JL Audio 94657 Bedienungsanleitung
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
DIFFICULTY:
ESTIMATED TIME:
12 HOURS
Continued on Next Page
25
OUT
OF
SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502
INSTALLATION GUIDE
for the
SB-POL-GNRLSPKR/MX650
SKU# 94657
2016 & Up Polaris General
Enclosure Type: Sealed
Driver Type: MX650-CCX-SG-TLD-B
Nominal Impedance: 4 ohms
Continuous Power Handling: 60 watts (RMS method)
INCLUDED HARDWARE / WIRING INFORMATION
Continued on Next Page
Page 2 • JL Audio, Inc., 2017
SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
(hardware pictured for one)
Wire Size Wire Color Use
16 AWG Red/Stripe Speaker Positive (+)
Black/Stripe Speaker Negative (-)
20 AWG
Red Not Used
Green Not Used
Blue LED Positive (+)
Yellow LED Negative (-)
BOM ID Qty SKU Description
1 2 152414 Wire Harness (10’)
2 2 153729 1/4 - 20 x 1” Serrated Flange Head Bolt
3 2 153817 1/4” Stainless Steel Flat Washer
4 2 153815 1/4 - 20 Nylon Insert Locknut
- 1 150778 Fuse & Fuse Holder Kit (not shown)
- 1 150249 Foam Tape (not shown)
LED Wire Connections
• For short-circuit protection, install a supplied fuse holder onto EACH
speaker’s BLUE (+12V) LED power connection lead.
• Connect all BLUE (+12V) leads together (parallel) and connect to a
switched +12V supply. Connect all YELLOW (GRD) leads together and
connect to a negative ground or to the NEGATIVE battery post.
• We recommend activating the speakers’ LEDs thru a lighting circuit that
supplies +12V via an existing switch. If an existing switched circuit is
not available, you may install a dedicated toggle/rocker style switch that
will supply positive (+12V) power. Fuse this connection according to how
many LED circuits you have (LED circuits x 150A).
[GND]
LED
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
Fuse
Fuse
Fuse
[GND]
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
LED
LED
LED
Fuse
Fuse
Fuse
Fuse
Fuse
Diagram shows one speaker pair of
LED circuits connected in parallel.
POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX280/4. The diagram below shows the recommended crossover settings for the MX280/4. For a detailed description of the ampli-
er settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2017
SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502
Page 4 • JL Audio, Inc., 2017 Continued on Next Page
STEP 8
From the outside of the vehicle, slide a 1/4” Flat
Washer and 1/4 - 20 Nylon Insert Locknut over
each of the 1/4 - 20 x 1” Serrated Flange Head
Bolts, and hand tighten.
STEP 7
Slide a 1/4” Flat Washer over each of two 1/4
- 20 x 1” Serrated Flange Head Bolts. Pass an
assembly through each of the two indicated
holes in the enclosure and through the plastic
panel to the outside of the vehicle.
STEP 6
Pass the cable exiting the enclosure through
the larger hole in the plastic panel. Position the
speaker enclosure flush against the kick panel,
allowing the grommet to sit in the drilled hole.
STEP 5
Pass the Wiring Harness into the enclosure
through the larger hole. Slide the Seal Nut
over the wiring, thread it over the pre-installed
Liquid Tight Wire Seal, and fully tighten.
STEP 4
Using a 1/4” drill bit, carefully drill through the
center of each of the marks made in the
previous step.
Using a 1-1/8” hole saw, enlarge only the hole
for the larger mark.
Remove the masking from the plastic panel.
STEP 3
Mark the location of each of the four holes in
the speaker enclosure onto the masked panel.
Note that one of the holes is larger than the
other three.
Remove the speaker enclosure from the
vehicle.
STEP 2
Place the speaker enclosure into position, flush
against the kick panel, as shown.
STEP 1
The following steps show the installation
procedure for the driver’s side only, but the
procedure is the same for both sides.
Empty the driver’s side of the vehicle, and
mask the plastic panel in the kick panel area, as
shown.
SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502
Page 5 • JL Audio, Inc., 2017
RECOMMENDED SUBWOOFER SOLUTIONS
The SB-POL-GNRL/10TW3 Stealthbox® subwoofer enclosure is also available for your vehicle. The weatherproof
enclosure is designed for a perfect t and houses a premium JL Audio subwoofer.
SB-POL-GNRL/10TW3
SKU# 94656
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
SB-POL-GNRLSPKR/MX650 INSTR_SKU# 011502
STEP 10
Slide a 1/4” Flat Washer and 1/4 - 20 Nylon
Insert Locknut over the 1/4 - 20 x 1” Serrated
Flange Head Bolt, and fully tighten all three
sets of hardware.
Route the cable as necessary. Refer to Page 2
for wiring information.
STEP 9
Slide a 1/4” Flat Washer over a 1/4 - 20 x 1”
Serrated Flange Head Bolt, and pass the
assembly through the indicated hole in the
plastic panel and into the enclosure.
ST E P 11
Connect and install the speaker. Remove the
adhesive backing, and install the JL Audio logo
badge.
Repeat the process for the passenger side.
Note: For optimum performance, we
recommend applying the included Foam Strips
(or sound damping material) to surrounding
plastic panels to reduce unwanted vibrations.
All specifications are subject to change without notice. “JL Audio®”and “How we play®” are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo are trademarks
of JL Audio, Inc.
Printed in USA • ©2017 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
www.jlaudio.com
JLA-SKU# 011502 • ver. 12.05.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
®
Dieses Handbuch passt für folgende Modelle
1
Andere JL Audio Subwoofer Handbücher
JL Audio
JL Audio 6W3v3-4 Bedienungsanleitung
JL Audio
JL Audio Fathom IWS-SYS-2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-T-4RNR2/10W3v2 Bedienungsanleitung
JL Audio
JL Audio 6W0-4 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-GM-CAM12W6v2 Bedienungsanleitung
JL Audio
JL Audio 15W3v2-D2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-N-370/10W3v3 Bedienungsanleitung
JL Audio
JL Audio 13TW5v2-2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-GM-BURB/10W3 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-POL-SLINGSUBD/10W3v3-4 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-GM-BURBCNSL/10W3v2 Bedienungsanleitung
JL Audio
JL Audio 15W5 Speci?cations Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-GM-ESC/10W1v2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-H-CIVSDN/10W6v2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-B-X5/10W1v2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-N-PTHFNDR/10W Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-N-MURAN/10W1v2 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-M-3-SPD/10W3v3 Bedienungsanleitung
JL Audio
JL Audio 15W3v2-D4 Bedienungsanleitung
JL Audio
JL Audio Stealthbox SB-GM-HUMRH2/12W6v2 Bedienungsanleitung
