Jenn-Air UKF8001AXX Bedienungsanleitung

TABLE OF CONTENTS

Form No. A/11/04 Part No. 12828126 www.jennair.com Printed in U.S.A.

JENN-AIR BOTTOM FREEZER REFRIGERATOR

USE & CARE

GUIDE

Important Safety Information.........................................1-2

Installation Instructions....................................................3-7

Temperature Controls............................................................8

Fresh Food Features .......................................................9-11

Freezer Features ...................................................................12

Ice and Water..................................................................13-14

Water Filter.......................................................................14-16

Food Storage Tips ..........................................................17-19

Care and Cleaning ........................................................20-23

Operating Sounds ................................................................24

Troubleshooting..............................................................25-27

Warranty...................................................................................31

Guide d’utilisation et d’entretien ....................................32

Guía de uso y cuidado .......................................................64

IMPORTANT SAFETY INSTRUCTIONS

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

WARNING

DANGER – Immediate hazards which WILL result

in severe personal injury or death.

DANGER

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury or property damage.

CAUTION

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this Use & Care

Guide for future reference. This guide provides

proper use and maintenance information.

Keep sales receipt and/or cancelled check as proof

of purchase.

Call: 1-800-JENNAIR (1-800-536-6247)

U.S.A. and Canada

Have complete model and serial number

identification of your refrigerator. This is located on a

data plate inside the refrigerator compartment, on

the upper left side. Record these numbers below for

easy access.

Model Number _______________________________

Serial Number ________________________________

Date of Purchase______________________________

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground) prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

To reduce risk of injury or death, follow basic

precautions, including the following:

IMPORTANT: Child entrapment and suffocation

are not problems of the past. Junked or abandoned

refrigerators are still dangerous – even if they sit out

for “just a few days.” If you are getting rid of your old

refrigerator, please follow the instructions below to

help prevent accidents.

Before you throw away your old

refrigerator or freezer:

•Take off the doors.

•Leave the shelves in place so

children may not easily climb

inside.

DANGER

IMPORTANT SAFETY INSTRUCTIONS

To reduce risk of fire, electric shock, serious injury or

death when using your refrigerator, follow these basic

precautions, including the following:

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not

sure this appliance is properly grounded.

5. Do not ground to a gas line.

6. Do not ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate

115 volt, 15 amp., 60 cycle line.

8. Do not modify plug on power cord. If plug does

not fit electrical outlet, have proper outlet installed

by a qualified electrician.

9. Do not use a two-prong adapter, extension cord

or power strip.

10. Do not remove warning tag from power cord.

11. Do not tamper with refrigerator controls.

12. Do not service or replace any part of refrigerator

unless specifically recommended in Use & Care

Guide or published user-repair instructions. Do

not attempt service if instructions are not under-

stood or if they are beyond personal skill level.

13. Always disconnect refrigerator from electrical

supply before attempting any service. Disconnect

power cord by grasping the plug, not the cord.

14. Install refrigerator according to Installation

Instructions. All connections for water, electrical

power and grounding must comply with local

codes and be made by licensed personnel when

required.

15. Keep your refrigerator in good condition. Bumping

or dropping refrigerator can damage refrigerator

or cause refrigerator to malfunction or leak. If

damage occurs, have refrigerator checked by

qualified service technician.

16. Replace worn power cords and/or loose plugs.

17. Always read and follow manufacturer’s storage

and ideal environment instructions for items being

stored in refrigerator.

18. Your refrigerator should not be operated in the

presence of explosive fumes.

19. Children should not climb, hang or stand on any

part of the refrigerator.

20. Clean up spills or water leakage associated with

water installation.

WARNING

SAVE THESE INSTRUCTIONS

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Location

•Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

•Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

•Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow 1⁄2" space at top and 1⁄2" space behind the

machine compartment cover (located in the rear) for

proper air circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

IMPORTANT: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

•NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging the

refrigerator in immediately may cause damage to

internal parts.

•Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back–NEVER from its front.

•Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

•Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening

restraints may dent or damage outside finish.

Leveling

To protect property and refrigerator from damage,

observe the following:

•Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

•Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be level.

Note

•Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed

•3⁄8" hex head driver

•Carpenter’s level

1. Remove toe grille.

•Grasp firmly and pull outward

to unclip.

2. Remove bottom bracket cover(s).

•Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

•Use slight pressure to pry the

cover loose.

•Continue to maintain

downward pressure to the

notched side of the cover while

swinging it off.

INSTALLATION

ABA

4. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

5. Using the carpenter’s level, make sure front of

refrigerator is 1⁄4" (6 mm) or 1⁄2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

6. Turn stabilizing legs (C) clockwise until firmly

against floor.

7. Freezer drawer models only: Turn adjustment

screws (A) counterclockwise to allow the full

weight of the refrigerator to rest on the stabilizing

legs.

8. Replace bracket cover(s).

•Position cover into the outer edge of the hinge.

•Swing the cover toward the cabinet and snap it

into place.

9. Replace the toe grille.

To avoid electrical shock which can cause severe

personal injury or death, observe the following:

•Disconnect power to refrigerator before removing

doors or drawer. Connect power only after

replacing doors or drawer.

WARNING

To avoid damage to walls and flooring, protect vinyl

or other flooring with cardboard, rugs or other

protective material.

CAUTION

1. Unplug power cord from power source.

2. Remove toe grille and bottom bracket

cover(s) (see page 3).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

4. Unscrew 5⁄16" hex head screws from

top hinge to remove hinge and retain

all screws for later use.

5. Lift refrigerator door from center

hinge pin.

6. For swing freezer door models

only: Hold freezer door while

removing hinge pin with a 5⁄16" hex

head driver. Remove door from

bottom hinge and retain hinge pin

for later use.

For pullout freezer drawer models

only: Remove plastic sleeve, if present.

Remove center hinge pin with a 5⁄16"

hex head driver. Retain hinge pin and

plastic sleeve for later use.

7. Remove Phillips screws to remove

center hinge and retain all screws for

later use.

8. Remove bottom hinge or stabilizing

bracket with 3⁄8" hex head driver and

retain screws for later use. Lift out

bottom hinge pin (on freezer door

models).

9. If your model has a pullout freezer drawer, see

page 5 for drawer removal instructions.

Note

•For proper reinstallation, ensure the “top” marking

on the interior of the toe grille is oriented correctly.

•Align the toe grille mounting clips with the lower

cabinet slots.

•Push the toe grille firmly until it snaps into place.

Note

•Some models only have adjustment screws “A.”

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

3. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

INSTALLATION

Pullout Freezer Drawer

(select models)

To avoid electrical shock which can cause severe

personal injury or death, disconnect power to

refrigerator before removing doors. After replacing

doors, connect power.

WARNING

To prevent accidental child entrapment or

suffocation risk, do not remove the divider in the top

freezer basket.

DANGER

To avoid possible injury, product, or property

damage, you will need two people to perform the

following instructions.

CAUTION

2. While supporting door front,

hook supports into tabs

located on inside of rail.

To Install:

1. Pull both rails out to full

extension.

3. Lower door front into

final position.

4. Replace and tighten Phillips screws that were

removed from each side of rail system (select

models).

5. Place the basket cradles back onto the side rails.

Align snaps with the slots on the side rails and

press each snap towards the rail until it clicks.

6. With rails pulled out to full extension, set the

basket straight down into the basket cradles.

7. Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

Basket cradle

snap attachments

6. Lift top of drawer front

to unhook supports

from rail system. Lift

door front out to

remove.

To Remove:

1. Pull drawer open to full extension.

2. Pull upper basket out to full extension and lift out

to remove.

3. Lift lower basket straight up and out to remove.

4. On each side rail is a

basket cradle with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the side

rail system. Lift the cradles

off of the rails.

5. Remove Phillips screw

from each side of rail

system (select models).

INSTALLATION

Reinstallation of the Doors

1. Install hinge assemblies:

•Install top hinge loosely with 5⁄16" hex head

screws.

•Install center hinge with Phillips screws.

•Freezer door models: Install bottom hinge with

3⁄8" hex head screws.

2. Freezer door models: Insert bottom

hinge pin.

•Locate bottom hinge hole closest to

outside edge of cabinet, and insert

bottom hinge pin. Replace any door

shims, if present.

3. Freezer door models: Place hinge

side of freezer door on bottom hinge

pin and hold freezer door upright

while installing center hinge pin with

5⁄16" hex head driver.

•Replace plastic sleeve.

•Replace any applicable door shims.

•Make sure the hinge pin is installed tightly.

4. Place hinge side of refrigerator

door on center hinge pin.

5. While holding refrigerator door

upright, tighten down top hinge

with 5⁄16" hex head driver and

replace hinge cover.

Door Reversal

In some installations, reversing the door swing allows

for more convenient access to stored items. Both

doors can be reversed on freezer door models and the

fresh food door is reversible on freezer drawer models.

1. Remove door(s) (see page 4).

2. Transfer cabinet plugs and cabinet

screws to opposite side of cabinet.

•Remove cabinet plugs with flat

blade of screwdriver tip wrapped

in masking tape.

•Remove center mullion screws

with 5⁄16" hex head screwdriver.

•Freezer door models: Remove

bottom mullion screws with 3⁄8" hex head driver.

3. Transfer door stops from bottom edge of fresh food

door and freezer door, if applicable, to opposite

side of door edge.

•Use a Phillips screwdriver

for removal and installation.

4. Install handles (see below).

5. Reinstall the door(s).

To avoid possible injury and damage to property:

•Place doors on a nonabrasive surface protected by

towels or rugs while working directly on doors.

CAUTION

Handles

Handle Removal (style varies by model)

Materials Needed:

•3⁄32” allen wrench

To Remove:

•Remove set screw from

handle mounting post

using 3⁄32” allen wrench.

•Repeat the procedure on

all posts to remove the

handle.

To Replace:

•Align handle with the mounting posts.

•Fully tighten all set screws to secure handle

in place.

INSTALLATION

Connecting the Water Supply

(select models)

To reduce the risk of injury or death, follow

basic precautions, including the following:

•Read all instructions before installing ice maker.

•Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

•Observe all local codes and ordinances.

•Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

•Disconnect power to refrigerator before installing

ice maker.

•Water damage due to an improper water

connection may cause mold/mildew growth.

Clean up spills or leakage immediately.

WARNING

To avoid property damage or possible injury,

follow basic precautions, including the

following:

•Consult a plumber to connect 1⁄4” O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

•Confirm water pressure to water valve is between

35 and 100 pounds per square inch. 20 pounds

per square inch if there is not a water filter.

•Do not use a self-piercing, or 3⁄16" saddle valve.

Both reduce water flow and can become clogged

over time; and may cause leaks if repair is

attempted.

•Tighten nuts by hand to prevent cross threading.

Finish tightening nuts with pliers and wrenches.

Do not overtighten.

•Wait 2-3 hours before placing refrigerator into final

position to check and correct any water leaks.

Recheck for leaks after 24 hours.

•Verify the copper tubing under the sleeve is

smooth and free from defects. Do not reuse an old

sleeve.

CAUTION

Materials Needed

•1⁄4" outer diameter flexible copper tubing

•Shut-off valve (requires a 1⁄4" hole to be drilled into

water supply line before valve attachment)

•Adjustable wrench

•1⁄4" hex nut driver

Note

•Add 8' to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2’ diameter).

Avoid kinks in the copper tubing

when bending it into a service

loop.

2. Remove plastic cap from water valve inlet

port.

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve.

4. Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink – so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

IMPORTANT: Do not overtighten. Cross

threading may occur.

6. Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

2’ diameter

minimum

INSTALLATION

TEMPERATURE CONTROLS

Touch Temperature Controls

The controls are located at the top front of the

refrigerator compartment.

Control

Initial Control Settings

After plugging the refrigerator in, set the controls.

•Pressing the or pads adjusts the controls to

the desired setting.

•The temperature control range for both

compartments is 1 through 7 (coldest).

•Set the freezer control on 4.

•Set the refrigerator control on 4.

•Let the refrigerator run at least 8 to 12 hours before

adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

•24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 17

for instructions on checking compartment

temperature.

•Except when starting the refrigerator, do not change

either control more than one number at a time.

•Allow 24 hours for temperatures to stabilize.

Temperature Control Guide

Refrigerator too warm

Refrigerator too cold

Freezer too warm

Freezer too cold

Turn refrigerator OFF

Set the refrigerator control

to next higher number by

pressing the pad.

Set the refrigerator control

to next lower number by

pressing the pad.

Set the freezer control to

next higher number by

pressing the pad.

Set the freezer control to

next lower number by

pressing the pad.

Press the freezer or

refrigerator pad until a

dash “–” appears in the

display.

▲

▼

▲

▼

Shelves

To avoid personal injury or property damage,

observe the following:

•Never attempt to adjust a shelf that is loaded with

food.

•Confirm shelf is secure before placing items on

shelf.

•Handle tempered glass shelves carefully. Shelves

may break suddenly if nicked, scratched, or

exposed to sudden temperature change.

CAUTION

Door Storage

Dairy Center

The Dairy Center provides

convenient door storage for

spreadable items such as butter

and margarine. This compartment can be moved to

different locations to accommodate storage needs. To

use the dairy center, raise the cover.

To Remove:

•Raise the cover, pull upward and tilt out.

To Install:

•Reverse above procedure.

Door Buckets

Door Buckets can be moved to

meet storage needs.

To Remove:

•Slide bucket up and pull straight out.

To Install:

•Slide bucket in and down until firmly seated in the

door liner.

Full-width Door Shelf

Full-width Door Shelf removes for easy cleaning.

To Remove:

•Slide shelf up and pull straight out.

To Install:

•Reverse above procedure.

Your refrigerator has either Spillsaver™ or non-

sealed shelves. The Spillsaver™ shelves have a spill

retainer edge which allows for easier clean up and

some are equipped with the EasyGlide™ slide out

feature. To slide out (select models), grasp the front of

the shelf and pull forward. Push in the shelf to return

to the original position.

To Remove a Shelf:

•Slightly tilt up the front and lift up

the rear of the shelf, then pull the

shelf straight out.

To Lock the Shelf Into Another Position:

•Tilt up the front edge of the shelf.

•Insert the hooks into the desired frame openings and

let the shelf settle into place.

•Be sure the shelf is securely locked at the rear.

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

•Remove crisper drawers as indicated on page 10.

•Place hand under the frame to push up the glass. Lift

glass out.

•Lift frame from refrigerator liner rails.

•To install, repeat above instructions in reverse order.

FRESH FOOD FEATURES

Inhaltsverzeichnis

Sprachen:

Andere Jenn-Air Kühlschrank Handbücher

Jenn-Air

Jenn-Air JS48SEDUDB00 Bedienungsanleitung

Jenn-Air

Jenn-Air jb36ssfxra Bedienungsanleitung

Jenn-Air

Jenn-Air JB36NXFXLW00 Bedienungsanleitung

Jenn-Air

Jenn-Air REFRIGERATOR Bedienungsanleitung

Jenn-Air

Jenn-Air JTB1986ARA Bedienungsanleitung

Jenn-Air

Jenn-Air JCB2388ARA Bedienungsanleitung

Jenn-Air

Jenn-Air JUR24FRERS Bedienungsanleitung

Jenn-Air

Jenn-Air JFFCC72EHL Bedienungsanleitung

Jenn-Air

Jenn-Air JCB2285KEF Bedienungsanleitung

Jenn-Air

Jenn-Air W103039888B Bedienungsanleitung

Jenn-Air

Jenn-Air JUG24FLERS Bedienungsanleitung

Jenn-Air

Jenn-Air JFC2089HPY12 Bedienungsanleitung

Jenn-Air

Jenn-Air C 2300279C Bedienungsanleitung

Jenn-Air

Jenn-Air JS42PPDUDB00 Bedienungsanleitung

Jenn-Air

Jenn-Air JFX2897DRM Bedienungsanleitung

Jenn-Air

Jenn-Air JCB2585WES Bedienungsanleitung

Jenn-Air

Jenn-Air JFC2290VTB10 Bedienungsanleitung

Jenn-Air

Jenn-Air W10292391 Bedienungsanleitung

Jenn-Air

Jenn-Air DOUBLE REFRIGERATOR DRAWERS W10310149A Bedienungsanleitung

Jenn-Air

Jenn-Air W10549548A Bedienungsanleitung

Jenn-Air

Jenn-Air JUC2450ARW Bedienungsanleitung

Jenn-Air

Jenn-Air JS48PPDBDA Leitfaden

Jenn-Air

Jenn-Air JS42PPDUDB01 Bedienungsanleitung

Jenn-Air

Jenn-Air JS42PPDUDB00 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung