JLG 1932E3 Bedienungsanleitung

October, 2012

E3 Scissor Platform

Control Measures

2.6.5 Duplicate controls: Location, accessibility, protection and selection

Duplicate controls for all powered functions that are necessary to retrieve the platform in an emergency shall be provided at the

base or ground level, and shall override control devices situated on the work platform.

Extracts from ASNZS 1418-10 2011

2.6.4 Work platform controls: Location, accessibility, protection

Control devices shall be situated on the work platform and shall be readily accessible to the operator. Platform control boxes not permanently

attached shall have their normal location and orientation clearly marked on the platform and the control box.

When released, all control devices shall automatically return to the ‘off’ or ‘neutral’ position, if used to control any movement of the MEWP.

All control devices shall be protected against activation other than that initiated by the operator.

NOTE: A separate control, which has to be continuously activated by the operator in order for any motion to take place, meets this

requirement.

Where a separate control is integral with a motion control, the control shall be mechanically protected against inadvertent actuation.

A guard shall be provided and located at least 50 mm above the highest point of the controls.

2.6.10 Overriding emergency system

Overriding of the platform emergency stop control and load-sensing system is allowed for rescuing a trapped or incapacitated operator on the

platform. Overriding is permitted only by the use of a safety device that is independent from the selection control device. The safety device shall be

operated by hold to run controls.

The overriding of the load-sensing system shall allow motion of the platform sufficient to rescue the operator. Features shall be provided to protect

against misuse of the overriding system.

Refer to the JLG operating manual for the Scissorlift .

Download operators manuals from:

www.jlg.com.au >Product Manuals>JLG > JLG Scissorlifts>

Control measure

1530E3

1932E3

2033E3

2046E3

2646E3

2658E3

Platform Emergency Stop switch, RED

Yes

Mechanical guarding at controls

Yes

Controls >50mm below the guard rails

Yes

Trigger switch as enable switch

Yes

Inactivity Timer on trigger switch

Yes, 3 seconds

Interlock to prevent operation if joystick or switch

activated before release of RED emergency stop switch

Yes

Proportional lift

Yes

Proportional drive

Yes

Start-up system test’.

Yes

Lift /drive Function selector switch, momentary or

maintained.

Momentary

3 sec timeout

Momentary

3 sec timeout

Momentary

3 sec timeout

Momentary

3 sec timeout

Momentary

3 sec timeout

Momentary

3 sec timeout

Outdoor use Permitted

Yes, 1 person

Yes 1 person

Yes, 1 person

Yes, 2 person

Yes 2 person

Level sensor

Yes, 1.5 x 1.5 stowed

Yes, 2 x 2 stowed

Out of Level Sensor cutout

Lift and elevated drive

Lift and elevated

drive

Lift and elevated

drive

Lift and elevated

drive

Side slope level sensor setting at full elevation

1.5 degree

2 degree

Pothole protection system

Prevents elevated

drive only

Prevents elevated

drive only

Prevents elevated

drive only

Prevents elevated

drive only

Prevents elevated

drive only

Prevents elevated

drive only

Ground controls override the platform controls in

emergency

Yes.

Yes

Manual bleed down valve at base

Yes, pull cable

Motion Alarm

Yes

Strobe light at base

Yes

JLG E3 Series Scissor lift 1532E3,1932E3, 2033E3, 2046E3, 2646E3, 2658E3

Mechanical protection:

Joystick controller protected by external

metal guard over the control box.

Platform control Box mounted on front

rail.

Control System:

Red Emergency switch shuts down all

platform functions.

Drive and lift momentary selector switch

allows either drive or lift. Operator to

select. Times out after 3 seconds.

Joystick activation without the trigger

switch will prevent movement.

Trigger switch times out after 3 second

inactivity to prevent misuse.

Joystick proportional function requires

trigger switch to be activated before

moving joystick.

JLG E3 Scissor with Proportional

platform control system and

mechanical guarding.

JLG SMART System Multiplex Control Unit.

•E3 Scissor all sizes scissors function, and 3246E2 with Proportional motor control

•The JLG designed SMART System™ is a 24 Volt multiplex motor control unit installed on the electric scissor lift models 1532E3, 1932E3, 2033E3,

2046E3, 2646E3 and 2658E3.

•Emergency Stop Switch - A two-position, red, mushroom-shaped emergency stop switch functions to provide power to the platform control station

and also to turn off power to the platform function controls in the event of an emergency. With the power selector switch positioned to platform,

power is turned on by pulling the switch out (on), and is turned off by pushing the switch in (off). Turning the emergency stop switch off and then on

again will reset the smart system if a system fault has occurred and the machine has shut down.

•Lift Switch - The lift switch, when used in conjunction with the joystick, provides for raising and lowering the platform. Lift is activated by pressing

the lift switch and moving the joystick forward (lift up) or backward (lift down). Lift up speed is determined by the distance the joystick is moved

forward. Lift down speed is non-adjustable, and lift down is attained by moving the joystick fully backward. The lift switch is part of the enable circuit,

which provides power to the joystick and the lift function for 3 seconds when the lift switch is pressed. If the joystick is not activated within 3

seconds, the lift switch must be pressed again before activating the joystick. When the joystick is returned to the center off position, the operator

has 3 seconds to re-activate the joystick or select another function before power is removed by the enable circuit. Do not try to operate the drive,

lift, and powered deck extension functions simultaneously. If the drive, lift, and powered deck extension functions are selected simultaneously, no

function will operate. If this occurs, pause, then press only one of the function switches to activate the function.

•Drive Switch - The drive switch, when used in conjunction with the joystick, provides for driving the machine in forward or reverse. Drive is activated

by pressing the drive switch, in conjunction with the trigger switch, and moving the joystick forward (forward) or backward (reverse). Drive speed is

determined by the distance the joystick is moved forward or backward. Increased drive speed is possible when the high drive speed switch is pressed

either simultaneously with the drive switch or while operating the drive function. The drive switch is part of the enable circuit, which provides power

to the joystick and the drive function for 3 seconds when the drive switch is pressed. If the joystick is not activated within 3 seconds, the drive

switch must be pressed again before activating the joystick. When the joystick is returned to the center off position, the operator has 3 seconds to

re-activate the joystick or select another function before power is removed by the enable circuit. In addition, the posi-trac switch can be engaged

while operating the drive function to give a more evenly distributed oil flow to each drive motor.

Dieses Handbuch passt für folgende Modelle

Andere JLG Hubarbeitsbühne Handbücher

JLG

JLG 100SX Bedienungsanleitung

JLG

JLG E450AJ Gebrauchs- und Pflegehandbuch

JLG

JLG 600SJ Installations- und Benutzerhandbuch

JLG

JLG TOUCAN 1010 I Gebrauchs- und Pflegehandbuch

JLG

JLG T500J Gebrauchs- und Pflegehandbuch

JLG

JLG R4045 Gebrauchs- und Pflegehandbuch

JLG

JLG X17JPLUS Gebrauchsanweisung

JLG

JLG E300A Gebrauchs- und Pflegehandbuch

JLG

JLG Lull 1044C-54 II Series Bedienungsanleitung

JLG

JLG 80SL Bedienungsanleitung

JLG

JLG 330CRT Gebrauchs- und Pflegehandbuch

JLG

JLG 340AJ Installations- und Benutzerhandbuch

JLG

JLG 800S Gebrauchs- und Pflegehandbuch

JLG

JLG X390AJ-X14J Betriebsanleitung

JLG

JLG 600S Gebrauchs- und Pflegehandbuch

JLG

JLG 800AJ HC3 Gebrauchs- und Pflegehandbuch

JLG

JLG 15MVL Series Bedienungsanleitung

JLG

JLG GRADALL 544D-10 Gebrauchs- und Pflegehandbuch

JLG

JLG H340AJ Gebrauchs- und Pflegehandbuch

JLG

JLG RT3394 Gebrauchs- und Pflegehandbuch

JLG

JLG 450A II Series Gebrauchs- und Pflegehandbuch

JLG

JLG 1850SJ Installations- und Benutzerhandbuch

JLG

JLG 800A Gebrauchs- und Pflegehandbuch

JLG

JLG Skytrak 6036 Gebrauchs- und Pflegehandbuch

Beliebte Hubarbeitsbühne Handbücher anderer Marken

Genie

Genie Z-80 Bedienungsanleitung

Genie

Genie Z-45/25 Bedienungsanleitung

Terex

Terex Z80H-7733 Bedienungsanleitung

Terex

Terex Gyro 4020 Bedienungsanleitung

Terex

Terex Genie Z-51/30 J Bedienungsanleitung

LGMG

LGMG T65JE Bedienungsanleitung

Genie

Genie Z-135/70 Bedienungsanleitung

Oshkosh Corporation

Oshkosh Corporation JLG H800AJ Gebrauchs- und Pflegehandbuch

Oshkosh

Oshkosh JLG 1500SJ Installations- und Benutzerhandbuch

Skyjack

Skyjack SJ30AJE Bedienungsanleitung

Oshkosh

Oshkosh JLG 800A Installations- und Benutzerhandbuch

Terex

Terex Genie Z-135/70 Bedienungsanleitung

Skyjack

Skyjack SJ 46AJ Bedienungsanleitung

Molift

Molift Quick Raiser 205 Bedienungsanleitung

Snorkel

Snorkel SL26RTE Kurzanleitung

Terex

Terex Genie Z-135/70 Installations- und Betriebsanleitung

Terex

Terex Genie ZX-135/70 Installations- und Betriebsanleitung

Oshkosh Corporation

Oshkosh Corporation JLG E300A Bedienungsanleitung