Jenn-Air JCD2290HE Bedienungsanleitung

TABLE OF CONTENTS

Form No. A/05/06 Part No. 12842132 www.jennair.com Printed in USA

Important Safety Instructions ........................................1-2

Installation.............................................................................3-8

Temperature Controls.....................................................9-11

Fresh Food Features.....................................................12-14

Freezer Features ...................................................................15

Ice and Water..................................................................16-18

Water Filter.......................................................................19-21

Food Storage Tips..........................................................22-24

Care and Cleaning ........................................................25-28

Operating Sounds ................................................................29

Troubleshooting..............................................................30-33

Warranty and Service..........................................................35

Guide d’utilisateur et d’entretien....................................36

Guía de uso y cuidado .......................................................74

JENN-AIR SIDE-BY-SIDE REFRIGERATOR

USE & CARE

GUIDE

IMPORTANT SAFETY INSTRUCTIONS

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

WARNING

DANGER – Immediate hazards which WILL result

in severe personal injury or death.

DANGER

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury or property damage.

CAUTION

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounded plug for your protection against possible

electrical shock hazards. It must be plugged into a

properly grounded wall receptacle. Where a standard

two-prong wall receptacle is encountered, it is the

personal responsibility and obligation of the customer

to have it replaced with a properly grounded three-

prong wall receptacle. Do not, under any

circumstances, cut or remove the third (ground)

prong from the power cord. Do not use an adapter

plug.

Power supply cord with

three-prong grounded plug

Properly

grounded type

wall receptacle

To reduce risk of injury or death, follow basic

precautions, including the following:

Important: Child entrapment and suffocation are

not problems of the past. Junked or abandoned

refrigerators are still dangerous – even if they sit out

for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

•Take off the doors.

• Leave the shelves in place so

children may not easily climb

inside.

• Cut off power cord plug.

DANGER

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this Use and

Care Guide for future reference; it provides the

proper use and maintenance information.

Keep sales receipt and/or canceled check as proof

of purchase.

Call: 1-800-JENNAIR (1-800-536-6247)

USA and Canada

(Mon.-Fri., 8am-8pm Eastern Time)

Internet: http://www.jennair.com

Have complete model and serial number

identification of your refrigerator. This is located on a

data plate inside the fresh food compartment, on the

upper right side. Record these numbers below for

easy access.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

To reduce risk of fire, electric shock, serious

injury or death when using your refrigerator,

follow basic precautions, including the following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure this appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

115 volt, 15 amp., 60 cycle line.

8. Do not modify plug on power cord. If plug does

not fit wall receptacle, have proper receptacle

installed by a qualified electrician.

9. Do not use a two-prong adapter, extension cord

or power strip.

10. Do not remove warning tag from power cord.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any part of refrigerator

unless specifically recommended in Use and Care

Guide or published user-repair instructions.

Do not attempt service if instructions are not

understood or if they are beyond personal skill

level.

13. Always disconnect refrigerator from electrical

supply before attempting any service. Disconnect

power cord by grasping the plug, not the cord.

14. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and grounding must comply with local

codes and be made by licensed personnel when

required.

15. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

16. Have worn power cords and/or loose plugs

replaced by a qualified service technician.

17. Always read and follow manufacturer’s storage

and ideal environment instructions for items being

stored in refrigerator.

18. Your refrigerator should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any

part of the refrigerator.

20. Clean up spills or water leakage associated with

water installation.

WARNING

INSTALLATION

Location

•Do not install refrigerator near oven, radiator or

other heat source. If not possible, shield refrigerator

with cabinet material.

•Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

•Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, allow 1⁄2” space at top

and 1⁄2” space behind machine compartment cover

(located in the rear) for proper air circulation. If the

refrigerator is placed with the door hinge side against

a wall, you may want to allow additional space so the

door can be opened wider.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling, page 5.

Important: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

•NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging

refrigerator in immediately may cause damage to

internal parts.

Glass Panel Doors (select models)

To avoid possible injury, product or property

damage, observe the following:

• When working directly on the doors, protect the

door corners and sides by placing doors on a

nonabrasive surface protected by towels or rugs.

• Protect the glass panel sides when securing the

unit to a dolly. Do not over-tighten!

Over-tightening the restraints may shatter the

glass, which could cause personal injury.

•Do not carry or transport removed doors by the

handles.

• Fully tighten handle set screws when installing the

door handles.

CAUTION

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

To Disconnect the Water Line:

• Push in white collar (A) and hold.

• Pull the door-side tube from the connector (B).

To Reconnect the Water Line:

• Firmly push tube 5⁄8” into the connector. Use

lines on the tube as a guide for full insertion.

• If tube end is

damaged, cut off 5⁄8”

before reconnecting.

• If leaking occurs,

reconnect the line.

3. Close doors.

4. Remove top hinge covers by

removing Phillips screws.

5. Unscrew 5⁄16” hex head screws from

top hinges.

6. For ice and water dispensing

models only: Detach main wire

connector harness.

•Do not remove screw

connecting green ground wire.

• To detach main wire harness,

use a flat blade tool or finger-

nail to press junction point

between two connectors to

release.

7. Remove top hinges along with doors.

INSTALLATION

To avoid severe personal injury or death,

observe the following:

• Disconnect power to refrigerator before removing

doors. Connect power only after replacing doors.

• Green ground wire must be attached to top hinge

while performing door removal and replacement.

• Tape decorative panels (select models) securely

into place before removing door handles.

WARNING

To avoid property damage, observe the following:

• Protect vinyl or other flooring with cardboard,

rugs or other protective material, prior to moving

refrigerator.

•Do not adjust refrigerator to be any shorter than

681⁄2” tall (minus hinge and cap). Doing so may

damage underside components.

CAUTION

Door and Hinge Removal

Some installations require door removal to get

refrigerator to final location.

Materials Needed:

• Phillips screwdriver

•5⁄10” heax head screws

1. Unplug power cord from power source.

2. Remove toe grille (see page 5).

• Open both doors 180°, or as wide as possible.

8. Remove bottom hinges with a 3⁄8” hex head driver.

Replacing the Doors

•To replace the doors, follow the steps in Door and

Hinge Removal in reverse order.

Important: If water line tube end is damaged, cut off

5⁄8” before reconnecting.

Note: For refrigerators in operation, shut off water

before removing water line from the door.

INSTALLATION

Leveling

To protect personal property and refrigerator

from damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

•Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be level.

Notes:

• Complete any required door reversal, panel

installation and/or a water supply connection

before leveling.

• Some models only have adjustment screws (A).

3. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

4. Using the carpenter’s level, make sure front of

refrigerator is 1⁄4” (6 mm) or 1⁄2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

Materials Needed

•3⁄8” hex head driver

• Carpenter’s level

1. Remove toe grille.

• Grasp firmly and pull

outward to unclip.

2. Using hex head driver, turn front adjustment

screws (A) clockwise to raise and counterclockwise

to lower the front of the refrigerator.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

• Determine which

door needs to be

raised.

• Turn front roller

adjustment screw

(A) clockwise to

raise front corner of

door.

• If one refrigerator door has reached the limit of

its adjustment range and doors are still not level,

raise or lower the opposite door by turning roller

adjustment screw clockwise or counterclockwise.

• Check with level to verify 1⁄4” tilt to the back for

proper door closure.

• If refrigerator is aligned and stable, replace toe

grille and hinge covers.

5. If required, correct rocking of refrigerator by

turning rear adjustment screw clockwise to raise

rocking corner. If doors are uneven, do the

following:

INSTALLATION

Connecting the Water Supply

(select models)

To avoid property damage or possible injury,

follow basic precautions, including the

following:

•Consult a plumber to connect 1⁄4” O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

• Confirm water pressure to water valve is between

35 and 100 pounds per square inch, 20 pounds

per square inch without filter.

•Do not use a self-piercing, or 3⁄16” saddle valve.

Both reduce water flow can become clogged over

time, and may cause leaks if repair is attempted.

• Wait two to three hours before placing refrigerator

into final position to check and correct any water

leaks. Recheck for leaks after 24 hours.

• Verify the copper tubing under the sleeve is

smooth and free from defects. Do not reuse an

old sleeve.

CAUTION

To reduce risk of injury or death, follow basic

precautions, including the following:

• Read all instructions before installing ice maker.

•Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

• Observe all local codes and ordinances.

•Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

• Disconnect power to refrigerator before installing

ice maker.

• Water damage due to an improper water

connection may cause mold/mildew growth. Clean

up spills or leakage immediately.

WARNING

Materials Needed

•1⁄4” outer diameter flexible copper tubing

• Shut-off valve (requires a 1⁄4” hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench (2)

•1⁄4” hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with

copper tubing (minimum 2’

diameter). Avoid kinks in the

copper tubing when bending

the service loop. Do not use

plastic tubing.

2. Remove plastic cap from water valve

inlet port.

2’ diameter

minimum

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the Use and Care

packet.

5. Slide brass nut over sleeve and

screw nut into inlet port.

Place adjustable wrench on nut

(1) attached to plastic waterline

and maintain position.

Using second adjustable wrench,

turn the lower nut (2)

counterclockwise and fully

tighten while holding the upper

nut in place.

Important: Do not over-tighten. Cross threading

may occur.

4. Place end of copper tubing into

water valve inlet port. Shape

tubing slightly - Do not kink – so

that tubing feeds straight into inlet

port.

Cont.

2. Align notches on back of handle

with retaining clips on doors.

Insert clips into notches and

slide handle down until it

contacts bottom trim.

3. Replace top door trim and Phillips

screws.

4. Repeat instructions 1-3 to install

other handle.

To avoid possible injury and damage to property,

tape decorative panels (select models) securely into

place before removing door handles.

WARNING

Door Clip

Handle Extensions (select models)

To Install:

• Align and clip handle extension into position on the

handle. Press the extension over the door retainers.

To Remove:

• Slide the extension down and unclip from door

retainer.

Full-Length Aluminum Handles

Materials Needed:

•Phillips screwdriver

To Install:

1. Release top door trim (select models)

by removing Phillips screws from top

of fresh food door and retain screws

for later use.

Handle Installation

If not installed, the handle is located in the interior or

attached to the back of your refrigerator. Remove and

discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model.

Plastic Handle

To Install:

1. The handles are to be oriented

as shown.

2. Align door handle clip with the

door studs.

3. Ensure the large hole in

the mounting clip is

positioned down on both

ends of the handle.

4. Rotate the handle so that the

handle is flat against the door.

INSTALLATION

5. Grasp the handle firmly and slide

down.

To Remove:

1. Grasp the lower part of the handle firmly,

slide up, lift and remove from the

surface.

6. Pull on tubing to confirm connection is secure.

Connect tubing to frame with

water tubing clamp (C) and

turn on water supply. Check

for leaks and correct if

necessary. Continue to

observe the water supply

connection for two to three

hours prior to moving the

refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

Door

Stud

INSTALLATION

To Remove:

1. Release top door trim (select models)

by removing Phillips screws from top

of fresh food door and retain screws

for later use.

2. Grasp handle firmly with both

hands. Slide handle upward

approximately 3⁄4” to release.

3. Repeat instructions 1-2 to

remove other handle.

To Reinstall:

1. Repeat in reverse order.

Euro Handles

This handle style is installed at the factory.

Materials Needed:

•3⁄32” Allen wrench

To Remove:

• Remove set screw from

handle mounting post

using 3⁄32” Allen wrench.

• Repeat the procedure on

all posts to remove the

handle.

To Replace:

• Align handle with the mounting posts.

•Fully tighten all set screws to secure handle

in place.

To Remove:

• Loosen set screws in handle using 3⁄32” Allen

wrench.

• Repeat the procedure on all screws.

To Replace:

• Align handle with the mounting posts.

• Apply upward pressure to the handle and hold.

• Fully tighten all set screws to secure handle in

place.

Metal Handle

Materials Needed:

•3⁄32” Allen wrench

• Gloves to protect hands

Note: Metal handles can scratch doors.

TEMPERATURE CONTROLS

Touch Temperature Controls

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

• Pressing the or pads adjusts the controls to

the desired setting.

• Set the Freezer control on 4.

• Set the Refrigerator control on 4.

• Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

• 24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 22

for instructions on checking compartment

temperature.

• Except when starting the refrigerator, do not change

either control more than one number at a time.

• Allow 24 hours for temperatures to stabilize.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the Refrigerator control

to next higher number by

pressing the pad.

Set the Refrigerator control

to next lower number by

pressing the pad.

Set the Freezer control to

next higher number by

pressing the pad.

Set the Freezer control to

next lower number by

pressing the pad.

Press the Freezer or

Refrigerator pad until

a dash “–” appears in the

display.

Inhaltsverzeichnis

Sprachen:

Andere Jenn-Air Kühlschrank Handbücher

Jenn-Air

Jenn-Air W10231365B Bedienungsanleitung

Jenn-Air

Jenn-Air JS48SEDUDB01 Bedienungsanleitung

Jenn-Air

Jenn-Air JB36NXFXLW Bedienungsanleitung

Jenn-Air

Jenn-Air JFI2089AEP Bedienungsanleitung

Jenn-Air

Jenn-Air JBL2088HES Bedienungsanleitung

Jenn-Air

Jenn-Air jb36ssfxra Bedienungsanleitung

Jenn-Air

Jenn-Air JUGFR242HM00 Bedienungsanleitung

Jenn-Air

Jenn-Air JBL2088HES13 Bedienungsanleitung

Jenn-Air

Jenn-Air JFFCC72EHL01 Bedienungsanleitung

Jenn-Air

Jenn-Air JCD2389DTB Guide Bedienungsanleitung

Jenn-Air

Jenn-Air JUC2450ARW Bedienungsanleitung

Jenn-Air

Jenn-Air JFFCC72EHL Bedienungsanleitung

Jenn-Air

Jenn-Air 2300279A Bedienungsanleitung

Jenn-Air

Jenn-Air JB36NXFXLW00 Bedienungsanleitung

Jenn-Air

Jenn-Air DOUBLE REFRIGERATOR DRAWERS W10310149A Bedienungsanleitung

Jenn-Air

Jenn-Air JSC23C9EEM Bedienungsanleitung

Jenn-Air

Jenn-Air JUBFL242HL Bedienungsanleitung

Jenn-Air

Jenn-Air JBZFR18IGX Bedienungsanleitung

Jenn-Air

Jenn-Air JFC2089HPR10 Bedienungsanleitung

Jenn-Air

Jenn-Air JSD2374ARB Bedienungsanleitung

Jenn-Air

Jenn-Air JBR2086HES Bedienungsanleitung

Jenn-Air

Jenn-Air JFC2290VEP1 Bedienungsanleitung

Jenn-Air

Jenn-Air JS42NXFXDW Bedienungsanleitung

Jenn-Air

Jenn-Air W103039888B Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung