JL Audio SlamPak SLPK-YA-19FXC Bedienungsanleitung

INSTALLATION GUIDE

for the

SLPK-YA-19FXC

SKU# 94670 & 94671

SLPK-YA-19FXC-SUB

SKU# 94674

2019-Up Yamaha FX

Thank you for choosing a JL Audio SlamPak™ for your marine sound system.

With proper installation, your new marine audio sound system

will deliver years of listening pleasure.

We strongly recommend that you have your new SlamPak™ installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vessel properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the SlamPak™ be properly mounted to the vessel

according to these instructions. Failure to mount the enclosures

properly presents two problems:

1) A loose enclosure presents a serious safety hazard in the event of a

collision, rollover, or sudden deceleration.

2) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

INSTALLATION

DIFFICULTY:

ESTIMATED TIME:

34 HOURS

Continued on Next Page

OUT

SlamPak™

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

MX600/3 Amplifier (x1) VEX Speaker Enclosure (x2) 50A Circuit Breaker (x1)

Rear Logo Appliqué (x2)

Port VEX Adaptor (x1)

Starboard VEX Adaptor (x1)

Port VEX Adaptor Gasket (x1)

Starboard VEX Adaptor Gasket (x1) Back Plate (x2) Amplifier Bracket (x1)

7/16 - 14 x 7/8” Stainless Steel

Hex Head Bolt (x4)

7/16” Stainless Steel

Split Lock Washer (x4)

8-32 Stainless Steel

Flat Washer (x3)

8-32 Stainless Steel

Locknut (x3)

1/4 - 20 x 1” Stainless Steel

Hex Cap Screw (x8)

1/4” Stainless Steel

Flat Washer (x10)

1/4” Stainless Steel

Oversized Flat Washer (x6)

1-4 - 20 Stainless Steel

Nylon Insert Locknut (x8) 11” Cable Ties (x10)

INCLUDED HARDWARE

Continued on Next Page

Page 2 • JL Audio, Inc., 2020

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

SLPK-YA-19FXC Equipment and Hardware

M6 - 1 x 20mm Stainless Steel

Socket Cap Screw (x4)

MBT-CRXv2

Bluetooth Controller (x1)

NOTE: For optimum performance

and reliability, all amplifier controls

have been preset for this SlamPak™

and sealed beneath the control

panel cover. No further adjustment

is necessary.

INCLUDED HARDWARE

Continued on Next Page

Page 3 • JL Audio, Inc., 2020

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

SLPK-YA-19FXC Equipment and Hardware (cont.)

SLPK-YA-19FXC-SUB Equipment and Hardware

Clear Sheet

Drilling Template (x1)

NOT SHOWN

Power Harness (x1)

Amplifier Harness (x1)

1.5’ 2-Channel

RCA Interconnect (x1)

8 AWG Power Cable Extension (x1)

Subwoofer Enclosure (x1) Long Bracket (x2) Short Bracket (x2) Latch Bracket (x1)

#6 x 1/2” Stainless Steel

Pan Head Screw (x4)

5/16 - 18 x 1” Stainless Steel

Hex Head Bolt (x4)

5/16” Stainless Steel

Split Lock Washer (x4)

5/16” Stainless Steel

Flat Washer (x4) Loctite® Threadlocker (x1)

Loctite® Threadlocker (x1)

2-Pack 1” Heat Shrink (x1)

2-Pack 2” Heat Shrink (x2)

Page 4 • JL Audio, Inc., 2020 Continued on Next Page

STEP 8

Remove the three indicated screws from the

accent panel on the port side, then remove the

nut from the inside of the hull.

STEP 7

Remove the indicated front bolt and nut and

the rear screw from the body panel on the port

side.

STEP 6

The lower access panel has been removed.

STEP 5

Unlatch and lift the lid. Remove the two

indicated push clips from the starboard side

of the lower access panel. Repeat for the two

push clips on the port side, and remove the

panel.

STEP 4

Open the center storage compartment, and

carefully unclip and remove the storage

compartment lid.

STEP 3

Remove the front seat section from the vessel.

STEP 2

Remove the under seat locker.

STEP 1

NOTE: This manual includes installation

steps for the SLPK-YA-19FXC speaker kit and

the SLPK-YA-19FXC subwoofer enclosure

add-on. Please take the time to read this

manual thoroughly to familiarize yourself

with the installation steps for your

application.

Unlatch and remove the rear seat section from

the vessel.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Page 5 • JL Audio, Inc., 2020 Continued on Next Page

STEP 16

Remove the four screws from around the

steering column cover panel.

STEP 15

Remove the lower handle bar cover panel from

the vessel.

STEP 14

Remove the upper handle bar cover panel from

the vessel.

STEP 13

Remove the eleven screws from the lower

handle bar cover panel.

STEP 12

Remove the two bolts from under the upper

access panel, and remove the panel from the

vessel.

STE P 11

Remove the body panel from the vessel.

Remove the indicated screw from the front of

the console, and repeat for the screw on the

opposite side.

Repeat Steps 7-11 for the starboard side.

STEP 10

Remove the two indicated screws from the top

of the body panel on the port side.

STEP 9

Remove the accent panel from the vessel.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Page 6 • JL Audio, Inc., 2020 Continued on Next Page

STEP 24

Enlarge the forward hole using a 1/4” drill bit.

STEP 23

Using a 1/16” drill bit, carefully drill through

each of the three marks on Template A and into

the hull.

Carefully remove Template A from the vessel.

STEP 22

Carefully cut Template A from the clear sheet

on the indicated line.

Align Template A with the bottom of the

induction box on the port side, and tape it into

position.

STEP 21

Carefully remove the console from the vessel

by guiding the handle bar and throttle control

through the center opening.

STEP 20

From under the console, unplug the main

harness and the Menu Scroll / Alarm Mute

switch.

STEP 19

Remove the four handle bar bolts, and carefully

set the handle bar to the side.

STEP 18

Remove the throttle control from the handle

bar and carefully set it to the side.

STEP 17

Remove the four screws from the throttle

control.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Page 7 • JL Audio, Inc., 2020 Continued on Next Page

STEP 32

With the rivet removed, enlarge the hole in the

induction box mounting tab and the hull to

1/4”.

STEP 31

Using a 3/16” drill bit, carefully drill through the

rivet head and remove the rivet.

STEP 30

Use a center punch to tap in the center of the

lower rivet on the induction box on the port

side.

STEP 29

Ensure the Amplifier Bracket is aligned with

the induction box. Using a 1/4” drill bit and the

upper mounting hole on the Amplifier Bracket

as a guide, carefully drill through the hull.

Remove the 1/4 - 20 x 1” Hex Cap Screw and

the Amplifier Bracket from the vessel.

STEP 28

Slide a 1/4 - 20 x 1” Hex Cap Screw through the

lower mounting hole on the Amplifier Bracket,

into the hull.

STEP 27

Using a 1/4” drill bit and the lower mounting

hole on the Amplifier Bracket as a guide,

carefully drill through the hull.

STEP 26

Align the Amplifier Bracket to the back of the

induction box on the port side.

STEP 25

Enlarge the other two holes using a 7/16” drill

bit.

Repeat Steps 22-25 on the starboard side.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Page 8 • JL Audio, Inc., 2020 Continued on Next Page

STEP 40

Pull the factory junction box panel off of the

firewall.

STEP 39

Remove the two bolts from the side of the

factory junction box panel. Repeat for the

opposite side.

STEP 38

Route the Power Harness down the inside of

the hull on the starboard side, toward the

battery. Use Cable Ties to secure the Power

Harness to the factory wiring.

STEP 37

Loosen the factory cable tie below the console

grommet on the hull, and pass the Power

Harness down through the grommet until

approximately 19” of the connector end remain

exposed above.

STEP 36

From inside the hull, secure the Amplifier

Bracket to the vessel using a 1/4” Oversized

Flat Washer and a 1/4 - 20 Nylon Insert Locknut

over each 1/4 - 20 x 1” Hex Cap Screw, and fully

tighten.

STEP 35

Align the Amplifier Bracket to the vessel. Slide

a 1/4” Flat Washer over each of two 1/4 - 20 x 1”

Hex Cap Screws. Apply Loctite® Threadlocker

to each, and pass an assembly through the

mounting holes in the Amplifier Bracket,

through the holes drilled in Steps 27 & 29.

STEP 34

From inside the hull, align the outer holes in a

Back Plate with the hardware installed in the

previous step. Ensure the curved side of the

Back Plate is oriented upward. Secure the Back

Plate using a 1/4” Oversized Flat Washer and a

1/4 - 20 Nylon Insert Locknut over each 1/4 - 20

x 1” Hex Cap Screw, and fully tighten.

Repeat Steps 30-34 on the starboard side.

STEP 33

Slide a 1/4” Flat Washer over each of two

1/4 - 20 x 1” Hex Cap Screws. Apply Loctite®

Threadlocker to each, and pass an assembly

through each of the indicated holes drilled in

Steps 24 & 32.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Page 9 • JL Audio, Inc., 2020 Continued on Next Page

STEP 48

Connect the Power Harness to the Amplifier,

and secure with Cable Ties.

STEP 47

Connect the Amplifier Harness to the Amplifier.

Slide a piece of 2” Heat Shrink Tubing over each

channel of the RCA Interconnects, and

connect to the Front Input jacks of the

Amplifier Harness. Carefully cut the red and

white protective caps from the Front Input

jacks of the Amplifier Harness. Position the 2”

Heat Shrink Tubing over the joined

connections, and use a heat gun or torch to

shrink the tubing.

STEP 46

Align the Amplifier over the studs on the

Amplifier Bracket with the wiring exiting the

Amplifier toward the rear.

Secure the Amplifier to the Amplifier Bracket

using three 8-32 Washers and 8-32 Locknuts,

and fully tighten.

STEP 45

Connect the opposite end of the 8 AWG Power

Cable Extension to the positive battery

terminal and connect the ground cable from

the Power Harness to the negative battery

terminal. Secure cables with Cable Ties.

STEP 44

Press the red button on the Circuit Breaker to

disengage it.

Connect the positive power cable to one side

of the Circuit Breaker and the 8 AWG Power

Cable Extension to the other side.

STEP 43

Slide a 1/4” Flat Washer over each of two 1/4 -

20 x 1” Hex Cap Screws, and pass an assembly

through each of the mounting holes in the

Circuit Breaker, through the holes drilled in the

previous step. Secure the Circuit Breaker to the

fire wall using a pair of 1/4” Flat Washers and

1/4 - 20 Nylon Insert Locknuts on the front side

of the fire wall, and fully tighten.

Reinstall the factory junction box panel.

STEP 42

Using a 1/4” drill bit, carefully drill through each

of the marks made in the previous step.

STEP 41

Align the Circuit Breaker along the upper edge

of the back side of the fire wall. Using the

Circuit Breaker as a template, mark the

locations of the mounting holes.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Page 10 • JL Audio, Inc., 2020 Continued on Next Page

STEP 56

Align the lower slots in the Short Brackets with

the factory holes in the hull.

Thread the factory bolts removed in Step 49

through the slots in the Short Brackets, into the

factory inserts, and hand tighten.

STEP 55

Place the subwoofer enclosure onto the vessel.

Align the lower slots in the Long Brackets with

the factory holes in the hull.

Thread the factory bolts removed in Step 49

through the slots in the Long Brackets, into the

factory inserts, and hand tighten.

STEP 54

Align the short end of a Short Bracket to a

threaded insert on the lower front of the sub-

woofer enclosure.

Pass a 1/4” Flat Washer over a 1/4 - 20 x 1”

Hex Cap Screw. Apply Loctite® Threadlocker,

thread the assembly through the slot in the

Short Bracket, into the threaded insert in the

subwoofer enclosure, and hand tighten. Repeat

the process for the opposite side.

STEP 53

Align the wide end of a Long Bracket to a

threaded insert on the lower side of the

subwoofer enclosure.

Pass a 1/4” Flat Washer over a 1/4 - 20 x 1”

Hex Cap Screw. Apply Loctite® Threadlocker,

thread the assembly through the slot in the

Long Bracket, into the threaded insert in the

subwoofer enclosure, and hand tighten. Repeat

the process for the opposite side.

STEP 52

Remove the four #6 x 1/2” Pan Head Screws

and Latch Bracket from the subwoofer

enclosure. Slide the latch into the recess at

the rear of the subwoofer enclosure. Apply

Loctite® Threadlocker to the four #6 x 1/2” Pan

Head Screws, and reinstall the Latch Bracket,

ensuring the center tab is oriented downward.

Secure the Latch Bracket to the subwoofer

enclosure, and fully tighten.

STEP 51

Carefully pry the rubber latch from the center

storage compartment.

STEP 50

Remove the center storage compartment from

the vessel.

STEP 49

NOTE: Steps 49-56 are used for the

installation of the subwoofer (SLPK-YA-

19FXC-SUB, sold separately). For

installations without a subwoofer, skip

ahead to Step 57.

Remove the two indicated screws from each

side of the center storage compartment.

SLPK-YA-19FXC / SLPK-YA-19FXC-SUB INSTR_SKU# 011531

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JL Audio Sprecher Handbücher

JL Audio

JL Audio C1-570X Bedienungsanleitung

JL Audio

JL Audio Evolution XR650-CS Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-J-WRUP/10TW1 Bedienungsanleitung

JL Audio

JL Audio VR690-CXi Bedienungsanleitung

JL Audio

JL Audio VR525-CXi Bedienungsanleitung

JL Audio

JL Audio TR690-TXi Bedienungsanleitung

JL Audio

JL Audio TR570-CXi Bedienungsanleitung

JL Audio

JL Audio MX650-CCX-SG Bedienungsanleitung

JL Audio

JL Audio M6-650X Bedienungsanleitung

JL Audio

JL Audio JL AUDIO Evolution TR350-CXi Bedienungsanleitung

JL Audio

JL Audio C1-100CT Bedienungsanleitung

JL Audio

JL Audio C1-400x Bedienungsanleitung

JL Audio

JL Audio C2-075ct Bedienungsanleitung

JL Audio

JL Audio PAVILION PV-FX6 Bedienungsanleitung

JL Audio

JL Audio SB-F-EXPL3 Bedienungsanleitung

JL Audio

JL Audio TR525-CXi Bedienungsanleitung

JL Audio

JL Audio C1-690TX Bedienungsanleitung

JL Audio

JL Audio PS-SWMCP Bedienungsanleitung

JL Audio

JL Audio C1-690X Bedienungsanleitung

JL Audio

JL Audio C1-525x Bedienungsanleitung

JL Audio

JL Audio TR570-CXi Bedienungsanleitung

JL Audio

JL Audio M6-650 Series Bedienungsanleitung

JL Audio

JL Audio M3-770x Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-F-MUSCPE/12TW3 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung