JB Systems YETI Installationshandbuch

ENGLISH OPERATION MANUAL

JB SYSTEMS®1/4 YETI

OPERATION MANUAL

Thank you for buying this JB Systems®product. To take full advantage of all possibilities and for your own

safety, please read these operating instructions very carefully before you start using this unit.

FEATURES

Powerful 1200W snow machine.

Produces large amounts of artificial snow flakes.

Adjustable snow output volume:

via the wired remote control (included)

via the wireless remote control (included)

Recommended Fluid: JB Systems Snow Liquid

BEFORE USE

Before you start using this unit, please check if there’s no transportation damage. Should there be any, do

not use the device and consult your dealer first.

Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary

for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused

by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects

or problems caused by disregarding this user manual.

Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user

manual.

Check the contents:

Check that the carton contains the following items:

Operating instructions

YETI snow machine

Hanging bracket + with 2 knobs and 2 rubber rings (put the rings between the bracket and the machine).

Wired remote controller

Wireless remote controller

Wireless remote receiver

SAFETY INSTRUCTIONS:

CAUTION: To reduce the risk of electric shock, do not remove the top cover.

No user-serviceable parts inside. Refer servicing to qualified service

personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use

or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence of

important operation and maintenance (servicing) instructions in the literature accompanying this

appliance.

This symbol means: indoor use only.

This symbol means: Read instructions.

This symbol determines: the minimum distance from objects. The minimum distance between fogger

output and objects must be more than 1 meter.

To protect the environment, please try to recycle the packing material as much as possible.

To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or may even cause damages.

This unit is for indoor use only.

CAUTION

ENGLISH OPERATION MANUAL

JB SYSTEMS®2/4 YETI

Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign

object enters the unit, immediately disconnect the mains power.

Locate the unit in a well ventilated spot, away from any flammable materials and/or liquids.

Don’t cover any ventilation openings as this may result in overheating.

Prevent use in dusty environments and clean the unit regularly.

Keep the unit away from children.

Inexperienced persons should not operate this device.

Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.

Make sure to always place the unit on a stable surface.

Always unplug the unit when it is not used for a longer time or before you start servicing.

Check that the available voltage is not higher than the one stated on the rear panel of the unit.

The power cord should always be in perfect condition. Switch the unit immediately off when the power cord

is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Never let the power-cord come into contact with other cables!

This unit must be earthed in order comply with safety regulations.

In order to prevent electric shock, do not open the cover.

Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same

type and electrical specifications!

In the event of serious operating problems, stop using the unit and contact your dealer immediately.

The housing must be replaced if it is visibly damaged.

Please use the original packing when the device is to be transported.

Due to safety reasons it is prohibited to make unauthorized modifications to

the unit.

DESCRIPTION:

1. OUTPUT: with this knob you can select the speed of the fan.

2. WIRELESS REMOTE INPUT: Used to connect the supplied wireless

remote control receiver.

3. WIRED REMOTE INPUT: Used to connect the supplied wired remote

controller.

4. POWER SWITCH: Used to switch the power of the unit on/off.

5. INPUT FUSE: When the fuse is blown, first locate and solve the problem

that caused the fuse to blow. When the problem is solved, replace a

damaged fuse with a fuse of the same type and electrical specifications.

(250V-8A)

6. MAINS CABLE: to be plugged in a mains wall socket with earth

connection.

REMOTE CONTROLLER:

1. [OUTPUT] KNOB: this knob is used to set the output volume.

Turn the knob clockwise to increase the output

Turn the knob counterclockwise to decrease the ouput

2. [POWER] LED: when the unit is on, this Led will be lit.

3. [READY] LED: when the fan is switched on by the on/off button, this LED will be lit.

4. [ON/OFF] BUTTON: used to switch the fan on or off

ENGLISH OPERATION MANUAL

JB SYSTEMS®3/4 YETI

OPERATING INSTRUCTIONS

Put the snow machine on a flat and very stable surface.

Make sure the liquid tank is not empty. Always use good quality snow liquid to fill up the tank. Close the

tank immediately to prevent dirt to enter the reservoir!

Plug the supplied wired remote or the wireless remote receiver in the corresponding remote control input

on the back of the unit.

Make sure to plug the snow machine in a mains wall socket with earth connection

Switch the snow machine on.

WARNING: NEVER use the machine with an empty reservoir. This can damage the pump !

Used with the supplied wired remote controller:

Connect the special 5pin connector of the controller to the [WIRED REMOTE] input on the back of the

snow machine.

Use the [ON/OFF] button of the remote controller to start/stop the fan.

On the back of the unit, you can select the speed of this fan [High] or [Low]

Use the round button to set the output volume of the pump.

Used with the supplied wireless remote controller:

Connect the special 5pin connector of the wireless remote

receiver to the [WIRELESS REMOTE] input on the back of

the snow machine.

Fix the remote receiver with its magnetic surface to the

snow machine.

Pull out the antenna of the wireless remote controller.

This are the functions of the 4 buttons:

Button A: Decrease Output Volume

(5 steps of 20%)

Button B: Fan OFF

Button C: Increase Output Volume

(5 steps of 20%)

Button D: Fan ON

To produce artificial snow, fan + pump volume should be

both on

OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only. Improper

installation can result in serious injuries and/or damage to property. Overhead rigging requires

extensive experience! Working load limits should be respected, certified installation materials

should be used, the installed device should be inspected regularly for safety.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids.

The device should be installed out of reach of people and outside areas where persons may walk by or be

seated.

Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s

weight.

Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit.

This secondary safety attachment should be installed in a way that no part of the installation can drop

more than 20cm if the main attachment fails.

The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!

Don’t cover any ventilation openings as this may result in overheating.

The operator has to make sure that the safety-relating and machine-technical installations are approved by

an expert before using them for the first time. The installations should be inspected every year by a skilled

person to be sure that safety is still optimal.

ENGLISH OPERATION MANUAL

JB SYSTEMS®4/4 YETI

MAINTENANCE

IMPORTANT:

Clean the machine after use and before long term storage.

Empty the tank or replace it by an empty spare tank.

To remove the deposit in a tank, rinse it with distilled water including 20% of white vinegar. Don’t run

the machine with this vinegar solution !

When the tank is clean, fill it up with distilled water and activate the machine. This will remove the

remaining snow fluid from the internal circuit and the pump.

During inspection the following points should be checked:

All screws used for installing the device and any of its parts should be tightly fastened and may not be

corroded.

Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any

deformation.

The mains cables must be in impeccable condition and should be replaced immediately when even a

small problem is detected.

Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!

SPECIFICATIONS

This unit is radio-interference suppressed. This product meets the requirements of the current European and

national guidelines. Conformity has been established and the relevant statements and documents have been

deposited by the manufacturer.

This device has been designed to produce decorative effect lighting and is used in light show systems.

Mains Input: AC 230V, 50Hz

Power consumption: 1200 Watt

DMX Channels: No DMX on board

Fuse: T8A/250V (slow blow 6x30mm)

Tank size: 5 L

Recommended Fluid: JB Systems Snow Liquid

Size: 530 x 260 x 320 mm (without hanging bracket)

Weight: 8.70 kg

All the information is subject to change without prior notice

You can download the latest version of this user manual on our website: www.jb-systems.eu

Inhaltsverzeichnis

Andere JB Systems DJ-Equipment Handbücher

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

JB Systems

JB Systems INTRUDER Bedienungsanleitung

JB Systems

JB Systems USB DERBY Bedienungsanleitung

JB Systems

JB Systems MCD 150 Bedienungsanleitung

JB Systems

JB Systems Sunbar Combi Bedienungsanleitung

JB Systems

JB Systems DELUSION Bedienungsanleitung

JB Systems

JB Systems USB PARTYSET Bedienungsanleitung

JB Systems

JB Systems CLUB7USB Bedienungsanleitung

JB Systems

JB Systems CD 100 Bedienungsanleitung

JB Systems

JB Systems CHALLENGER BSW Bedienungsanleitung

JB Systems

JB Systems USB MUSHROOM Bedienungsanleitung

JB Systems

JB Systems RAVE BAR Bedienungsanleitung

JB Systems

JB Systems Dj-kontrol 3 Bedienungsanleitung

JB Systems

JB Systems ALIEN Bedienungsanleitung

JB Systems

JB Systems CLUBSPOT Installationshandbuch

JB Systems

JB Systems MIX6 USB Bedienungsanleitung

JB Systems

JB Systems UV-400 Bedienungsanleitung

JB Systems

JB Systems BEAT6 Mk2 Bedienungsanleitung

JB Systems

JB Systems BL-B18 Bedienungsanleitung

JB Systems

JB Systems Liverack-10 Bedienungsanleitung

JB Systems

JB Systems Led Globe Bedienungsanleitung

JB Systems

JB Systems PARTY SPOT Installationshandbuch

JB Systems

JB Systems SPYDER-RGB LASER Bedienungsanleitung

JB Systems

JB Systems mix 3 USB Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung

Chauvet

Chauvet ovation B-2805FC Bedienungsanleitung