JL Audio SlamPak SLPK-YA-VXWR-SG-TB Bedienungsanleitung

INSTALLATION

DIFFICULTY:

ESTIMATED TIME:

34 HOURS

Continued on Next Page

OUT

SLPK-YA-VXWR-SG INSTR_SKU# 011494

INSTALLATION GUIDE

for the

SLPK-YA-VXWR-SG-TB

SKU# 94652

SLPK-YA-VXWR-SG-WH

SKU# 94653

2015-2019 Yamaha VX

SlamPak™Thank you for choosing a JL Audio SlamPak™ for your marine sound system.

With proper installation, your new marine audio sound system

will deliver years of listening pleasure.

We strongly recommend that you have your new SlamPak™ installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vessel properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the SlamPak™ be properly mounted to the vessel

according to these instructions.

Failure to mount the enclosures presents a serious safety hazard in

the event of a collision, rollover, or sudden deceleration.

INCLUDED HARDWARE

Continued on Next Page

Page 2 • JL Audio, Inc., 2020

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Qty Description

1Amp Bracket

1Starboard Adaptor

1Port Adaptor

2 Mounting Insert

1Template

4 8 - 32 x 1/4” Phillips Pan Head Screw

31/4 - 20 x 1” Serrated Flange Bolt

3 1/4” Oversized Flat Washer

5 1/4 - 20 Nylon Locknut

2 1/4 - 20 x 1” Hex Head Bolt

4 1/4” Flat Washer

12 M6 - 1mm x 10mm Phillips Flat Head Screw

27/16 - 14 x 1-1/4” Hex Head Bolt

2 7/16” Flat Washer

2 7/16” Split Lock Washer

22-Pin Female Receptacle

2 2-Pin Wedgelock

1 4-Pin Female Receptacle

1 4-Pin Wedgelock

2 Rubber Grommet

10 Cable Tie

4 Heat Shrink Tubing

Hardware Equipment

Qty Description

1 MX280/4 Amplier *

2VeX Speaker Enclosures

1 MBT-CRXv2 Bluetooth Controller

1 Power Harness

1 Amplier Harness

1 1.5’ Two-Channel RCA Interconnect

1 40A Circuit Breaker

1 Sport Grille Badges (pair)

2 Rear Logo Appliqué

* NOTE: For optimum performance and reliability, all amplifier controls

have been preset for this SlamPak™ and sealed beneath the control

panel cover. No further adjustment is necessary.

Page 3 • JL Audio, Inc., 2020 Continued on Next Page

STEP 8

Remove the body panel from the vessel.

STEP 7

Lift the lid. Remove the indicated bolt and the

nut from the underside.

STEP 6

Remove the indicated screw.

STEP 5

Carefully unclip and remove the screw cover

panel.

STEP 4

Remove the accent panel from the vessel.

STEP 3

Remove the two indicated screws from the

accent panel on the starboard side.

STEP 2

Remove the front seat section from the vessel.

STEP 1

Unlatch and remove the rear seat section from

the vessel.

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Page 4 • JL Audio, Inc., 2020 Continued on Next Page

STEP 16

Connect the Power Harness to the Amplifier.

STEP 15

Loosen the factory cable tie in the grommet in

front of the Amp Bracket. Pass the ring terminal

end of the Power Harness through the

grommet, leaving approximately 12” exposed,

and tighten the cable tie.

STEP 14

Place the Amp Bracket back into position. Pass

a 1/4 - 20 x 1” Serrated Flange Bolt through

each of the mounting holes in the Amp Bracket

and holes drilled in Step 12.

From inside the hull, slide a 1/4” Oversized Flat

Washer and 1/4” Nylon Locknut over each of

the three 1/4 - 20 x 1” Serrated Flange Bolts,

and firmly tighten.

STEP 13

With the Amplifier oriented as shown, with

the wiring toward the rear of the Amp Bracket,

secure the Amplifier to the Amp Bracket using

four #8 - 32 x 1/4” Phillips Pan Head Screws.

STEP 12

Using a 1/4” drill bit, carefully drill through the

three marks made in the previous step.

STE P 11

Mark the three Amp Bracket mounting hole

locations, and remove the Amp Bracket.

STEP 10

Align the edges on the rear of the Amp Bracket

with the edges of the factory bracket, as

shown.

STEP 9

Open the storage compartment, and remove

the insert.

Place the Amp Bracket on the vessel, as shown.

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Page 5 • JL Audio, Inc., 2020 Continued on Next Page

STEP 24

Using a 1/4” drill bit, carefully drill a pilot hole

through the mark made in the previous step.

STEP 23

Carefully cut Template A from the clear sheet

on the indicated line. Align the Template A

with the top of the upper panel, as shown, and

mark the hole location. Remove Template A.

STEP 22

Secure the pins by inserting the Wedgelock

from the front of the 4-Pin Female Receptacle,

as shown.

STEP 21

Insert the wires from the MBT-CRXv2 into the

4-Pin Female Receptacle by sliding each pin

into the rear of the connector, as shown. Pay

close attention to the wire colors and

corresponding pin locations, as listed below:

Pin 1 = Red Pin 4 = Blue/White

Pin 2 = Black Pin 3 = Blue

STEP 20

Securely mount the Circuit Breaker to the

battery tray using a pair of 1/4 - 20 x 1” Hex

Head Bolts with 1/4” Flat Washers from the

inside of the tray and 1/4” Flat Washers and 1/4

- 20 Nylon Locknuts on the outside of the tray.

Press the red button on the Circuit Breaker to

disengage it. Connect the positive power wire

to one side and the 8 AWG extension to the

other side.

STEP 19

Align the Circuit Breaker with the battery tray,

as shown, and mark the mounting hole

locations.

Using a 1/4” drill bit, carefully drill through the

marks.

STEP 18

Disconnect the battery, and remove the

battery from the battery tray.

STEP 17

Route the Power Harness down the starboard

side of the vessel toward the battery, securing

it with existing cable ties.

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Page 6 • JL Audio, Inc., 2020 Continued on Next Page

STEP 32

Remove the trim panel from the body panel

removed in Step 8.

Carefully cut Template B from the clear sheet

on the indicated line. Align Template B to the

back of the trim panel, as shown, and mark the

two hole locations. Remove Template B.

Using a 1/4” drill bit, carefully drill through the

marks for Hole 1 and Hole 2.

STEP 31

Using a 15/32” drill bit, enlarge the adjacent

hole.

STEP 30

Locate the rivet below the induction tube. Use

a center punch to tap in the center of the rivet,

then carefully drill through the rivet head using

a 1/8” drill bit.

Remove the factory threaded insert bracket

from inside the hull.

STEP 29

Secure the Amplifier Harness and Power

Harness with the Marine Cable Ties, leaving

access to the two speaker connectors.

Important: Do not position any Cable Ties

within 2” of the connectors.

STEP 28

Connect the Amplifier Harness to the

MBT-CRXv2 wiring. Slide a piece of Heat Shrink

Tubing over each RCA interconnects, and plug

the interconnects into the MBT-CRXv2

wiring. Using a heat gun or torch, shrink the

Heat Shrink Tubing over the RCA connections.

STEP 27

Connect the Amplifier Harness to the Amplifier.

Using a utility knife, carefully cut the red and

white protective caps from the Front Input jacks

of the Amplifier Harness. Trim each cut flush with

the plastic outer body of each RCA jack. Slide a

piece of Heat Shrink Tubing over each channel of

the RCA interconnects and connect to the Front

Input jacks of the Amplifier Harness. Position the

Heat Shrink Tubing over the joined connections,

and use a heat or torch to shrink the tubing.

STEP 26

Add the thick round gasket to the MBT-CRXv2

controller, aligning the small hole in the

gasket with the alignment pin on the back of

the controller, and guide the controller’s wiring

through the hole drilled in the previous step.

From the underside, add the thin round gasket,

then secure the MBT-CRXv2 using the threaded

fastening collar. Reference the illustration in

the MBT-CRXv2 owner’s manual for details.

STEP 25

Using a 1-1/8” hole saw, enlarge the pilot hole

drilled in the previous step.

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Hole 1 Hole 2

Page 7 • JL Audio, Inc., 2020 Continued on Next Page

STEP 40

Pass the speaker cable exiting the Speaker

Enclosure through the Rubber Grommet, as

shown, and align the Starboard Adaptor on the

Speaker Enclosure with the Hole 2 in the trim

panel.

STEP 39

Install a Rubber Grommet into Hole 1 in the

trim panel, and reattach the trim panel to the

body panel.

STEP 38

Align the Starboard Adaptor to the Mounting

Insert installed in the previous step with the

indicated notch facing opposite the speaker,

and secure using three M6 - 1 x 10mm Phillips

Flat Head Screws.

STEP 37

Align a Mounting Insert to the Speaker

Enclosure, and secure using three M6 - 1 x

10mm Phillips Flat Head Screws.

STEP 36

Using a 15/32” drill bit, enlarge the recessed

factory hole.

STEP 35

Using a 3/4” hole saw, enlarge the copied Hole

1in the body panel.

STEP 34

Reattach the trim panel to the body panel.

Using a 1/4” drill bit and Hole 1 as a guide,

copy the location of Hole 1 onto the body

panel.

Remove the trim panel from the body panel.

Using a 3/8” drill bit, enlarge Hole 1 in the trim

panel.

STEP 33

Using a 1-5/8” hole saw, enlarge ONLY Hole 2.

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Hole 1

Hole 2

Hole 1

Hole 2

Page 8 • JL Audio, Inc., 2020 Continued on Next Page

STEP 48

Remove the six #8 x 1-1/4” Pan Head Screws

and #8 Flat Washers, rotate the speaker to the

desired angle, and reinstall.

STEP 47

Reinstall the accent panel and the two screws

removed in Step 3, and fully tighten.

STEP 46

Fully tighten the screw reinstalled in Step 41,

and reinstall the screw cover panel.

STEP 45

Reinstall the bolt and nut removed in Step 7.

STEP 44

Slide a 7/16” Flat Washer and 7/16” Split Lock

Washer over a 7/16 - 14 x 1-1/4” Hex Head

Bolt. From inside the hull, pass the assembly

through the hole drilled in Step 29, thread

the 7/16 - 14 x 1-1/4” Hex Head Bolt into the

Starboard Adaptor on the Speaker Enclosure,

and hand tighten.

STEP 43

Reinstall the body panel onto the vessel, and

hand tighten the screw removed in Step 6.

STEP 42

Secure the pins by inserting the Wedgelock

from the front of the 2-Pin Female Receptacle,

as shown.

STEP 41

Insert the speaker cable from the Speaker

Enclosure into the 2-Pin Female Receptacle by

sliding each pin into the rear of the connector,

as shown. Pay close attention to the wire colors

and pin locations, as listed below:

Pin 1 = White with (+)

Pin 2 = White

SLPK-YA-VXWR-SG INSTR_SKU# 011494

Page 9 • JL Audio, Inc., 2020

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new SlamPak™!

SLPK-YA-VXWR-SG INSTR_SKU# 011494

STEP 52

Reinstall the battery. Connect the ground cable

from the Power Harness to the negative

battery terminal and the power cable from the

Circuit Breaker to the positive battery terminal.

STEP 51

Repeat Steps 28-48 for the port side.

STEP 50

Remove the adhesive backing from the Rear

Logo Appliqué. With the logo positioned at the

desired angle, attach the Rear Logo Appliqué,

gently pressing on the center to remove any air

pockets.

STEP 49

Remove the adhesive backing from the JL

Audio Logo Sport Grille Badge, and install the

badge onto the speaker grille.

All specifications are subject to change without notice. “JL Audio®” and “How we play®” are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo are trademarks

of JL Audio, Inc.

(954) 443-1100

www.jlaudio.com

JLA-SKU# 011494 • ver. 07.15.2020 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

SPECIFICATIONS

SPEAKERS

Continuous Power Handling (RMS): 60 watts

Nominal Impedance: 4 ohms

Frequency Response: 100 Hz - 25 kHz +/- 3 dB

STEP 54

Reinstall the insert into the storage pocket, and

reinstall both seat sections.

Refer to the MBT-CRXv2 owner’s manual to pair

your mobile device.

STEP 53

Press in on the yellow arm of the Circuit

Breaker to engage it.

Dieses Handbuch passt für folgende Modelle

Andere JL Audio Sprecher Handbücher

JL Audio

JL Audio MX650-CCX-SG Bedienungsanleitung

JL Audio

JL Audio C1-690X Bedienungsanleitung

JL Audio

JL Audio PS-SWMCP Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-F-MUSCPE/12TW3 Bedienungsanleitung

JL Audio

JL Audio Evolution XR650-CS Bedienungsanleitung

JL Audio

JL Audio C1-075ct Bedienungsanleitung

JL Audio

JL Audio C1-650X Bedienungsanleitung

JL Audio

JL Audio TR650-CXI Bedienungsanleitung

JL Audio

JL Audio TR050-CT Bedienungsanleitung

JL Audio

JL Audio TR570-CXi Bedienungsanleitung

JL Audio

JL Audio C2-075ct Bedienungsanleitung

JL Audio

JL Audio C7-350cm Bedienungsanleitung

JL Audio

JL Audio JLTR400CXi Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-J-WRUD Bedienungsanleitung

JL Audio

JL Audio TR525-CXi Bedienungsanleitung

JL Audio

JL Audio C1-400 series Bedienungsanleitung

JL Audio

JL Audio M6-650X Bedienungsanleitung

JL Audio

JL Audio PAVILION PV-FX6 Bedienungsanleitung

JL Audio

JL Audio C1-525x Bedienungsanleitung

JL Audio

JL Audio JLVR600CXi Bedienungsanleitung

JL Audio

JL Audio TR690-TXi Bedienungsanleitung

JL Audio

JL Audio Fathom f112 Bedienungsanleitung

JL Audio

JL Audio JL AUDIO Evolution TR350-CXi Bedienungsanleitung

JL Audio

JL Audio C1-570X Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung