John Lewis JL110 Bedienungsanleitung

JL110 / JL110SE

Instruction book

IMPORTANT SAFETY INSTRUCTIONS

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with this sewing machine.

When using an electrical appliance, basic safety precautions should always be followed, including the

following:

This sewing machine is designed and manufactured for household use only.

Read all instructions before using this sewing machine.

DANGER— To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this sewing

machine from the electric outlet immediately after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 15

Watts.

WARNING—To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used

by or near children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if

it has been dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealer or service center for examination,

repair, electrical or mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this

sewing machine and foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine

needle and/or cutting blade.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as

threading the needle, changing the needle, threading the bobbin or changing the presser foot, and

the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or

when making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

The design and specifications are subject to change without a prior notice.

Please note that on disposal, this product must be safely recycled in accordance with relevant National

legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance.

(European Union only)

INDICE

SECTION 1. ESSENTIAL PARTS

Name of Parts ................................................................................................................. 2

SECTION 2. GETTING READY TO SEW

Extension Table ............................................................................................................... 3

Standard Accessories ..................................................................................................... 3

Accessories Storage Box ................................................................................................ 3

Connecting the Machine to the Power Supply ................................................................ 4

Foot Control ....................................................................................................................4

Presser Foot Lifter ........................................................................................................... 5

To Attach and Remove the Presser Foot ........................................................................ 5

Changing Needle ............................................................................................................ 6

Thread and Needle Chart ............................................................................................... 6

Setting Spool Pins ........................................................................................................... 7

Removing or Inserting the Bobbin Case ......................................................................... 7

Winding the Bobbin ......................................................................................................... 8

Threading Bobbin Case .................................................................................................. 8

Threading the Machine ................................................................................................... 9

Drawing Up Bobbin Thread ........................................................................................... 10

Balancing Needle Thread Tension ................................................................................ 11

Pattern Selector Dial ..................................................................................................... 12

Stitch Length Dial .......................................................................................................... 13

Reverse Stitch Button ................................................................................................... 14

Darning Plate ................................................................................................................ 14

SECTION 3. BASIC SEWING

Straight Stitch Sewing ................................................................................................... 15

To change the direction ................................................................................................. 15

Seam Guide Line .......................................................................................................... 16

Turn a Square Corner ................................................................................................... 16

Zigzag Stitching ............................................................................................................ 17

Tricot Stitch ...................................................................................................................18

Overedge Stitching........................................................................................................ 18

Triple Stitch ...................................................................................................................19

Sewing Buttons ............................................................................................................. 20

Buttonhole ..................................................................................................................... 21

Blind Hem Stitch ........................................................................................................... 22

SECTION 4. DECORATIVE STITCHES

Shell Tuck ...................................................................................................................... 23

Stretch Stitch Patterns .................................................................................................. 23

Smocking ...................................................................................................................... 24

Applique ........................................................................................................................24

SECTION 5. CARE OF YOUR MACHINE

Dismantling and Assembling ......................................................................................... 25

Shuttle Race Unit .......................................................................................................... 25

Cleaning the Feed Dog ................................................................................................. 25

Sewing Light.................................................................................................................. 26

Trougleshooting ............................................................................................................. 27

@0 @1

SECTION 1. ESSENTIAL PARTS

Name of Parts

qReverse stitch button

wPattern selector dial

eStitch length dial

rBobbin winder stopper

tBobbin winder spindle

ySpool pins

uBobbin winder thread guide

iThread guide

oThread take-up lever

!0 Thread tension dial

!1 Face plate

!2 Needle plate

!3 Extension table

!4 Presser foot holder

!5 Needle clamp screw

!6 Needle

!7 Presser foot

!8 Carrying handle

!9 Balance wheel

@0 Power switch

@1 Machine socket

@2 Free arm

@3 Presser foot lifter

Note: The specifications are subject to change

without prior notice.

Extension Table

The extension table provides added sewing

surface and can be easily removed for free arm

sewing.

Detaching the table:

Pull the table away from the machine.

Attaching the table:

Push the extension table until it snaps into the

machine.

SECTION 2. GETTING READY TO SEW

Standard Accessories

qBobbins

wSeam ripper/ Buttonhole opener

eNeedle set

rButtonhole foot

tDarning plate

yZigzag foot

Accessories Storage Box

Sewing accessories are conveniently located in the

extension table.

qAccessories storage box

• Advantages and uses of free arm sewing:

– Avoid fabric bunching around the needle when

bartacking to reinforce pockets, plackets and

waistlines.

– For stitching sleeves, waistbands, pant legs or

any circular garment area

– For darning socks or mending knees, elbows

or areas of wear in children's clothes

Connecting the Machine to the Power Supply

Before connecting the power cord, make sure the

voltage and frequency shown on the machine

conform to your electrical power.

1. Turn off the power switch.

2. Insert the machine plug into the machine

socket.

3. Insert the power supply plug into the outlet .

4. Turn on the power switch to turn on the power

and sewing light.

Sewing speed can be varied by the foot control.

The harder you press on the control, the faster the

machine runs.

Caution:

Do not place anything on the foot contorol,

otherwise the machine will start advertently.

Foot Control

qPower switch

wOutlet

eMachine socket

rMachine plug

tFoot control

yPower supply plug

WARNING:

While in operation, always keep your eyes on the

sewing area, and do not touch any moving parts such

as the thrad take-up lever, handwheel or needle.

Always turn off the power switch and unplug from the

power supply:

– when leaving the machine unattended.

– when attaching or removing parts.

– when clearning the machine.

Do not place anything on the foot control, otherwise the

machine will run intermittently.

Presser Foot Lifter

The presser foot lifter raises and lowers your presser

foot.

You can raise it about 0.6 cm (1/4˝) higher than the

normal up position for easy removal of the presser

foot or to help you to place heavy fabric under the foot.

qNormal up position

wHighest position

CAUTION:

Turn off the power switch when changing a presser foot.

To Attach and Remove the Presser Foot

To remove

Turn the handwheel toward you to raise the needle to its

highest position.

Raise the presser foot.

Press the lever on the back of the foot holder.

The presser foot will drop off.

To attach

Place the presser foot so the pin on the foot lies just

under the groove of the foot holder.

Lower the foot holder to lock the foot in place.

qPin

wGroove

Changing Needle

CAUTION:

Turn off the power switch when changing a needle.

Raise the needle by turning the handwheel toward you

and lower the presser foot.

Loosen the needle clamp screw by turning it counter-

clockwise.

Remove the needle from the clamp.

Insert the new needle into the clamp with the flat side

away from you.

When inserting the needle into the clamp, push it up as

far as it will go and tighten the clamp screw firmly with the

screwdriver.

* Check your needles frequently for barbed or

blunted points. Snags and runs in knits, fine silks and

silk-like fabrics are permanent and are almost always

caused by a damaged needle.

Place the flat side of the needle on something flat (needle

plate, glass etc.). The clearance between the needle and

flat surface should be consistent. Never use a bent or blunt

needle.

To check the needle

Thread and Needle Chart

Fabrics Thread

Needle Size

Crepe de Chine,

Voile,Lawn, Organdy,

Georgette,

Tricot

Light

weight

Medium

weight

Heavy

weight

Linens, Cotton. Pique,

Serge, Double Knits,

Percale

Denim, Tweed,

Gabardine, Coating,

Drapery and

Uphollstery Fabric

Fine Silk

Fine Cotton

Fine Synthetic

Fine Cotton

Covered

Polyester

50 silk

50 to 80 Cotton

50 to 60

Synthetic

Cotton Coverd

Polyester

50 silk

40 to 50 Cotton

40 to 50

Synthetic

Cotton Coverd

Polyester

When inserting the bobbin case, place the horn into the

recess of the hook race.

e Horn

The spool pins are used for holding the spool of thread in

order to feed thread to the machine.

To use, pull up the spool pin. Push down for storage.

Setting Spool Pins

Removing or Inserting the Bobbin Case

Open the hook cover.

q Hook cover

Raise the needle by turning the handwheel toward you.

Take out the bobbin case by holding the latch.

w Latch

Winding the Bobbin

1 Pull the handwheel out.

2 Draw the thread from spool.

Guide the thread around the bobbin winder thread guide.

3 Insert the thread through the hole in the bobbin from

the inside to the outside.

Align the notch qof bobbin to the bobbin winder

spindle rib w.

Put the bobbin on the bobbin winder spindle.

Note: Return the bobbin winder spindle when the

machine stops.

4 Push it to the right.

5 With the free end of the thread held in your hand,

depress the foot control.

Stop the machine when it has made a few turns, and

cut the thread close to the hole in the bobbin.

6 Depress the foot control again.

When the bobbin is fully wound, stop the machine.

Return the bobbin winder spindle to its original position

by moving the spindle to the left, and cut the thread.

7 Push the handwheel to the left. (original position).

Threading Bobbin Case

1 Place the bobbin into the bobbin case.

Make sure the thread unwinds in the direction of

arrow.

2 Pull the thread into the bobbin case slot.

3 Draw the thread under the tension spring and into

the delivery eye.

* Leave about 10 cm (4˝) of free thread.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere John Lewis Nähmaschine Handbücher

John Lewis

John Lewis JL 300 Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Singer

Singer 2517 Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Janome

Janome Quilt Maker Pro 18 VERSA Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung