Jegs JEGS 30 Bedienungsanleitung
[ 1 ]
Table of Contents
1. Transmitter Feature Diagram........................................................... 2
2. Installing Batteries ........................................................................... 3
3. Basic Operation ................................................................................. 3
4. Binding Transmitter ......................................................................... 4
5. Lock/Unlock Key Button ................................................................... 4
6. Steering Adjustment ......................................................................... 4
• Reversing Servo...................................................................................... 4
• Steering End Point Adjustment ........................................................ 5
• Steering Digital Trimming Adjustment .......................................... 5
• Dual Rate Steering Adjustment........................................................ 6
7. Throttle Adjustment .......................................................................... 6
• Throttle Reverse Setting..................................................................... 6
• Throttle End Point Adjustment......................................................... 7
• Throttle Digital Trimming Adjustment........................................... 8
8. Auxiliary Channel 3 Adjustment...................................................... 8
• Reverse Setting ...................................................................................... 8
• On/Off CH3 Switch Setting................................................................ 9
9. Factory Reset ..................................................................................... 9
• Factory Default Setting ....................................................................... 9
10. FUNC................................................................................................. 9
• FUNC Mode
11. Receiver..........................................................................................10
• Receiver Binding ..................................................................................10
• Fail-Safe Adjustment..........................................................................10
12. Power Alarm ..................................................................................10
• No Activity Alarm.................................................................................10
• Low Battery Voltage Alarm...............................................................10
13. Certication ...................................................................................11
14. Specications ................................................................................12
[ 2 ]
1 — Transmitter Feature Diagram
2
[ 3 ]
2 — Installing Batteries
1. Remove the battery cover from the transmitter.
2. Insert 4 AA alkaline dry cell batteries
according to their polarity.
3. Replace the battery cover.
3 — Basic Operation
[ 4 ]
4 — Binding Transmitter
1. Each transmitter is assigned a random unique ID number. In order to
begin using the transmitter system, you will have to bind the receiver
to the transmitter.
2. Follow the receiver binding instructions on page 10.
5 — Lock/Unlock Key Button
6 — Steering Adjustment
Lock Key Button
1. Push the D/R switch to the Right.
2. While holding the D/R switch
to the right, turn the transmitter
power switch to ON.
3. Two short “beep” sounds indicate
conrmation and the LED light
ashes.
4. All button functions are
now locked.
Unlock Key button
1. Push the D/R switch to the Left.
2. While holding the D/R to the left,
turn the transmitter power switch
ON.
3. Two short “beep” sounds indicate
conrmation.
4. All button functions are
now unlocked.
Reversing Servo
1. Press and hold steering wheel
(ST) R/+ key button.
2. While pressing ST R/+ key
button, turn on the transmitter
power switch.
3. Two short “beep” sounds
indicate conrmation.
4. The steering has now
been reversed.
[ ST = Steering Wheel TH = Throttle Trigger ]
[ 5 ]
Left Steering End Point Adjustment
1. Turn the steering wheel (ST) fully to the left.
2. Once the value reaches the limit,
a long steady “beep” will sound.
• Decrease value: Turn the steering
wheel fully to left and press
ST L-key button
• Increase value: Turn the steering
wheel fully to the left and press
ST R+ key button
3. Use this to decrease or increase left steering angle adjustment.
Steering Digital Trimming Adjustment
1. Once the value reaches the limit,
a long steady “beep” will sound.
2. Two short “beep” sounds indicate the
steering is at the neutral position.
a. Decrease: Press ST L/- key button
b. Increase: Press ST R/+ key button
3. When the vehicle is not moving, this
function allows you to adjust the
steering to the neutral position.
Right Steering End Point Adjustment
1. Turn the steering wheel (ST) fully to the right
2. Once the value reaches the limit,
a long steady “beep” will sound.
• Decrease value: Turn the steering
wheel fully to the right then press
ST L- key button
• Increase value: Turn the steering
wheel fully to the right then press
ST R+ key button
3. Use this to decrease or increase right steering angle adjustment.
Steering End Point Adjustment
[ ST = Steering Wheel TH = Throttle Trigger ]
[ 6 ]
Dual Rate Steering Adjustment
• Decrease: Push the D/R button
to the left
• Increase: Push the D/R button
to the right
1. Once the value reaches the limit,
a long steady "beep" will sound.
2. Dual-rate Steering allows on-the
y travel adjustment to both sides
(left and right) of the steering servo.
7 — Throttle Adjustment
Throttle Reverse Setting
1. Press and hold ST L/- key button.
2. While holding ST L/- key button turn the transmitter power switch to ON.
3. Two short “beep” sounds indicate conrmation.
4. The throttle trigger has now been reversed.
[ ST = Steering Wheel TH = Throttle Trigger ]
[ 7 ]
Throttle (Accelerate)
1. Pull and hold the throttle trigger
(TH) fully to the Forward-side.
2. Once the value reaches the limit,
a long steady “beep” will sound.
• Decrease: While holding the
throttle trigger, press
TH Rev/- button
• Increase: While holding the
throttle trigger, press
TH Fwd/+ button
3. Use the TH Rev/- or TH Fwd/+
buttons to adjust the throttle
trigger to desired throw.
4. This can also be performed when the
receiver power is off.
Throttle End Point Adjustment
Brake (Decelerate)
1. Push the throttle trigger (TH) fully
to the brake-side
2. Once the value reaches the limit,
a long steady “beep” will sound.
• Decrease: While holding the brake
trigger, press TH Rev/- button
• Increase: While holding the brake
trigger, press TH Fwd/+ button
3. Use the TH Rev/- or TH Fwd/+
buttons to adjust the brake to
desired throw.
4. This can also be performed when
the receiver power is off.
[ ST = Steering Wheel TH = Throttle Trigger ]
[ 8 ]
When the vehicle is not moving, this
function allows you to adjust the
throttle to the neutral position.
1. Once the value reaches the limit,
a long steady “beep” will sound.
2. Two short “beep” sounds indicate
conrmation.
• Decrease: Press TH Rev/-
button
• Increase: Press TH Fwd/+
button
3. If the value is lower than the
setting limit of ESC, some
functions may be invalid.
8. Auxiliary Channel 3 Adjustment
Reverse Setting
1. Press and hold CH3 key button
while turning the power switch on.
2. Listen for Two short “beep” sounds
for conrmation.
3. The CH3 Function has now been
reversed.
Throttle Digital Trimming Adjustment
[ ST = Steering Wheel TH = Throttle Trigger ]
[ 9 ]
On/Off CH3 Switch Setting
This function allow you to turn On/Off the
CH3 key-button.
1. Two quick presses of the CH3 key button.
• Turn-On: Two short beep sounds
• Turn-Off: One short beep sound
9 — Factory Reset
Factory Default Setting
1. Press and hold the TH Fwd/+ or TH Rev/- key button.
2. While holding the Fwd/+ or Rev/- key button turn
the transmitter switch to ON.
3. Two short beep for conrmation.
4. Your transmitter has now
reset to the factory
setting.
10 — FUNC
FUNC Mode
FUNC Mode locks all the key buttons and
throttle except the steering wheel.
1. To enter the FUNC mode, Turn the
transmitter power switch to ON, press
and hold the FUNC key button, two short
“beep” sounds for conrmation.
2. To leave the FUNC mode, press the FUNC
key button once, two short “beeps” will
sound for conrmation.
[ ST = Steering Wheel TH = Throttle Trigger ]
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
