JobSmart 1363310 Bedienungsanleitung
Instruction Manual
REV 02/25/19
Steel Hand Crank Hose Reel
WARNING:
Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety
rules and other basic safety precautions may result in serious personal injury.
Save these instructions in a safe place and on hand so that they can be read when required.
Keep these instructions to assist in future servicing.
GENERAL SAFETY REGULATIONS
WARNING: The warnings, cautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions or situations that could occur. It
must be understood by the operator that common
sense and caution are factors that cannot be built into
this product but must be supplied by the operator.
1. Keep the work area clean and dry. Damp or wet work areas can result in
injury.
2. Keep children away from work area. Do not allow children to handle this
product.
3. Use the right tool for the job. Do not attempt to force small equipment to do
the work of larger industrial equipment. There are certain applications for
which this equipment was designed. It will do the job better and more safely
at the capacity for which it was intended. Do not modify this equipment, and
do not use this equipment for a purpose for which it was not intended.
4. Check for damaged parts. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace damaged or worn parts immediately.
5. Do not over-reach. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etc.
6. DO NOT use the equipment when tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating this
equipment may result in serious personal injury.
TECHNICAL DETAILS
SAFETY PRECAUTIONS
1. Make sure incoming pressure does not exceed the rated pressure.
2. Use the proper eye protection when assembling and using the hose reel.
3. Assemble the hose reel on a clean workbench free of debris and moisture.
4. Use liquid soap when checking for air leakage.
5. Keep children away from the work area.
WARNING: Exposure of skin directly to pressurized air, or fluid could result in severe
bodily injury.
INSTALLATION AND ASSEMBLY
Note: You will need to purchase appropriate hardware for mounting your new reel.
Refer to appendix for assembly.
Put the lead hose onto the swivel, then screw down the lead hose fitting onto the swivel to
tighten the lead hose. Feed the long hose through the drum opening, then wrap the hose on
the drum.
REPLACEMENT OF SWIVEL SEAL
1. Turn off and disconnect supply line from swivel inlet.
2. Remove swivel assembly from reel axle.
3. Remove circlip from swivel, and take apart. Note: You may want to remove swivel from reel
hose end, but this is not necessary unless a new swivel is being installed.
4. Replace the seals and reassemble swivel.
5. Use Teflon type or thread sealant on swivel thread fitting, reconnect the swivel thread fitting
with axle.
6. Re-connect inlet supply line.
REPLACEMENT OF HOSE
1. Turn off supply to reel.
2. Pull out all the old hose and lock the reel in this position.
Caution: Make sure reel drum is securely locked and cannot rotate back.
3. Remove two hose clamps from hose.
Item No.
1363310 Flexible Hybrid Polymer 3/8”(9.50mm)
Max Pressure Hose Capacity
Material I.D. Length
75ft/22.80m
Inlet/Outlet
1/4"
300Psi (20Bar)
E1
TECHNICAL
DETAILS
SAFETY
PRECAUTIONS
LIMITED
WARRANTY
EXPLODED AND
PARTS LIST
INSTALLATION AND
ASSEMBLY
10.24"/260mm
14.22"/361.2mm
13.33"/338.5mm
12.99"/330mm
4. Carefully disconnect hose from swivel joint on side of reel, or male fitting in axle center and
remove old hose.
5. Feed new hose through guide and opening in drum, and connect to swivel. Re-install two
hose clamps, on inside and outside of drum flange.
6. Carefully release the drum latch, and slowly allow the hose to wind onto the reel.
LIMITED WARRANTY
1. The manufacturer warrantees this hose reel against defects in material and craftsmanship
for a period of 12 months from date of purchase.
2. Hose, if supplied with reel, and O-rings are deemed to be normal wear items; not warranted.
3. Manufacturer’s liability is limited to replacement or repair of defective material within the
warranty period, when returned freight prepaid to the distributor or their designated service
depot.
4. The warranty does not cover damage caused by accident or misuse or faulty installation.
5. The reel must be installed and maintained in compliance with these instructions.
EXPLODED AND PARTS LIST
E2
TECHNICAL
DETAILS
SAFETY
PRECAUTIONS
LIMITED
WARRANTY
EXPLODED AND
PARTS LIST
INSTALLATION AND
ASSEMBLY
Size: 145x210mm REV 02/25/19157克铜版纸
Part No.
1
2
3
4
5
6
7
8
9
10
11
Description
Frame
Swivel Assembly
Lead-in Hose Assembly
Plastic Handle
E-ring
L-shape Handle
Nut
Hose Cramp
Plastic Base
Support Axle Assembly
Spring
Q’ty
1
1
1
1
1
1
3
1
1
1
1
Part No.
12
13
14
15
16
17
18
19
20
21
Description
Washer
Screw
Washer
Bolt
Flange
Hose Assembly
Screw
Bearing Assembly
Reel-core Assembly
Nut
Q’ty
1
4
10
1
2
1
10
2
2
1
13
2
3
19
18
20
17 816 21
1 15 7 129
11
10
6
5
4
14
Inhaltsverzeichnis
Andere JobSmart Werkzeuge Handbücher
