systems

JB Systems beat 6 mk2 Bedienungsanleitung

JB Systems

JB Systems PARTY BEAMS Bedienungsanleitung

JB Systems

JB Systems MULTIBEAM LASER Bedienungsanleitung

JB Systems

JB Systems ALIEN Bedienungsanleitung

JB Systems

JB Systems CLUBSPOT Installationshandbuch

JB Systems

JB Systems Dj-kontrol 3 Bedienungsanleitung

JB Systems

JB Systems CD 410 Bedienungsanleitung

JB Systems

JB Systems LIVESET 2 Bedienungsanleitung

JB Systems

JB Systems LED Rave Bedienungsanleitung

JB Systems

JB Systems Sunbar Combi Bedienungsanleitung

JB Systems

JB Systems YETI Installationshandbuch

JB Systems

JB Systems INTRUDER Bedienungsanleitung

JB Systems

JB Systems LED Rotogobo Bedienungsanleitung

JB Systems

JB Systems RAVE SPOT Bedienungsanleitung

JB Systems

JB Systems enh2.3 Mk2 Bedienungsanleitung

JB Systems

JB Systems UV-400 Bedienungsanleitung

JB Systems

JB Systems PIXEL PIPE Bedienungsanleitung

JB Systems

JB Systems BL-B18 Bedienungsanleitung

JB Systems

JB Systems Sunbar White Bedienungsanleitung

JB Systems

JB Systems PARTY SPOT Installationshandbuch

JB Systems

JB Systems USB DERBY Bedienungsanleitung

JB Systems

JB Systems BEAT6 Mk2 Bedienungsanleitung

JB Systems

JB Systems RAVE BAR Bedienungsanleitung

JB Systems

JB Systems Liverack-10 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung

Chauvet

Chauvet ovation B-2805FC Bedienungsanleitung