JEFF ROWLAND 501 Bedienungsanleitung

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

TABLE OF CONTENTS

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

Introduction 2

Product Features 3

Package Contents 4

Initial Inspection 5

Maintenance & Cleaning 6-7

Protection Systems 7

Installation, Use & Care 8-9

Signal & Power Connections 10-12

Specications 13

Dimensions 14

Optional Adjustments 15

PO BOX 7231, COLORADO SPRINGS, COLORADO 80933 USA E-mAIL: jRDG@jEffROwLAND.COm www.jEffROwLAND.COm TELEPHONE (719) 473-1181

If you have any additional questions

regarding the installation or operation

of the Model 501 Mono Ampliﬁer, please

contact your authorized Jeff Rowland

Design Group dealer or check the Jeff

Rowland Design Group web site at

www.jeffrowland.com.

Enjoy the music!

Jeff Rowland

President,

Jeff Rowland Design Group

to gain the maximum performance and

ease of use for which this ampliﬁer was

designed. Please note that your Model 501

Mono Ampliﬁer serial number begins with

the letters “MD”. This serial number is

located on the rear panel of the chassis.

Please include this number with any corre-

spondence regarding your Model 501

Mono Ampliﬁer. It has been my joy to

create an audio component of enduring

value that reﬂects the highest ideals of

musical and artistic expression. It is my

hope that these qualities will enrich your

experience and pride of ownership.

Welcome to the Jeff Rowland Design

Group “family” and congratulations on your

purchase of what is unquestionably one

of the world’s ﬁnest ampliﬁers. With its

combination of features such as precision

electronic circuitry, exceptional

efﬁciency,

and accurately machined chassis compo-

nents throughout, your

Model 501 Mono

Ampliﬁer will offer you many years of musi-

cally satisfying enjoyment.

Please take a few minutes to read the

remainder of this Owner’s Manual before

proceeding with the installation of the

ampliﬁer. A thorough understanding of

the operational features will allow you

INTRODUCTION

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

•

XLR input connector for balanced

system congurations. Same gain

and input impedance characteristics

are ensured whether XLR or RCA

adapted inputs are used.

• Transformer coupled input provides

universal compatibility with other

components and eliminates ground

loop noise and EMI.

• High efciency ICEpower® power

conversion technology generates

high output power with very little heat,

promotes long component life and

permits a relatively small physical size.

• Multistage AC line ltering in power

supply reduces AC line noise pollution

throughout amplier signal circuitry.

• CE approved speaker output terminals

require no tools for secure, low resis-

tance connections.

• Fully-balanced topology

implemented

in both input and output circuitry.

• Proprietary switch-mode power

supply technology ensures

consistent performance under all

operating and AC line conditions.

• Low power consumption permits

constant power-up operation to

eliminate warm-up time.

• Selectable overall gain of 26 or 32 dB.

• Ultra-low resonance, structurally

rigid chassis,

precision-machined

from a solid block of aircraft grade

6061-T6 aluminum.

• Remote ON/OFF input jack allows

amplier standby operation from

remote source for inclusion into

home

theater (A/V) systems.

PRODUCT FEATURES

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

PO BOX 7231, COLORADO SPRINGS, COLORADO 80933 USA E-mAIL: jRDG@jEffROwLAND.COm www.jEffROwLAND.COm TELEPHONE (719) 473-1181

Ensure that all of the auxiliary components listed below are enclosed within the shipping carton

and accessory box. Refer to the illustrations and verify that the proper components are included.

PACKAGE CONTENTS

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

OWNER’S MANUALMODEL 501 MONO AMPLIFIER AC POWER CABLE

WARRANTY REGISTRATION

WARRANTY CARD

Inspect the shipping container for damage. If any portion of the shipping container, packing material,

ampliﬁer, or accessories are damaged or missing, notify your dealer and the shipper (if a claim is to

be made) immediately.

NOTE:

Many shippers require notication and inspection within 24 hours of delivery to determine the nature of damages incurred.

Your Model 501 Mono Ampliﬁer has undergone extensive performance evaluations, listening tests,

quality control inspections, and a minimum 72 hour burn-in period prior to shipment and should

therefore be in perfect operating condition upon delivery. If the ampliﬁer does not operate correctly,

please notify your dealer immediately.

We strongly suggest that you save all of the packing materials. If the ampliﬁer is returned to your

dealer or JRDG, the original packing materials must be used for shipment to avoid possible damage.

Neither JRDG nor the shipper can be held responsible for damages incurred during transit if the

original factory packing is not used. All factory returns require that JRDG issue a Return Authorization

(RA) number prior to shipment.

INITIAL INSPECTION

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

PO BOX 7231, COLORADO SPRINGS, COLORADO 80933 USA E-mAIL: jRDG@jEffROwLAND.COm www.jEffROwLAND.COm TELEPHONE (719) 473-1181

All JRDG products are designed to provide

a lifetime of enjoyment

and listening pleasure. The Model 501 Mono

Ampliﬁer is uniquely

constructed from a solid block of precision-machined aluminum.

It’s chassis is sealed to prevent dust from

entering the interior of

the chassis and thus should never need interior cleaning during the

lifetime of the product. All internal circuitry is maintenance-free such

that no adjustments of any kind are necessary over the lifetime of

the product. If the ampliﬁer is ever in need of service, updating, or

upgrading, it should only be returned to an authorized repair facility

or technician for servicing.

The front panel of the unit is precision-machined in a unique process

that incorporates a diamond tipped cutting tool. This process was reﬁned

over many years to produce an attractive and unique appearance.

Because the surface is not ﬁnished in the typical fashion of most

audio and video equipment, there are a few rules that must be kept

in mind when cleaning the equipment.

