Johnson Controls System 350 Y350R Service-Handbuch

FANs 930, 930.5, 125

Product/Technical Bulletin Y350R

Issue Date 0598

Part No. 24-7664-214, Rev. D

Code No. LIT-930090

The Y350R is a rectified Class 2, 24 VAC power

supply module designed specifically for use with

System 350™ Modular Control Systems.

As with all System 350 products, the Y350R is housed

in a compact NEMA 1, high-impact plastic enclosure.

The modular design provides easy, plug-in

connections for quick installation and future

expandability.

Figure 1: Y350R Power Module

System 350Y350R Power Module

Features and Benefits

❑Modular Design Enables stage, display, and power modules to be

purchased and installed as necessary

❑Plug-in Connectors and

35 mm DIN Rail Mounting Eliminates wiring between modules and reduces

installation costs

❑Accepts Input Voltages of

120 or 240 VAC, 50/60 Hz Reduces inventory by encompassing the primary

voltage requirements

2 Y350R Power Module Product/Technical Bulletin

pplication

The Y350R Power Module provides the power

necessary to operate all System 350 controls and

add-on modules. For system capabilities, see Table 1.

Table 1: Maximum Number of Add-on

Modules when Powered by a Y350R

Control

Module Stage Module Display

Module

A350A

A350B

A350E

9 S350A’s or S350C’s

6 S350A’s or S350C’s with

1 S350P

4 S350A’s or S350C’s with

2 S350P’s

1 D350

A350P 4 S350A’s or S350C’s

2 S350A’s or S350C’s with

1 S350P

1 D350

A350R

A350S 9 S350A’s or S350C’s

6 S350A’s or S350C’s with

1 S350P

4 S350A’s or S350C’s with

2 S350P’s

2 D350

W351A 5 S351’s 1 D351

W351P 4 S351’s 1 D351

P352A 5 S352’s 1 D352

P352P No additional stages available 1 D352

R353 5 S353’s No

display

available

All System 350 add-on modules snap on to a DIN rail

and plug into the control and to each other via 5-pin

connectors. Add-on modules can be arranged in any

order and there is no wiring required to interconnect

the System 350 components.

peration

The Y350R operates from 240 VAC or 120 VAC

power. A 24 VAC, Class 2, step-down transformer

brings the voltage to a level which the System 350

modules will accept. There are no adjustments for the

power module.

IMPORTANT: All Series Y350R Power Modules

are designed for use only in

conjunction with operating

controls. Where an operating

control failure would result in

personal injury and/or loss of

property, it is the responsibility of

the installer to add devices

(safety, limit controls) that protect

against, or systems (alarm,

supervisory systems) that warn

of, control failure.

imensions

Mounting Slot (4)

for No. 6 Screws

Y350

Conduit

Hole

0.145

3.68

2.94

DIN Rail

Mount 2.40

1.20

0.85

21.6

0.42

1.56

0.5

5.00

127

2.40

0.875

Figure 2: Y350R Dimensions, mm/in.

nstallation and Wiring

The Y350R case has provisions for mounting to a

standard 35 mm DIN rail, or can be mounted using the

four key slot mounting holes located in the rear of the

case.

Mount System 350 modules in any convenient location

using either the DIN rail mounts or the mounting holes

located on the back of the control case. The

components are not position sensitive, but should be

mounted so they can be easily wired and adjusted.

Y350R Power Module Product/Technical Bulletin 3

IMPORTANT: All wiring must be installed to

conform to the National Electrical

Code and local regulations.

1. Secure the module to the DIN rail, wall, or panel.

WARNING:Electrical Shock Hazard.

Disconnect power supply before

modules are interconnected and

wiring connections are made to

avoid possible electrical shock or

damage to the equipment.

2. Connect input wiring to the Y350R power module.

Strip approximately 3/8 inch from the wire

insulation, insert the wire under each terminal

screw, and tighten. (See Figure 3.)

Note: If conduit is used when installing System 350

components, be sure to connect the hub to the

conduit before the hub is secured to the

enclosure.

Module

Connector

Module

Connector

240 VAC COM 120 VAC

Power Input Terminals

Figure 3: Interior of the Y350R Power

Module

heckout Procedure

Before applying power, make sure installation and

wiring connections are according to job specifications.

After necessary adjustments and electrical

connections have been made, put the system in

operation and observe at least three complete

operating cycles before leaving the installation.

roubleshooting

If the control system does not function properly and

the Y350R is suspect, proceed as follows:

1. Connect a Digital Voltmeter (DVM) between the

24V (+) and COM (-) terminals located on the

control module’s left-side connector. (Terminal

designations are marked on the control module.)

2. Select DC volts on the DVM and verify that the

voltage is between 16 and 38 VDC. If the DVM

reading is within range, the Y350R is functioning

properly.

Note: Consult the

Troubleshooting

section of the

appropriate control bulletin for a complete

system troubleshooting procedure.

3. If the DVM reading is not within the indicated

voltage range, check wiring and correct if

necessary. If the wiring is correct and the reading

remains out of range, replace the Y350R.

epairs and Replacement

Field repairs or calibration must not be made.

Replacement modules are available through the

nearest Johnson Controls representative. (See Table

2.)

rdering Information

Table 2: Product Available

Item Product Code Description

Power Module Y350R-1C Rectified, Class 2, 24 VAC Power Supply

4 Y350R Power Module Product/Technical Bulletin

pecifications

Product Y350R Power Module

Input Voltage 120/240 VAC, 50/60 Hz

Output Voltage Rectified 24 VAC, 10 VA, Class 2

Material Case and cover: NEMA 1 high-impact plastic

Ambient Temperature Operating: -34 to 66°C (-30 to 150°F)

Shipping: -40 to 85°C (-40 to 185°F)

Ambient Humidity 0 to 95% RH non-condensing

Mounting Wall or DIN rail

Agency Listing UL Guide No. XAPX, File E27734

CUL Guide No. XAPX7, File E27734

CSA Class No. 4813 02, File LR948

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications,

consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.

Controls Group

507 E. Michigan Street

P.O. Box 423

Milwaukee, WI 53201 Printed in U.S.A.

Andere Johnson Controls Steuereinheit Handbücher

Johnson Controls

Johnson Controls Facility Explorer FX20 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco RV-1A Bedienungsanleitung

Johnson Controls

Johnson Controls TrueRH Series Leitfaden

Johnson Controls

Johnson Controls Tyco RSV-1 Bedienungsanleitung

Johnson Controls

Johnson Controls H Series Bedienungsanleitung

Johnson Controls

Johnson Controls VP1000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls MS-NCM4510-2 Bedienungsanleitung

Johnson Controls

Johnson Controls MS-IOM3723 Bedienungsanleitung

Johnson Controls

Johnson Controls C450CCN-2 Bedienungsanleitung

Johnson Controls

Johnson Controls A19 Series Bedienungsanleitung

Johnson Controls

Johnson Controls M300CJ Bedienungsanleitung

Johnson Controls

Johnson Controls S1-TTSCC Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco CV-300B Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco 8200-1466-01 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls FX-PCX2721 Bedienungsanleitung

Johnson Controls

Johnson Controls M300CJ-R Bedienungsanleitung

Johnson Controls

Johnson Controls VMA 1410 Installationsanleitung

Johnson Controls

Johnson Controls System 450 Series Bedienungsanleitung

Johnson Controls

Johnson Controls IOM1711 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls IOM3723 Bedienungsanleitung

Johnson Controls

Johnson Controls GM 20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls VP140 L Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung