JLG TH336 Bedienungsanleitung

Page 1 of 4

February 16, 2011

ATTENTION: This notice is being issued to advise you of the requirement to update certain

Caterpillar (“CAT”) Telehandlers that were manufactured by JLG Industries,

Inc. (“JLG”). This program must be completed as soon as possible on all

affected machines.

PROBLEM:

When the fork tilt up function is continuously held and the tilt cylinder reaches end of stroke and

then the lift up function is activated while continuing to activate fork tilt up, a void in the barrel

end of the lift cylinder is created. As a result of this void, when lift up or down is initiated, the

boom will drop in an uncontrolled manner until the void is filled with hydraulic oil.

In has recently been determined that the load charts on certain CAT Model TH336, TH337,

TH406 and TH407 telehandlers do not have the correct load values. Lifting certain loads

specified on those load charts will cause the machine to tip-over.

This bulletin requires the installation of a compensating valve kit in order to eliminate the

possibility of a void being created in the lift cylinder or the replacement of the load charts or both

on all affected machines.

AFFECTED PRODUCTS:

This issue affects certain CAT Telescopic Material Handler Models TH336, TH337, TH406 and

TH407 having the following Serial Numbers.

Model Affected Serial Number(s)

GROUP A

Load Chart Book Replacement & Compensating Valve Kit Installation Procedure

TH336 TDE00102, 104-116, 118-134, 136, 138-139, 141, 143, 145-147, 149-

150, 152-154, 157.

TH337 TDF00101-103, 105-184, 186, 189-193, 195, 198.

SERVICE LETTER

Reference:

SAFETY PRODUCT IMPROVEMENT PROGRAM FOR THE INSTALL

TION

OF A HYDRAULIC COMPENSATING VALVE OR LOAD CHART

REPLACEMENT OR BOTH ON CERTAIN CAT MODEL TH336,

TH337, TH406 AND TH407 TELEHANDLERS.

#C111C3

Page 2 of 4

TH406

TBX00102-105, 107, 114, 119, 121, 123-126, 128-129, 131-136, 145-

149, 151, 154, 158, 161, 163-168, 171-175, 177-199, 201-205, 207-208,

210, 212, 215, 217, 219-221, 223-224, 228, 237, 240-241, 244-254, 257,

259, 263, 265, 271-272, 275, 277-278, 280-282, 285-286, 289-290, 295,

299-300, 302-307, 312-330.

TH407

TBY00101, 103, 105-109, 111-114, 116-174, 177-200, 202-224, 232-262,

265-268, 270-280, 283-287, 290-299, 301-305, 307-324, 326-328, 331,

333-336, 338-343, 345-346, 348-359, 361-362, 364-383, 385, 388, 390,

391-392, 394, 396-402, 404-408, 410-413, 415, 417-418, 421-423, 425-

431, 433-437, 439-442, 444-445, 447, 449-452, 454, 456-461, 463-467,

469-471, 473-480, 482-484, 486-488, 490-491, 493, 495-498, 500-504,

516-524, 526-527, 530-534, 537-538, 540-547, 550-551, 554-557, 560-

561, 566-573, 575-582, 584-587, 589-592, 594-600, 602-603, 605-606,

608-615, 617-632, 635, 637, 639, 641, 644, 653.

Model Affected Serial Number(s)

GROUP B

Compensating Valve Kit Installation Procedure

TH336 TDE00101, 103, 117, 137, 140, 142, 148, 155, 158, 160, 162-169, 171-

173, 175-187.

TH337 TDF00199, 201, 204-212.

TH406 TBX00118, 169, 331-332, 336-341, 343-349.

TH407 TBY00115, 525, 529, 558-559, 562-565, 574, 583, 616, 633-634, 636,

647, 649, 651-652, 654-664, 666, 668-738, 741, 746-747.

PARTS NEEDED:

Reference the above affected Serial Numbers Groups. Each Group will require the

accomplishment of a different procedure and the appropriate kits must be ordered for each

affected unit. The following parts must be ordered to accomplish this update:

For GROUP A UNITS Only:

Model Quantity Part Number Description

1 361-4174 Compensating Valve Kit

TH336 1 337-5091 Load Chart Kit

1 361-4175 Compensating Valve Kit

TH337 1 337-5092 Load Chart Kit

1 361-4174 Compensating Valve Kit

TH406 1 332-9697 Load Chart Kit

#C111C3

Page 3 of 4

1 361-4175 Compensating Valve Kit

TH407

1 326-1977 Load Chart Kit

For GROUP B UNITS Only:

Model Quantity Part Number Description

TH336 & TH406 1 361-4174 Compensating Valve Kit

TH337 & TH407 1 361-4175 Compensating Valve Kit

ACTION REQUIRED:

GROUP A UNITS

Remove the existing load chart book located in the cab and replace with the revised

load chart. Destroy and discard the original load chart booklet.

The Compensating Valve Kit must be installed on all affected units in accordance

with the enclosed Compensating Valve Kit Installation Procedure.

GROUP B UNITS

The Compensating Valve Kit must be installed on all affected units in accordance

with the enclosed Compensating Valve Kit Installation Procedure.

SERVICE CLAIM ALLOWANCES:

To receive reimbursement, file a service claim through the normal CAT service claims process.

When filing this claim through the CAT system, please use the following codes in the

appropriate input fields: Input Field Before Failure

Part Causing Failure C111C3

Group Number 5086

Warranty Claim Description 56

SIMS Description Code T

#C111C3

Page 4 of 4

The reimbursement terms of this program are as follows:

Caterpillar Dealer Suggested Customer Suggested

Parts % Labor Hrs % Parts % Labor Hrs % Parts % Labor Hrs %

100% 100% 0% 0% 0% 0%

Labor Time:

Compensating Valve installation is a 1.5 hour job.

Load Chart installation is a 0.5 hour job.

Up to 2 hours and 100 km for travel.

PARTS DISPOSITION:

Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

CONTACTS:

A copy of this Service Letter will be available on the CAT Alliance Group website. If you have

any questions or need further information, please contact CAT Alliance Product Support.

Enclosures:

Compensating Valve Kit Installation Procedure

#C111C3

Page 1 of 7

PROCEDURE: Hydraulic Compensating Valve Installation

MODEL: CAT TH336, TH337, TH406 and TH407 Telehandlers

Kits Parts Breakdown:

• Telehandler Model TH336 & TH406, Kit # 361-4174

P/N in Kit Qty in Kit Description

353-3455 1 Hydraulic Valve

298-0462 1 Hydraulic Straight Adapter

303-4754 3

Hydraulic 90 degree Adapter

353-3454 1 Bracket

297-7091 2 HexHead Bolt

8T-4224 4 Washer

5C-7261 2 Nut

343-7049 2 Hose Clamp

353-3448 1 Hose Assembly

353-3451 1 Hose Assembly

353-3450 1 Hose Assembly

353-3449 1 Hose Assembly

342-3862 3 Cable Tie

• Telehandler Model, TH337 & TH407, Kit # 361-4175

P/N in Kit Qty in Kit Description

353-3455 1 Hydraulic Valve

298-0462 1

Hydraulic Straight Adapter

303-4754 3

Hydraulic 90 degree Adapter

353-3454 1 Bracket

297-7091 2 HexHead Bolt

8T-4224 4 Washer

5C-7261 2 Nut

343-7049 2 Hose Clamp

353-3448 1 Hose Assembly

353-3451 1 Hose Assembly

353-3452 1 Hose Assembly

335-3453 1 Hose Assembly

353-3862 1 Cable Tie

#C111C3

Page 2 of 7

CAUTION: USE ALL APPLICABLE SAFETY PRECAUTIONS WHILE

WORKING ON, UNDER OR AROUND ANY MACHINERY.

IMPORTANT! THIS PROCEDURE MUST BE ACCOMPLISHED IN A

CONTAMINANT-FREE ENVIRONMENT. ENSURE THE AREA IS

FREE FROM DIRT AND DEBRIS BEFORE REMOVING ANY

HYDRAULIC COMPONENTS.

IN THE EVENT OF CONTAMINATION CLEAN THE HYDRAULIC

SYSTEM OIL UNTIL THE HYDRAULIC OIL CLEANLINESS FACTOR

MEETS ISO 18/15, NO ADDITIONAL TIME IS INCLUDED IN THIS

PROCEDURE FOR SYSTEM FLUSHING.

Procedure – Hydraulic Compensating Valve Installation:

1. Remove any attachment from the machine.

2. Prepare the machine for servicing by:

a. Park the machine on a firm, level surface with the machine level

b. Retract the boom and elevate the boom to approximately a 33 degree

boom angle.

c. Place the travel select lever in the (N) NEUTRAL position and engage the

parking brake.

d. Position the rod end of the tilt cylinder to the fully extended position.

e. Shut the engine OFF.

f. Properly support the boom.

g. Chock the front and rear wheels of the machine.

3. Remove the hydraulic valve from the kit (P/N 353-3455) and insert adapter (P/N

298-0462,) into the port marked “C2”. Torque the fitting to 55 Nm (41 lb ft).

4. Install the three 90º elbow adapters (P/N 303-4754) into the three remaining

ports of the valve. Torque the fittings to 55 Nm (41lb ft), ensuring the orientation

is as shown in Figure #1.

#C111C3

Page 3 of 7

5. Apply loctite #243 to the threads of both hex head bolts (P/N 297-7091).

6. Attach hydraulic valve (P/N 353-3455) to the mounting bracket (P/N 353-3454)

as shown in Figure #2, using the two hexhead bolts (P/N 297-7091). A washer

(P/N 8T-4224) must be placed on both the head and nut end of the bolt. Secure

with nut (P/N 5C-7261).

FIGURE #2

7. Measure 570 mm (22-1/2 inches) from the compensation cylinder barrel rod end

and mark the location (refer to Figure #3).

FIGURE #1

Note: Left hand image shows ports marked “V1” and “V2”.

Right hand image shows ports marked “C1” and “C2”.

Secondary ports are uppermost in both images.

#C111C3

Page 4 of 7

FIGURE #3

8. Using clamps (P/N 343-7049) securely attach the valve and bracket assembly to

the compensation cylinder (Note: the bolts inserted in Step #7 should be on the

left hand side of the valve block when mounted).

9. The left hand side of the valve should be placed to correspond with the mark

made in Step #8. Tighten both clamps with a torque of 4.5 Nm (3.3 lb ft).

10. Remove and discard any cable ties fitted to the compensation cylinder hoses.

11. Prepare to loosen the compensation cylinder hydraulic hoses by placing a drain

pan of suitable size close to the work area. Oil discharge will be less than 1 litre

(1/4 gallon).

12. Carefully loosen the compensation cylinder hoses, attached to the hydraulic pipe

mounted on the underside of the boom, allowing any trapped pressure to relieve.

Allow oil to drain into a suitable receptacle then remove both hoses completely

from the cylinder, destroy or responsibly discard.

13. Install hose (P/N 353-3448) from the rod end of the compensation cylinder to

valve port marked “V1”. Correctly torque the hose fitting to 55 Nm (41lb ft).

14. Re-orientate the fitting located at the non-rod end of the compensation cylinder

(refer to Figure #4). Install hose (P/N 353-3451) from valve port marked “V2” to

this fitting. Correctly torque the hose fitting to 55 Nm (41 lb ft).

#C111C3

Page 5 of 7

FIGURE #4

15. Install hoses as follows:

a. (TH336 and TH406 only)

Using hose (P/N 353-3450) connect valve port marked “C1” to the inner

boom hydraulic pipe and hose (P/N 353-3449) from the outer boom

hydraulic pipe to valve port marked “C2”. Correctly torque the hose fittings

to 55 Nm (41 lb ft).

b. (TH337 and TH407 only)

Using hose (P/N 353-3453) connect valve port marked “C1” to the inner

boom hydraulic pipe and hose (P/N 353-3452) from the outer boom

hydraulic pipe to valve port marked “C2”. Correctly torque the hose fittings

to 55 Nm (41 lb ft).

16. Ensure the outer face corners of the hydraulic valve block are spaced the same

distance from the boom. If necessary adjust positioning of the valve until correct

position is achieved. Ensure the clamps installed in Step #8 are secure.

17. Using four cable ties (three on TH337 and TH407) fix both boom hoses to the

boom hydraulic pipe as shown in Figure #5.

#C111C3

Page 6 of 7

FIGURE #5

18. Confirm installation is correct as shown in Figure #6.

FIGURE #6

#C111C3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JLG Hebesystem Handbücher

JLG

JLG 1230ES Gebrauchs- und Pflegehandbuch

JLG

JLG 1350SJP Gebrauchs- und Pflegehandbuch

JLG

JLG 600SC Gebrauchs- und Pflegehandbuch

JLG

JLG 800A Gebrauchs- und Pflegehandbuch

JLG

JLG E600 Installations- und Benutzerhandbuch

JLG

JLG 260MRT Gebrauchs- und Pflegehandbuch

JLG

JLG LiftPod FT70 Installations- und Benutzerhandbuch

JLG

JLG 25RTS Installations- und Benutzerhandbuch

JLG

JLG 600SJ Installations- und Benutzerhandbuch

JLG

JLG LiftPod FS60 Installations- und Benutzerhandbuch

JLG

JLG 1930ES Gebrauchs- und Pflegehandbuch

JLG

JLG 450A Installations- und Benutzerhandbuch

JLG

JLG 600A Gebrauchs- und Pflegehandbuch

JLG

JLG EcoLift50 Installations- und Benutzerhandbuch

JLG

JLG Toucan 12E Gebrauchs- und Pflegehandbuch

JLG

JLG 10msp Gebrauchs- und Pflegehandbuch

JLG

JLG 260MRT Bedienungsanleitung

JLG

JLG 400S Installations- und Benutzerhandbuch

JLG

JLG RT2669 Installations- und Benutzerhandbuch

JLG

JLG 25AM Gebrauchs- und Pflegehandbuch

JLG

JLG 740AJ Installations- und Benutzerhandbuch

JLG

JLG Toucan 12E Installations- und Benutzerhandbuch

JLG

JLG 600A Gebrauchs- und Pflegehandbuch

JLG

JLG 600AJ Installations- und Benutzerhandbuch

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung