JL Audio M-MCPv3-DM Bedienungsanleitung

Installation Instructions for

M-MCPv3-DM

DECK MOUNTING FIXTURES

FOR ETXv3 ENCLOSED SPEAKER SYSTEMS

Determine the mounting location of the ETXv3

enclosure. Using the holes in the xture base as a guide,

mark the three hole locations, and carefully drill three

3/16” pilot holes and one 1/2” speaker cable hole.

Route the speaker cable exiting the enclosure through

the opening in the other half of the xture, and guide the

tabs into the openings in the xture until ush.

Remove the 5/16 - 18 x 1-1/4” socket head cap screw and

5/16” lock washer to separate the two xture halves. Se-

cure the xture base to the mounting surface using three

#14 x 1-1/4” at head sheet metal screws (included).

Apply Loctite® red thread-locking compound (included)

to the two 5/16 - 18 - 1-1/8” machine screws (included),

thread them into the xture while rmly pushing the

enclosure and xture together to ensure no gap, and

fully tighten.

Route the speaker cable exiting the enclosure through

the hole in the xture base, and align the two xture

halves together.

Use the supplied butt connectors to connect the red (+)

and black (-) speaker cable exiting the ETXv3 enclosure

to the speaker cable below the mounting surface. e

green and white wires will not be used in this application

Rotate the enclosure to the desired angle, install the

5/16 - 18 x 1-1/4” socket head cap screw and 5/16” lock

washer, and fully tighten.

Remove adhesive backing and install the JL Audio logo

badge (Sport Grille Models Only).

If a dierent speaker angle is desired, remove the speaker

mounting screws and washers.

For best adhesion, it is recommended to clean the inside

of the aluminum cap with acetone (not included), prior

to attaching it to the speaker enclosure.

Apply a circular bead of silicone adhesive (included) to

the inside of the aluminum logo cap, about 1/2-inch (13

mm) from the outer edge.

Rotate the speaker to the desired angle. Reinstall the

speaker and speaker mounting screws and washers.

Hand-tighten the screws in a criss-cross pattern.

Align the aluminum logo cap to the desired angle of

rotation, and press it onto the back of the enclosure.

Apply masking tape (not included) to hold the cap in

place until the silicone cures (at least 24 hours).

FLEXIBLE MOUNTING OPTIONS

Deck Mounting Suspended Mounting

NOTE: The MCPv3-DM fixture and M770-ETXv3-SG-WH Enclosed Speaker

System are used in this manual for illustrative purposes only. The fixture

installation steps are the same for all ETXv3 Enclosed Speaker Systems and

the M-MCPv3- Deck-Mount Fixture listed on front cover.

LIMITED WARRANTY  MARINE PRODUCTS USA

JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the

original date of purchase.

This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service

be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),

repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not

covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,

unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages

and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not

covered under warranty.

Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning

with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product

thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For Service Information in the U.S.A. please call

JL Audio Customer Service: (954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc

10369 North Commerce Pkwy.

Miramar, FL 33025, USA

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

w w w . j l a u d i o . c o m

JL Audio® and the JL Audio logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

©2014 JLAudio, Inc. • For more detailed information please visit us online at www.jlaudio.com. Due to our policy of continuous product development, all specifications are subject to change without notice.

SKU# 011420

Printed in U.S.A. • 032515

Andere JL Audio Rack & Stand Handbücher