• Please allow the front panel, which is coated with an automotive-grade polyure-

thane nish, to cure for 6 months before attempting to clean it.

This will prevent

small scratches from marring the surface before the surface coating has had a

chance to harden completely.

• The front panel of the unit should never be cleaned with anything other than a very

soft cotton cloth and plain water or ne oil-based furniture polish. Because of the

ne nish of the front panel, use of any other cleaning agent may permanently

scratch the nish.

• The top cover, sides and bottom are protected by a durable black anodized nish

and can be cleaned with a soft cotton cloth (such as an optical lens cleaning cloth

or ne furniture polishing rag) dampened with plain water. Water should be applied

directly to the cloth and not the chassis. A very mild plastic or glass cleaner that

does not contain ammonia may also be used. If a mark has been left on the

chassis,

do not use any type of abrasive or chemical cleaner to remove the mark.

Maintenance & cleaning

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

Protection SyStemS

The Model 501 Mono Ampliﬁer is equipped with internal fuses for

protection against excessive AC current draw; however, since no

protection circuitry or system can completely protect a product from

every electrical hazard, certain precautions should be observed.

In the event of severe voltage hazards such as lightning or when the

ampliﬁer

will not be used for extended periods of time, the ampliﬁer

should be unplugged from the AC mains to avoid potential damage

to the internal circuitry. All other audio/video system components

should also be disconnected from AC mains power as hazardous

voltages can easily travel throughout an interconnected system.

If you have any questions about the care or cleaning of your Model

501 Mono Ampliﬁer, please contact your dealer or the JRDG factory

before attempting to clean the chassis. The use of a cleanser or

abrasive to clean the chassis that has not been approved by the

factory will almost certainly damage the ﬁnish and will not be

covered under warranty.

NOTE: Cleaner/polish should be applied directly to the cloth and not the chassis.

PO BOX 7231, COLORADO SPRINGS, COLORADO 80933 USA E-mAIL: jRDG@jEffROwLAND.COm www.jEffROwLAND.COm TELEPHONE (719) 473-1181

InstallatIon, Use & care

OWNER’S MANUAL MODEL 501 MONO AMPLIFIER

Locate the ampliﬁer as close as possible to its ﬁnal installation point. Allow access to the rear

panel for making connections. Due to it’s design, the Model 501 Mono Ampliﬁer is energy

efﬁcient, eliminating the need for heatsinks or forced-air cooling. As a result, the Model 501

Mono Ampliﬁer can be housed in a cabinet or custom enclosure with no fear of overheating.

The efﬁcient and compact design of the Model 501 allows it to be

installed in any number of

music, ﬁlm and surround sound systems. For connection instructions for use in a typical two-

channel stereo system, please see page 11 of this manual.

The main chassis of the Model 501 is precision-machined out of a solid block of aluminum to

create as rigid an enclosure as possible, impervious to lateral and torsional forces. The ampliﬁer

is particularly non-resonant; however, various damping and resonance control accessories

may be used to yield greater audio performance in some audio systems.

RISK OF ELECTRICAL SHOCK!

WARNING

: Do not attempt to access the interior of the MODEL 501 MONO AMPLIFIER by removing the bottom

cover. Doing so will void your warranty and could expose you to dangerous, potentially lethal electrical voltages.

The JRDG Model 501 Mono

Ampliﬁer has been designed to

operate at the highest level of

efﬁciency and performance in

any normal operating situation;

however, there are a few impor-

tant use and care principles

that must be kept in mind when

operating the ampliﬁer.

•

Do not expose the amplier to

rain, moisture, or excessively

damp conditions.

• Make sure that the voltage on the

backside of the panel matches the

mains voltage in your area.

•

The Model 501 Mono Amplier

must not be modied in any way,

other than according to ofcial

service bulletins from JRDG.

Otherwise, the factory warranty

will be immediately voided.

•

Be sure the amplier power switch

is turned off or AC power cable

is removed

before connecting or

disconnecting any loudspeaker or

interconnect cables.

• When operating the Model 501,

properly grounded AC receptacle

should be used. A potential shock

hazard may result if the supplied

3-wire, grounded AC cable ground

terminal is defeated or lifted or

the unit is connected to a 2-wire

ungrounded AC outlet.

• The Model 501 is designed to per-

form

optimally with no adjustments

maintenance for the lifetime of the

product. Do not attempt to open the

bottom cover of the amplier and

refer all service issues to qualied

personnel. The voltages inside the

Model 501 can be hazardous.

• Because of the energy efciency

of the Model 501, there is no need

to turn the unit off when not in use

except in the event of severe voltage

hazards as mentioned previously.

Andere Handbücher für 501

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JEFF ROWLAND Verstärker Handbücher

JEFF ROWLAND

JEFF ROWLAND 501 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 8T Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 825 Kurzanleitung

JEFF ROWLAND

JEFF ROWLAND 112 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 10 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND Cadence Phono Stage Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 7 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 102 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 312 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 302 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 302 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND CAPRI S2 Kurzanleitung

JEFF ROWLAND

JEFF ROWLAND 625 Kurzanleitung

JEFF ROWLAND

JEFF ROWLAND Concentra Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND Model 2 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 525 Kurzanleitung

JEFF ROWLAND

JEFF ROWLAND CRITERION Kurzanleitung

JEFF ROWLAND

JEFF ROWLAND 301 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 6 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND CONCERTO Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND Coherence Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND 925 Kurzanleitung

JEFF ROWLAND

JEFF ROWLAND CONTINUUM 250 Bedienungsanleitung

JEFF ROWLAND

JEFF ROWLAND Capri Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung