JBL Bar 5.1 Surround Bedienungsanleitung

BAR 5.1 SURROUND

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

Verify Line Voltage Before Use

The JBL Bar 5.1 Surround (soundbar and subwoofer) has been

designed for use with 100-240 volt, 50/60 Hz AC current.

Connection to a line voltage other than that for which your

product is intended can create a safety and re hazard and may

damage the unit. If you have any questions about the voltage

requirements for your specic model or about the line voltage in

your area, contact your retailer or customer service representative

before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord supplied

with your unit. We do not recommend that extension cords be

used with this product. As with all electrical devices, do not run

power cords under rugs or carpets, or place heavy objects on

them. Damaged power cords should be replaced immediately

by an authorized service center with a cord that meets factory

specications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always

pull the plug; never pull the cord. If you do not intend to use this

speaker for any considerable length of time, disconnect the plug

from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product.

Opening the cabinet may present a shock hazard, and any

modication to the product will void your warranty. If water

accidentally falls inside the unit, disconnect it from the AC power

source immediately, and consult an authorized service center.

www.jbl.com

English

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS 2

1. INTRODUCTION 4

2. WHAT’S IN THE BOX 4

3. PRODUCT OVERVIEW 5

3.1 SOUNDBAR 5

3.2 SUBWOOFER 6

3.3 REMOTE CONTROL 6

4. PLACE 7

4.1 DESKTOP PLACEMENT 7

4.2 WALL-MOUNTING 7

5. CONNECT 8

5.1 TV CONNECTION 8

5.2 DIGITAL DEVICE CONNECTION 8

5.3 CONNECTION WITH YOUR HOME NETWORK 8

5.4 BLUETOOTH CONNECTION 9

6. PLAY 10

6.1 POWER-ON/AUTO STANDBY/AUTO WAKEUP 10

6.2 FIRST-TIME SETUP 11

6.3 PLAY FROM THE TV SOURCE 11

6.4 PLAY FROM THE HDMI IN SOURCE 12

6.5 PLAY FROM THE BLUETOOTH SOURCE 12

6.6 PLAY THROUGH CHROMECAST 12

6.7 PLAY THROUGH AIRPLAY 12

7. SOUND SETTINGS 13

8. RESTORE FACTORY SETTINGS 14

9. SOFTWARE UPDATE 14

10. RE-CONNECT THE SUBWOOFER 15

11. PRODUCT SPECIFICATIONS 15

12. TROUBLESHOOTING 16

13. TRADEMARKS 17

14. OPEN SOURCE LICENSE NOTICE 18

1. INTRODUCTION

Thank you for purchasing the JBL Bar 5.1 Surround (soundbar

and subwoofer) which is designed to bring an extraordinary sound

experience to your home entertainment system. We encourage

you to take a few minutes to read through this manual, which

describes the product and includes step-by-step instructions for

setting up and getting started.

This product may have an important software update

available. Please follow the instructions to connect the

product to the Internet to ensure that your product has the

latest updates.

Designs and specications are subject to change without notice.

If you have any questions about the soundbar, installation or

operation, please contact your retailer or customer service

representative, or visit our website: www.jbl.com.

2. WHAT’S IN THE BOX

Unpack the box carefully and ensure that the following parts are

included. If any part is damaged or missing, do not use it and

contact your retailer or customer service representative.

Sound bar

Subwoofer

Remote control (with 2 AAA batteries)

Power cord*

x 2

* Power cord quantity and plug type vary region.

www.jbl.com

English

HDMI cable

Wall-mounting kit

Product information & wall-mounting template

3. PRODUCT OVERVIEW

3.1 Soundbar

Controls

1 42 3

1) (Power)

• Switch on or to standby

2) -/+ (Volume)

• Decrease or increase the volume

• Press and hold to decrease or increase the volume

continuously.

• Press the two buttons together to mute or unmute.

3) Microphone

• For audio calibration (Automatic Multibeam Calibration

(AMC))

4) (Source)

• Select a sound source: TV (default, for TV connection

where the connector is prioritized

over the connector), Bluetooth or HDMI IN

5) Status display

Rear connectors

1 2 3 4 5 6

• Connect to power (with the supplied power cord)

• USB connector for software update

• Connect to a USB storage device for MP3 le playback

(for US version only)

• Connect to the optical output on your TV or digital device

• Connect to your home network through an Ethernet

cable

• Connect to the HDMI ARC input on your TV

• Connect to the HDMI output on your digital device

3.2 Subwoofer

• Connection status indicator

Solid white Connected to the soundbar

Fast ashing white Pairing mode

Slow ashing white Reconnecting or exiting the

pairing mode

Solid amber Standby mode

• Connect to power (with the supplied power cord)

3.3 Remote control

• Switch on or to standby

• Select the TV source (for TV connection where the

connector is prioritized over the

connector)

3) (Bluetooth)

• Select the Bluetooth source

• Press and hold to connect another Bluetooth device

• Select the bass level for subwoofer: low, middle (default),

or high

5) HDMI

• Select the source

6) + / -

• Increase or decrease the volume

• Press and hold to increase or decrease the volume

continuously.

7) (Mute)

• Mute/unmute

www.jbl.com

English

4. PLACE

4.1 Desktop placement

Place the soundbar and subwoofer on a at and stable surface.

Make sure that the subwoofer is at least 3 ft (1 m) away from the

soundbar, and 4” (10 cm) away from the wall.

> 10cm/4”

1m/3ft

NOTES:

−The power cord shall be properly connected to power.

−Do not place any objects on the top of the soundbar or subwoofer.

−Make sure that the distance between the subwoofer and the soundbar

is less than 20 ft (6 m).

4.2 Wall-mounting

≤8 mm/

0.31"

4mm/

0.16"

1c)

>2” (50mm) 1a)

≥30 mm/1.18"

1b)

1. Preparation:

a) With a minimum distance of 2” (50mm) from your TV, stick

the supplied wall-mounting template to a wall by using

adhesive tapes.

b) Use your ballpen tip to mark the screw holder location.

Remove the template.

c) On the marked location, drill a 4 mm/0.16” hole.

2. Install the support for wall-mounting bracket.

3. With the screw, fasten the wall-mounting bracket onto the

bottom of the soundbar.

4. Mount the soundbar.

NOTES:

−Make sure that the wall can support the weight of the soundbar.

−Install on a vertical wall only.

−Avoid a location under high temperature or humidity.

−Before wall-mounting, make sure that cables can be properly

connected between the soundbar and external devices.

−Before wall-mounting, make sure that the soundbar is unplugged from

power. Otherwise, it may cause an electric shock.

5. CONNECT

5.1 TV connection

Connect the soundbar with your TV through the supplied HDMI

cable or an optical cable (sold separately).

Through the supplied HDMI cable

An HDMI connection supports digital audio and video with a

single connection. HDMI connectivity is the best option for your

soundbar.

HDMI (ARC)

HDMI OUT

(TV ARC)

1. Connect the soundbar with your TV by using the supplied

HDMI cable.

2. On your TV, check that HDMI-CEC and HDMI ARC have been

enabled. Refer to the owner’s manual of your TV for more

information.

NOTES:

−Full compatibility with all HDMI-CEC devices is not guaranteed.

−Contact your TV manufacturer if you have problems with the HDMI-

CEC compatibility of your TV.

Through an optical cable

OPTICAL

• Connect the soundbar with your TV by using an optical cable

(sold separately).

5.2 Digital device connection

1. Make sure that you have connected your TV to the soundbar

through the HDMI ARC connection (See “Through the supplied

HDMI cable” under “TV connection” in the “CONNECT”

chapter).

2. Use an HDMI cable (V2.0 or later) to connect the soundbar

with your digital device, such as a set-top box, DVD/Blu-ray

player or game console.

3. On your digital device, check that HDMI-CEC has been

enabled. Refer to the owner’s manual of your digital device for

more information.

HDMI IN

HDMI OUT

(TV ARC)

HDMI OUT

HDMI (ARC)

NOTES:

−* The HDMI cable is sold separately.

−Contact your digital device manufacturer if you have problems with the

HDMI-CEC compatibility of your digital device.

−When both HDMI ARC and optical cables are connected to the

soundbar, the audio output of HDMI ARC connection is prioritized.

5.3 Connection with your home network

Through Wi-Fi or an Ethernet cable, connect the soundbar to your

home network. With Chromecast built-in and Airplay supported,

the soundbar allows you to stream audio on smartphones or

tablets through the soundbar speakers.

1. On the soundbar, enter the Wi-Fi setup mode:

• Press to switch on (See “Power-on/Auto standby/Auto

wakeup” in the “PLAY” chapter).

→If the soundbar has not been connected to a network,

the screen shows “ ” and then, “ ”.

• To re-enter the Wi-Fi setup mode, press and hold until

“” is displayed.

2. On your Android or iOS device, add the soundbar to your

home Wi-Fi network.

Through the Google Home app

a) Connect your Android or iOS device to your home Wi-Fi

network. Download the Google Home app. Sign in with

your Google account. If you do not have, create a new

one.

b) Follow the app instructions to complete setup.

www.jbl.com

English

CHROMECAST, AIRPLAY READY

(Android/iOS)

SETUP WIFI

Google Home

*Through the Airplay speaker setup

a) Connect your iOS device to your home Wi-Fi network.

b) On your iOS device, go to Settings > Wi-Fi. Under SET UP

NEW AIRPLAY SPEAKER…, select “ ”

and follow onscreen instructions to complete setup.

AIRPLAY READY

Settings Wi-Fi

Wi-Fi

JBL Bar 5.1_xxxx

XXX

SET UP NEW AIRPLAY SPEAKER…

(iOS)

SETUP WIFI

3. If necessary, use an Ethernet cable to connect the soundbar

to your home network.

• Make sure that you connect to the same network as you

did during the setup.

NOTES:

−During the Wi-Fi setup through the Google Home app, you can name

the soundbar and organize it by room.

−On your iOS device, add the soundbar to the Apple Home app and

manage it together with other AirPlay 2-compatible speakers.

−*On your iOS device, if the soundbar has been added to your home

Wi-Fi network through the Google Home app, skip the steps under

“Through Airplay speaker setup” and you can start Airplay streaming

from an Airplay-compatible app (See “Play through Airplay” in the

“PLAY” chapter).

5.4 Bluetooth connection

Through Bluetooth, connect the soundbar with your Bluetooth

device, such as a smartphone, tablet and laptop.

Settings Bluetooth

Bluetooth

DEVICES

JBL Bar 5.1_xxxx

Now Discoverable

Connected

< 10 m / 33 ft

BT PAIRING

Connect a Bluetooth device

1. Press to switch on (See “Power-on/Auto standby/Auto

wakeup” in the “PLAY” chapter).

2. To select Bluetooth source, press on the soundbar or on

the remote control.

→“”: Ready for BT pairing

3. On your Bluetooth device, enable Bluetooth and search for

“ ” within three minutes.

→Successful connection: The device name is displayed

if your device is named in English. A conrmation tone

is heard.

To reconnect the last paired device

Your Bluetooth device is retained as a paired device when the

soundbar goes to standby mode. Next time you switch to the

Bluetooth source, the soundbar reconnects the last paired

device automatically.

To connect to another Bluetooth device

1. In the Bluetooth source, press and hold on the soundbar or

on the remote control until “ ” is displayed.

→The previously paired device is cleared from the soundbar.

→The soundbar enters the Bluetooth pairing mode.

2. Follow the Step 3 under “Connect a Bluetooth device”.

• If the device has ever been paired with the soundbar, rst

unpair “ ” on the device.

NOTES:

−The Bluetooth connection will be lost if the distance between the

soundbar and Bluetooth device exceeds 33 ft (10 m).

−Electronic devices may cause radio interference. Devices that generate

electromagnetic waves must be kept away from the Soundbar, such

as microwaves and wireless LAN devices.

6. PLAY

6.1 Power-on/Auto standby/Auto wakeup

POWER

3HELLO

POWER

2 1

Switch on

1. Connect the soundbar and subwoofer to power by using the

supplied power cords.

→The screen on the soundbar shows “ ” and then, “

”.

2. On the soundbar, press to switch on.

→“” is displayed.

→The subwoofer is connected to the soundbar automatically.

Connected: turns solid white.

NOTES:

−Use the supplied power cords only.

−Before connecting to power, make sure that you have properly plugged

the power cords into the soundbar and subwoofer.

−Before switching on the soundbar, make sure that you have completed

all other connections (See “TV connection” and “Digital device

connection” in the “Connect” chapter).

Auto standby

If the soundbar is inactive for more than 10 minutes, it will switch

to standby mode automatically. “ ” is displayed. The

subwoofer also goes to standby, and turns solid amber.

Next time you switch on the soundbar, it returns to the last

selected source.

Auto wakeup

In standby mode, the soundbar will wake up automatically when

• the soundbar is connected to your TV through the HDMI

ARC connection and your TV is switched on;

Andere Handbücher für Bar 5.1 Surround

Inhaltsverzeichnis

Andere JBL Sprecher Handbücher

JBL

JBL Northbridge E30 Bedienungsanleitung

JBL

JBL Studio 235C Installations- und Betriebshandbuch

JBL

JBL Control 126W Bedienungsanleitung

JBL

JBL VRX932LA-1 Bedienungsanleitung

JBL

JBL Classic Series Bedienungsanleitung

JBL

JBL XTi 80 Bedienungsanleitung

JBL

JBL INSTALLATION P81BB Bedienungsanleitung

JBL

JBL GTO 1002D Gebrauchsanweisung

JBL

JBL LSR2325P Bedienungsanleitung

JBL

JBL MS6510 Bedienungsanleitung

JBL

JBL Control Control 47HC Bedienungsanleitung

JBL

JBL Lancer L55 Bedienungsanleitung

JBL

JBL L56 Bedienungsanleitung

JBL

JBL SRX715/F Bedienungsanleitung

JBL

JBL Harman PARTYBOX 110 Bedienungsanleitung

JBL

JBL MPro 200 Bedienungsanleitung

JBL

JBL AEC65 Bedienungsanleitung

JBL

JBL TLX271P Bedienungsanleitung

JBL

JBL Project K2 S9800 Bedienungsanleitung

JBL

JBL Intellivox ADC V90 Mark II Bedienungsanleitung

JBL

JBL Micro II Bedienungsanleitung

JBL

JBL LSR708i Handbuch

JBL

JBL Custom Shop CSC2295H Bedienungsanleitung

JBL

JBL L222 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung