Jetboil FLASH Bedienungsanleitung
Cooking System
Instructions
FLASH
Important: Read these warnings and instructions carefully
prior to assembling or using this product. Fully familiarize
yourself with this product before connecting it to a fuel
canister. Keep these instructions for future reference.
WARNING
FIRE OR EXPLOSION HAZARD
If you smell gas:
1. Do not attempt to light appliance
2. Make sure appliance is in the off position.
3. Extinguish any nearby flame(s).
4. Shut off cylinder fuel supply valve if so
equipped, or if equipped with a disposable fuel
cylinder, disconnect cylinder
5. Leave the area immediately.
6. Allow gas to dissipate 5 minutes.
7. If gas smell has dissipated from the area,
of the appliance, and fuel supply, follow gas
connection procedures.
8. If you smell gas again, follow steps 1-6 and
have appliance serviced.
Failure to follow these instructions could result
in fire or explosion, which could cause property
damage, personal injury, or death.
ONLY USE OUTDOORS IN A WELL-VENTILATED AREA IN
ORDER TO AVOID ENDANGERING YOUR LIFE
1
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide
which is poisonous and has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space
such as a camper, caravan, tent, car, mobile
home, marine craft, or home.
FOR YOUR SAFETY
Donot store or use gasoline or other flammable vapors
andliquidsinthevicinityofthis or anyother appliance.
•Donotmodify this appliance.This may be hazardous and will void the warranty.
• Burn Hazard - Accessible parts may become very hot.
• Do not leave this appliance unattended while the appliance is in operation;
keep children and pets away from the appliance at all times
• Improper installation, use, adjustment, alteration, service, or maintenance
can cause injury or property damage. Refer to this manual. For assistance
or additional information consult a qualified installer, service agency or
gas supplier.
DANGER
2
WARNING
TABLE
OF CONTENTS
GENERAL WARNINGS .................1-2
SPECIFICATION ..............................4
LEAK CHECK PROCEDURE .............4
FIGURES .........................................5
ASSEMBLY ......................................6
OPERATING INSTRUCTIONS ......7-8
STORAGE AFTER USE .....................8
MAINTENANCE ..............................8
TROUBLESHOOTING ......................8
FRENCH TRANSLATION ...............10
INTERNATIONAL TRANSLATIONS...19
3
SPECIFICATIONS
LEAK CHECK
PROCEDURE
Gas category: Direct Pressure – Butane-Propane mixture. Canister
must conform to the EN417 or AS2278 standard. This appliance is only
intended for use with 100g/230g/450g Jetboil Jetpower Isobutane/
Propane Fuel Canisters (sold separately). It may be hazardous to
attempt to fit other types of gas containers.
Jet Size: 0.27mm Gas Consumption: 7 MJ/hr (AU) || 139 g/hr [2 kW]
(EU) || 9,000 BTU/hr (CA)
Minimum Storage Temperature: -40°F / -40°C
Minimum Use temperature: 0°F / -20°C
1. Perform leak checks outside, in a well-ventilated area.
2. Connect fuel canister (3.1) to valve (3.2) by threading in the
orientation shown in Fig 4.
3. Put soapy water on the gas connection between fuel canister and
the valve. Formation of bubbles indicate a gas leakage.
Do not check for leaks using a flame.
If a leak is detected, do not attempt ignition. Remove fuel
canister immediately and contact Customer Service.
4. If no leak is found, detach fuel canister. Leak check is complete. 4
FIGURES
Fi
Fi
Fig. 11
Fig. 12
Fi
Fi
Fi Fig. 9
Fi
Fig. 10
Fi
Fi
Fig. 7
Fi
Fig. 4
Fi
Fi
Fig. 3
Fig. 1
Fig. 6
Fi
Fig. 8
Fig. 2
Fig. 5
1.1
5.1
8.2
8.1
11.1
1.31.3
2.2
2.1
2.3
12.2
12.1
1.2
3.2
10.1
10.2
7.2
7.1
3.1
5
DO NOT
HEAT EMPTY
LIGHT BEFORE
ATTACHING
POT
1. Remove packed contents from pot (Fig 1).
2. Perform LEAK CHECK PROCEDURE (See Page 4).
3. Unfold the bail (2.1) from the valve body (2.2).
4. Close the control valve (8.1) (turn clockwise).
5. Check for debris in the valve connection (1.1), and that the O-Ring is in place
and in good condition before connecting to the stove.
Donotusetheapplianceifithasdamagedorwornseals,thismayresultingasleakage.
Intemperatures belowfreezing,O-Ringsmay notsealfully,resultinginafuelleak.
6. To check that the gas canister is not empty, liquid fuel may be heard and/or felt
inside when the canister is shaken.
7. Connect fuel canister (3.1) to valve (3.2) by threading in the orientation shown in Fig
4. Hand tighten only, do not over-tighten or cross-thread. May damage
seals resulting in fuel leak.
8. Unfold stabilizer legs (2.3) and securely attach stabilizer to fuel canister (Fig 5).
9. Place assembled stove on a flat, level surface, at least 1m/3.3ft away from any
combustible materials or ignition sources.
10. If using Pot Support (sold separately): Unfold pot support legs (12.1), place it on top
ofburner baseandrotatetolock(12.2).Confirm thatsupportisfullyattached, seatedandstable.
Never use alternate cookware without the Jetboil Pot Support. Failure to
use the Pot Support will result in a fire that may cause death or serious injury.
Never use cookware larger than 2L capacity or 9in. [23cm]
diameter when using a Pot Support.
ASSEMBLY
• Perform Leak Checks outside, in a well-ventilated area.
• Operate at least 1m/3.3ft away from combustible materials and ignition sources.
• Before each use: Keep stove area clear and free from combustible
materials, gasoline, and other flammable vapors and liquids.
• Do not obstruct the flow of combustion and ventilation air to the stove.
• Do not use windscreen or outback oven; this can overheat the fuel canister,
resulting in explosion.
•Do not use anappliance which isleaking,damaged or which does notoperateproperly.
• Always change gas canisters in a well ventilated location away from any
sources of ignition, such as naked flames, pilot, electric heaters/equipment
and away from other people.
WARNING
6
Preparation:
1. Remove bottom cover (7.1) from bottom of the Jetboil pot (7.2). 2. Remove Pot
Support Warning Tag and Pack Bag (if included). 3. Add contents to the pot, cover
with lid, but do not put the pot on the stove yet. Now you are ready to light the burner.
4. Test igniter by depressing igniter button (8.2) until click is heard. If it does not
spark, refer to Maintenance and Troubleshooting sections.
Performance may be suboptimal if used in extreme conditions
(cold, hot, wind, altitude).
Do not use stove to warm fuel canister. Can result in explosion.
Lighting the Burner:
Ensure burner base is free of any pot prior to lighting. Gas build-up can
occur, resulting in increased flame eruption.
1. Open control valve (8.1) counterclockwise until fully opened and gas flow can be heard.
2. To light, depress Igniter Button (8.2) until click is heard. Repeat as necessary
until ignition (Fig 9). 3. If ignition does not occur within 5 seconds, close control
valves and wait 5 minutes before repeating the procedure.
• Keep burner at arm’s length, away from face, during ignition. Flame can
flare during ignition.
• Do not attempt to light with included pot or any other cookware on the
burner. Gas build-up can occur, resulting in increased flame eruption.
• Never expose stove to flammable vapors or liquids while lighting the burner.
It can cause an explosion or fire.
• Do not heat empty pot. Product will melt and potentially catch fire.
• Do not move, lift, or tilt stove with lit burner. Product damage or injury can
occur due to flaring.
• Do not fill above maximum fill line. This may cause boil-over, resulting in injury.
• If attempting to heat anything other than water, use care and stir frequently
to avoid boil over or scorching, which may result in product damage or injury.
• Always check that the burner is extinguished before disconnecting the fuel canister.
• Do not use for boiling oil or deep frying. Product damage or injury can occur
due to overheating.
OPERATING INSTRUCTIONS
WARNING
Usage:
1. If necessary, rotate control valve (8.1) clockwise to decrease flame setting.
2. Once the burner is lit, carefully place the pot with its contents on the burner
base (Fig 10); turn as shown in Fig 11 to lock into place. 3. Heat indicator: As
the pot heats, the heat indicator (11.1) will turn from Black to Orange. If
the heat indicator is Orange, the pot and its contents are above 149°F (65°C).
7
Use care when removing lid. Steam and/or
contents may be hot and can cause injury.
TRUCTIONS After Use:
1. Turn off control valve (8.1) (tighten clockwise) to
extinguish flame. 2. Remove pot from burner base – hold pot by cozy (10.1), and
base by shroud (10.2).
Exposed metal parts will be hot and may cause injury if touched.
3. Always disconnect fuel canister after use. Unscrew fuel canister from burner
base (Fig 4), and replace plastic fuel cap.
Always check that the burner is extinguished before disconnecting the
fuel canister. Vapors can ignite and cause serious injury.
Packing:
1. Allow stove to fully cool before packing. 2. Place bottom cover (7.1) on pot (7.2).
3. Remove stabilizer from canister and fold for storage (1.2). 4. Fold Valve bail
under valve body (1.3). 5. Ifusing the potsupport: Remove pot support fromburnerbase
(Fig 12), and foldlegs (1.4). 6. Refer to Fig 1 for packing contents into pot.
STORAGE AFTER USE
1. Always disconnect fuel canister before storing the stove. 2. Ensure stove and
pot are clean and dry before storing. 3. Store the stove in a cool, dry location,
indoors.
MAINTENANCE 1. Flame Check (Every use): The height of the flame should
increase from low to high with counter-clockwise rotation of the control valve.
Flame should be blue with no yellow tipping at full output. Flame should not flash
back into burner or lift off of burner top. If flame abnormalities are found, see
your dealer or contact Jetboil for service. 2. Cleaning Pot (before storage, or as
needed): Allow pot to cool before cleaning. Do not use a dishwasher or abrasive
compounds (sand, salt, etc.) to clean. Only wash by hand with soapy water.
TROUBLESHOOTING 1. Flame does not extinguish: Tighten valve as much as
possible, blow out flame, and immediately detach fuel source. See your dealer or
contact Jetboil for service. 2. Igniter fails to spark: If igniter will not spark, check
positioning of electrode in relation to burner. Approximately 1/8” (3mm) length of
igniter wire should protrude from the igniter ceramic. Wire should point toward
center of burner with a 1/8” (3mm) gap between the end of the wire and the top
surface of the burner. If not positioned as described, re-position the electrode
accordingly. Bend wire towards center of burner head and position as described
above. If stove is wet, igniter may fail to spark. If igniter fails to spark, use matches
or a lighter, following instructions detailed in OPERATING INSTRUCTIONS –
Lighting the Burners. See your dealer or contact Jetboil for service if igniter fails
to spark for any other reason. 3. If an issue cannot be corrected using these
instructions, see Limited Warranty on back page.
8
9
Système de
cuisson
FLASH
Important: Lisez attentivement ces avertissements et
instructions avant d’assembler ou d’utiliser ce produit.
Familiarisez-vous avec ce produit avant de le connecter
à une cartouche de combustible. Conservez ces
instructions pour référence ultérieure.
Inhaltsverzeichnis
Sprachen:
Andere Jetboil Kochgeräte Handbücher
