Johnson Controls CK721-A Bedienungsanleitung

24-10025-121 Revision A

March, 2016

CK721-A

Network Controller

version 3.3

installation and

operation manual

Johnson Controls, Inc.

No part of this document may be reproduced without the prior permission of Johnson Controls, Inc.

If this document is translated from the original English version by Johnson Controls, Inc., all

reasonable endeavors will be used to ensure the accuracy of translation. Johnson Controls, Inc.

shall not be liable for any translation errors contained herein or for incidental or consequential

damages in connection with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls, Inc. shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking your equipment, keep all original manufacturer documentation for reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Acknowledgments

Metasys® and Johnson Controls® are trademarks of Johnson Controls, Inc. All other company and

product names are trademarks or registered trademarks of their respective owners.

Declaration of Conformity

United States: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

The user is cautioned that changes and modifications made to the equipment without approval of

the manufacturer could void the user's authority to operate this equipment.

Canada: CAN ICES-3 (B)/NMB-3(B)

European Union: This product complies with the requirements of the EMC Directive.

This equipment must not be modified for any reason and it must be installed as stated in the

Manufacturer’s instructions. If this shipment (or any part thereof) is supplied as second-hand

equipment, equipment for sale outside the European Economic Area or as spare parts for either a

single unit or system, it is not covered by the Directives.

UNDERWRITERS LABORATORIES® COMPLIANCE VERIFICATION SHEET

CK721-A SERIES INSTALLATION MANUAL

This product is listed under Underwriters Laboratories UL™ 1076 for Proprietary Burglar Alarm

Units and Systems, UL 294 for Access Control Systems Units and Underwriters Laboratories of

Canada ULC/ORD-C1076-86.

When installed at the site the following requirements must be met to comply with these standards.

1. Transient protection devices that are installed must not be removed or defeated.

2. The CK721-A shall be mounted in subassembly S300-DIN-L or S300-DIN-S.

3. The CK721-A in combination with the S300-DIN-L or S300-DIN-S must be connected to a UL

Listed Uninterruptible Power Supply that provides a minimum of 24 hours of AC emergency

power.

4. The tamper switch must be enabled at all times.

5. Systems requiring the use of network hubs, routers, bridges, network switches or the like shall

guarantee these devices are UL Listed for fire and shock in the category control number (CCN)

NWGQ and/or EMRT. These devices shall be installed in a temperature-controlled

environment. The temperature-controlled environment must be maintained between 13 - 35°C

(55 - 95°F) and relative humidity of 85 ± 5% by the HVAC system. Twenty-four hour standby

power shall be provided for the HVAC system.

6. The installer shall incorporate a supply line transient suppression device complying with the

Standard for Transient Voltage Surge Suppressors, UL 1449, with a maximum rating of 330 V.

Supply line transient suppression device is to be used with the power supply to the network

hub(s) routers, bridges and/or network switches.

7. External network hubs, routers, bridges or network switches must use signal line transient

suppression devices complying with the Standard for Protectors for Data Communications and

Fire Alarm Circuits, UL 497B, with a maximum marked rating of 50V.

8. In the CK721-A user-interface, the “Network Polling [LAN]” parameter must not exceed 90

seconds.

9. Modems shall not be used for primary connection to the host computer. Modems have only

been investigated by UL for supplementary use.

10. The following elevator interfaces have not been investigated by Underwriters Laboratories:

Kone, Otis, and ThyssenKrupp.

11. Do not connect equipment to an AC power source that is controlled by a switch.

CK721-A Installation and Operation Table of Contents

24-10025-121 Rev. A

TABLE OF CONTENTS

Chapter 1: Introduction

Other Documentation 1-1

Key Terms 1-2

Unpacking the Equipment 1-4

General Description 1-5

CK721-A Module 1-5

Enclosures 1-6

S300-DIN Modules 1-7

Additional Equipment 1-8

CK721-A System Specifications (All Panels) 1-9

CK721-A Panel Configuration 1-10

Expanded Address S300 Bus Configuration 1-10

Legacy Address S300 Bus Configuration 1-11

System Configuration Example 1-11

Maximum Enclosure Distance 1-12

Network Communications 1-14

TCP/IP 1-14

10/100Base-T Ethernet 1-15

Communication Modes 1-15

CK721-A/P2000 Server Encrypted Communications 1-16

PIV and PIV-I Smart Card (128-bit) Support 1-18

128-Bit Badge Number Requirements 1-18

HID pivCLASS PIV/PIV-I Readers 1-18

HID Hardware PAM (M2000) Solution 1-19

HID PIV/PIV-I Reader Connecting to RDR2S-A or RDR8S Solution 1-20

OSDP Reader Support 1-22

Chapter 2: CK721-A and S300 DIN Enclosures

CK721-A 2-1

LEDs on the CK721-A 2-2

Binary Output 2-3

CK721-A Installation and Operation Table of Contents

24-10025-121 Rev. A

Setting the End-of-Line Switch 2-3

Lithium Battery 2-4

Input Power 2-5

RS485 2-5

Binary Input 2-6

Connecting the Network 2-7

RS232 2-8

Large Enclosure (S300-DIN-L) 2-10

Wiring CK721-A and Modules 2-11

Small Enclosure (S300-DIN-S) 2-13

Verifying DC and Chassis Ground 2-14

Installing CK721-A Module 2-15

No Enclosure 2-16

DIN Rail Mounting 2-16

+24 VDC Connector 2-17

Power Wiring 2-17

Ground Wiring 2-18

Chapter 3: S300 Expansion Enclosures

S300-DIN Enclosures 3-1

S300 Expansion Enclosures 3-1

Chapter 4: User Interface

Important Notes 4-1

Notes on Encryption 4-2

Principle of Operation 4-2

Communicating with the User Interface 4-3

Using your Terminal Emulation 4-4

Navigating Through the User Interface 4-5

Write Flash 4-6

Clearing Database 4-7

Clearing the Flash Memory 4-8

Router Configuration 4-8

Log Out 4-11

Rebooting the Panel 4-11

CK721-A Installation and Operation Table of Contents

24-10025-121 Rev. A

iii

Basic Panel Configuration 4-11

Panel Menu 4-11

Panel 4-12

Direct Programming of the CK721-A 4-14

Panel Screen Description 4-14

Terminal 4-22

RDR8S Input Point and Output Point Disassociation 4-37

RDR2S-A Input Point and Output Point Disassociation 4-38

Configuring PIN Codes 4-39

Assisted Access 4-43

Panel Entry/Exit 4-45

Elevator Access Control 4-46

Cabinet Access Control 4-69

Elevator or Cabinet Terminal 4-70

Output 4-74

Holiday 4-76

Access Group 4-78

Elevator Access Group 4-79

Control Door 4-80

Panel Soft Alarm 4-81

Password Change 4-82

Reboot 4-83

Badge 4-84

Input 4-88

Time Zone 4-92

Card Events 4-94

System Information 4-98

Control Output 4-101

Change Date 4-103

Chapter 5: Maintenance

Routine Maintenance 5-1

Impaired Performance Conditions 5-1

Testing Procedure 5-2

Check Backup Battery Operation 5-2

Lithium Battery Replacement 5-2

CK721-A Installation and Operation Table of Contents

24-10025-121 Rev. A

Field Servicing 5-3

Troubleshooting 5-3

Appendix A: Expanded Address S300 Bus

Appendix B: Performance Analysis

Appendix C: Grounding and Connectors

Cable Grounding C-1

“D-Type” Connectors C-2

Non “D-Type” Grounding Connections C-3

Installations in the USA C-3

Installations in Europe C-4

Card Reader Unit Grounding C-5

Appendix D: Door Open/Aux Access Supervision

Purpose of Supervised Inputs D-1

Configuring the S300-SIO8 D-2

Wiring to the Reader Module D-2

Appendix E: Database Flash Backup from the Host

Appendix F: Using a Keypad Reader on a Panel

Invoking Access Requests from a Keypad F-1

Invoking Air Crew Access Requests from a Keypad F-2

Invoking Timed Overrides from a Keypad F-3

Invoking Panel Card Events from a Keypad F-7

Quick Guide to Using Keypad Readers F-11

Appendix G: Configuring SSH and SFTP Clients

PuTTY Client G-1

WinSCP Client G-7

Appendix H: Wiring Concepts

Wiring Readers H-1

Wiring for Door Controls H-1

Door Strike Wiring H-2

Output Wiring H-4

CK721-A Installation and Operation List of Figures

24-10025-121 Rev. A

LIST OF FIGURES

Figure 1-1: Sample CK721-A System Configuration 1-12

Figure 1-2: 10/100Base-T 4x5 Rule 1-13

Figure 1-3: CK721-A/P2000 Server Encrypted Communications 1-16

Figure 1-4: HID Hardware PAM (M2000) 1-20

Figure 1-5: System with P2000 and CK721-A Controller 1-21

Figure 1-6: System Diagram 1-22

Figure 2-1: Wiring Between RS485B and RDR2S-A Module 2-6

Figure 2-2: Wiring Between Binary Input 1 and Trouble Pin 2-6

Figure 2-3: Hub to CK721-A Wiring 2-7

Figure 2-4: Large Enclosure with Installed Components 2-10

Figure 2-5: One CK721-A Module Mounted in a Large Enclosure 2-10

Figure 2-6: One CK721-A Module and Two RDR2S-A Modules Mounted in a

Large Enclosure 2-11

Figure 2-7: Daisy Chain Module Wiring for S300-DIN-L 2-12

Figure 2-8: Small Enclosure with Installed Components 2-14

Figure 2-9: One CK721-A Module Mounted in a Small Enclosure 2-15

Figure 2-10: CK721-A Module Mounted on a DIN Rail. 2-17

Figure 2-11: +24 VDC Connector (Part of the DC Power Harness) 2-17

Figure 2-12: Wiring Multiple Modules - Overview 2-18

Figure 4-1: CK721-A Controller/P2000 Host Connection Methods 4-3

Figure 4-2: Static Route Examples 4-10

Figure 4-3: Assisted Access Timing Diagram 4-44

Figure 4-4: KONE KIC Controller with Multiple Elevator Groups 4-51

Figure 4-5: KONE KIC Controller with Multiple Elevator Groups and Multiple

CK721-A Controllers 4-52

Figure 4-6: Primary and Backup KONE IP Controllers 4-53

Figure 4-7: ThyssenKrupp Touch Screen 4-54

Figure 4-8: ThyssenKrupp Building Elevator Layout 4-56

Figure 4-9: ThyssenKrupp Serial Elevator Integration System Architecture 4-57

Figure 4-10: Otis Serial E.M.S.Server-Client Elevator Configuration Layout 4-59

Figure 4-11: Otis E.M.S. Master-Slave Elevator Configuration Layout 4-62

CK721-A Installation and Operation Table of Contents

24-10025-121 Rev. A

Figure 4-12: Using Multiple Time Blocks 4-92

Figure B-1: CK721-A Access Time Performance Graph B-2

Figure C-1: Example of D-Type Connector Grounding C-2

Figure C-2: Example of Grounding Shielded Cable at Both Ends C-4

Figure C-3: Example of Grounding Shielded Cable at Only One End C-5

Figure D-1: Input/Output Contact Wiring D-3

Figure E-1: CK705/CK720 Write DB to Flash Dialog Box E-1

Figure H-1: Maximum Distance Between Readers and S300 Expansion

Enclosures H-1

Figure H-2: Example of a Typical CK721-A System H-2

Figure H-3: Field Installed Metal Oxide Varistor H-3

Figure H-4: Field Installed Metal Oxide Varistor H-4

Andere Handbücher für CK721-A

Inhaltsverzeichnis

Andere Johnson Controls Controller Handbücher

Johnson Controls

Johnson Controls METASYS ASC Bedienungsanleitung

Johnson Controls

Johnson Controls EDA-8102 Bedienungsanleitung

Johnson Controls

Johnson Controls MP8 20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls FAC3613 Bedienungsanleitung

Johnson Controls

Johnson Controls FMS-1655 Series Bedienungsanleitung

Johnson Controls

Johnson Controls FAC2611-0U Bedienungsanleitung

Johnson Controls

Johnson Controls Joventa BAS1(S) Bedienungsanleitung

Johnson Controls

Johnson Controls VAP Series Bedienungsanleitung

Johnson Controls

Johnson Controls Metasys DX-9100 Service-Handbuch

Johnson Controls

Johnson Controls LP-FXVMA Series Bedienungsanleitung

Johnson Controls

Johnson Controls CK721-A Kurzanleitung

Johnson Controls

Johnson Controls tyco iSTAR Edge G2 Bedienerhandbuch

Johnson Controls

Johnson Controls SMART EQUIPMENT VERASYS VEC100 Bedienungsanleitung

Johnson Controls

Johnson Controls TEC2664Z-3 BACnet Bedienungsanleitung

Johnson Controls

Johnson Controls VA9104-AGA-1S Bedienungsanleitung

Johnson Controls

Johnson Controls HS3032 Bedienungsanleitung

Johnson Controls

Johnson Controls M9220-GG-3 Series Bedienungsanleitung

Johnson Controls

Johnson Controls VMA1615 Bedienungsanleitung

Johnson Controls

Johnson Controls TC-8902 Bedienungsanleitung

Johnson Controls

Johnson Controls M100C Series Bedienungsanleitung

Johnson Controls

Johnson Controls TEC3000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls M9203-B Series Bedienungsanleitung

Johnson Controls

Johnson Controls FEC26 Series Bedienungsanleitung

Johnson Controls

Johnson Controls M9308-AGA-xZ series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung