jcb DD12Li Installationshandbuch
SO53 3LE
Customer Helpline 0845 600 5526
SAFETY AND OPERATING MANUAL
CORDLESS DRILL DRIVER
JCB-DD12Li
ORIGINAL INSTRUCTIONS
SO53 3LE
Customer Helpline 0845 600 5526
SO53 3LE
Customer Helpline 0845 600 5526
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all
safety warnings and all
instructions.
Failure to follow the
warnings and instructions may
result in electric shock, fire and/or
serious injury.
Save all warnings and instructions
for future reference.
The term “power tool” in the
warnings refers to your mains-
operated (corded) power tool or
battery-operated (cordless) power
tool.
1. Work area safety
a) Keep work area clean and well
lit.
Cluttered or dark areas invite
accidents.
b) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust.
Power tools create
sparks which may ignite the dust
or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to
lose control.
2. Electrical safety
a) Power tool plugs must match
the outlet. Never modify the plug
in any way. Do not use any adapter
plugs with earthed (grounded)
power tools.
Unmodified plugs
and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with
earthed or grounded surfaces,
such as pipes, radiators, ranges
and refrigerators.
There is an
increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools
to rain or wet conditions.
Water
entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use.
Use of
a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a
damp location is unavoidable, use
a residual current device (RCD)
protected supply.
Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.
A moment of inattention while
operating power tools may result
in serious personal injury.
b) Use personal protective
equipment. Always wear eye
SO53 3LE
Customer Helpline 0845 600 5526
SO53 3LE
Customer Helpline 0845 600 5526
protection.
Protective equipment
such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off-
position before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising
power tools that have the switch
on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on.
A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of
the power tool in unexpected
situations.
f) Dress properly. Do not wear
loose clothing or jewellery. Keep
your hair, clothing and gloves
away from moving parts.
Loose
clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a) Do not force the power tool.
Use the correct power tool for
your application.
The correct
power tool will do the job better
and safer at the rate for which it
was designed.
b) Do not use the power tool if
the switch does not turn it on and
off.
Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from
the power source and/or the
battery pack from the power tool
before making any adjustments,
changing accessories, or storing
power tools.
Such preventive
safety measures reduce the
risk of starting the power tool
accidentally.
d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool.
Power
tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use.
Many
accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and
clean.
Properly maintained cutting
SO53 3LE
Customer Helpline 0845 600 5526
tools with sharp cutting edges are
less likely to bind and are easier
to control.
g) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use
of the power tool for operations
different from those intended
could result in a hazardous
situation.
5. Battery tool use and care
a) Recharge only with the charger
specified by the manufacturer.
A
charger that is suitable for one
type of battery pack may create
a risk of fire when used with
another battery pack.
b) Use power tools only with
specifically designated battery
packs.
Use of any other battery
packs may create a risk of injury
and fire.
c) When battery pack is not in
use, keep it away from other metal
objects, like paper clips, coins,
keys, nails, screws or other small
metal objects, that can make a
connection from one terminal
to another.
Shorting the battery
terminals together may cause
burns or a fire.
d) Under abusive conditions,
liquid may be ejected from the
battery; avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery
may cause irritation or burns.
6. Service
a) Have your power tool serviced
by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained.
b)
If the replacement of the supply
cord is necessary, this has to be
done by the manufacturer or its
agent in order to avoid a safety
hazard.
SO53 3LE
Customer Helpline 0845 600 5526
SO53 3LE
Customer Helpline 0845 600 5526
ADDITIONAL SAFETY RULES FOR YOUR CORDLESS DRILL DRIVER
1. Remove the battery pack
from the drill before carrying out
adjustments.
2. Do not expose to rain or water.
3. Do not store the battery pack
in temperature over 40oC.
4. Always charge the battery
pack between temperature 0oC to
30oC. Ideal charging temperature
is 18oC to 24oC.
5. Only use the charger and
battery pack provided - do not
use any other charger or battery
pack not intended for use with
this model.
6. Avoid short circuit of the
battery pack connections (screws
& nails).
7. Do not incinerate or burn the
battery pack, it may explode.
8. Do not charge a damaged
battery pack.
9. Replace any damaged supply
cords on your charger.
10.Always disconnect the charger
power supply before breaking the
connections to the battery pack.
11.Battery pack and charger will
be warm during charging this is
normal.
12.When not in use, remove a
charged battery pack from the
charger.
13.Always remove the battery
pack from the charger
immediately after re-charging is
completed.
14.Your drill and battery pack will
be warm when working, this is
normal.
15.Do not dispose of batteries
in fire, or with household waste.
Return exhausted batteries to
your local collection or recycling
point.
16.Always check walls, floors and
ceilings for hidden power cables
and pipes.
17.Wear ear protection with
cordless drill. Exposure to noise
can cause hearing loss.
18.Accessories and metal parts
can become very hot.
19.Hold power tool by insulated
gripping surfaces, when
performing an operation where
the cutting accessory may
contact hidden wiring. Cutting
accessory contacting a "live" wire
may make exposed metal parts of
the power tool "live" and result in
operator injury.
WARNING: If a small
amount of electrolyte
should leak from the battery pack
under extremes of temperature
or after heavy use, then wash
off immediately from your skin
and hands using clean water. For
eye contact, rinse thoroughly with
clean water and seek medical
treatment immediately.
SO53 3LE
Customer Helpline 0845 600 5526
SYMBOLS
To reduce the risk of injury, user must read
instruction manual
Warning
Indoor use only
Wear ear protection
Wear eye protection
Wear dust mask
Do not expose to rain or water
Do not burn
Always charge the battery pack between
temperatures 0oC to 30oC
Do not dispose of batteries. Return
exhausted batteries to your local collection
or recycling point.
SO53 3LE
Customer Helpline 0845 600 5526
SO53 3LE
Customer Helpline 0845 600 5526
1. KEYLESS CHUCK
2. TORQUE ADJUSTMENT RING
3. TWO-SPEED GEAR CONTROL
4. FORWARD/REVERSE ROTATION CONTROL
5. SOFT GRIP HANDLE
6. BATTERY PACK RELEASE BUTTON
7. BATTERY PACK
8. ON/OFF SWITCH
9. LED LIGHT
COMPONENT LIST
1 2 3
4
5
6
7
8
9
SO53 3LE
Customer Helpline 0845 600 5526
TECHNICAL DATA
Voltage 12V
No load speed 0-350/ 0-1300/min
Number of clutch positions 15+1
Max torque 14/24 N.m(soft/hard)
Chuck capacity 10mm
Max. drilling
capacity
Steel 10mm
Wood 20mm
Machine weight 1.0Kg
NOISE INFORMATION
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined according to EN 60745:
Drilling into metal
Vibration emission value ah=1.24m/s²
Uncertainty K =1.5m/s²
A weighted sound pressure LpA: 73dB (A)
A weighted sound power LwA: 84dB (A)
KpA & KwA=3.0dB (A)
Wear ear protection when sound pressure is over: 80dB (A)
WARNING:
The vibration emission value during actual use of the power tool
can differ from the declared value depending on the ways in which the tool is
used dependant on the following examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
To use the correct accessory for the tool and ensure it is sharp and in good condition.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
SO53 3LE
Customer Helpline 0845 600 5526
SO53 3LE
Customer Helpline 0845 600 5526
WARNING:
To be accurate, an estimation of exposure level in the actual
conditions of use should also take account of all parts of the operating cycle
such as the times when the tool is switched off and when it is running idle but not
actually doing the job. This may significantly reduce the exposure level over the total
working period.
Help to minimize your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 10oC or less.
Plan your work schedule to spread any high vibration tool use across a number of
days.
ACCESSORIES:
We recommend that you purchase your accessories from the same store that
sold you the tool. Use good quality accessories marked with a well-known brand
name. Choose the type according to the work you intend to undertake. Refer to the
accessory packaging for further details. Store personnel can assist you and offer
advice.
1.3 Ah lithium battery pack (JCB-BAT12Li) 1
Double end bit 1
3 - 5 h charger (JCB-SCH12Li)---Fit for single drill driver 1
1 h charger (JCB-FCH12Li)---Fit for twinpack (impact driver and drill driver) 1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
