Johnson Controls EDA-8100 Montageanleitung

Installation Sheet

Issue Date 0392

1. EDA-8100-1100 Electric Damper Actuator with counterclockwise

spring return, or

EDA-8100-1101 Electric Damper Actuator with clockwise spring

return

2. Two #10 mounting screws

3. Two isolator grommets

ςscrewdriver, flat blade, 1/4 to 5/16 inch and 1/8 inch tips

ςdrill, 5/32 inch (4 mm) drill bit, 1-1/4 inch hole saw

ςadjustable wrench

ςpliers

Figure 1: Electric Damper Actuator

1. Compatibility and torque:

ςuse on dampers having 10 to 12 mm (0.394 to 0.492 inch) square

or 7/16 to 1/2 inch (11 to 12.5 mm) round shafts

ςcompatible with Johnson Controls D-1300 Blade Dampers

ςdelivers 100 in·lb of stall torque

2. Mounting requirements:

ςmounts in any orientation

ςduct or wall must be 16 gauge (0.06 inch or 1.5 mm) or thicker

Note: Order the Universal Mounting Bracket (D-3153-105) to mount on

duct or wall less than 16 gauge.

EDA-8100 Electric Damper Actuator

Kit Includes

Tools Required

Installation

Overview

EDA-8100 Electric Damper Actuator

1. Follow NEC and local electrical codes.

2. Disconnect all power supplies.

3. Observe ranges and limitations for individual model.

4. Do not install the actuator in applications where its failure could result

in personal injury and/or loss of property.

5. Do not install if explosive vapors, corrosive vapors, or escaping gases

will be present.

6. Add protective control devices as needed to prevent undesirable

system failure modes.

For#10 Mounting

Screw(6places)

2.33

(59)

2x1.50

2x0.75

6.94

(235)

8.78

(223)

9.26

(235)

4.65

(118)

Figure 2: Top View Dimension inches

Mounting Caution

Pre-Mounting

EDA-8100 Electric Damper Actuator 3

4.34

(110)

6 in. min*

(3x 0.875)

for 1/2 in. conduit

Rubber Grommet

(2 Required)

* Six inch minimum required for cover removal, field wiring, and field adjustments.

Figure 3: End View Dimension inches

Note: Before starting the job, obtain the damper installation information

to use as a reference when mounting the actuator.

1. Locate the preferred driving blade on the damper.

2. Cut a 1-1/4 inch (32 mm) hole in the duct or wall over the driving

blade pin.

3. Attach the drive pin extension to the drive pin and secure using the

clip provided.

4. Firmly grasp the drive pin extension with a pliers and manually close

the damper blades.

RetainerClip

Drive PinExtension

Figure 4: Rotation

5. Note which direction closes the damper, clockwise (CW) or

counterclockwise (CCW).

EDA-8100 Electric Damper Actuator

Figure 5: Removing Cover

6. Insert a screwdriver under the edge of the plastic cover to gently pry

off the cover. See Figure 5.

7. Verify the mode of operation for the proper model number from

Table 1.

Table 1: Operation Modes

Product Code

No. Drive

Type Travel

Time Spring

Return

EDA-8100-1100 incremental 180 second counterclockwise

EDA-8100-1101 incremental 180 second clockwise

Note: The actuator can be mounted in any orientation.

1. Position the actuator onto the drive pin extension so that the actuator

sits against the duct.

2. Use of the actuator’s center mounting slots with the isolation

grommets is the preferred mounting arrangement. If the duct or wall

is less than 16 gauge (0.06 inch or 1.5 mm), order and use the

Universal Mounting Bracket (D-3153-105).

Note: Because of eccentric motion of the actuator that occurs when using

shafts smaller than 10 mm (0.394 inch) square or 1/2 inch

(12.5 mm) round, use of the isolation grommets in the center

mounting slot is required.

3. Mark the location of the actuator's top and bottom mounting slots on

the duct or wall.

4. Remove the actuator and set aside.

5. Drill 5/32 inch (4 mm) holes in the duct or wall at the marked

locations.

Mounting

EDA-8100 Electric Damper Actuator 5

6. Slide the actuator onto the drive pin extension.

7. Secure the actuator to the wall or duct with the screws and isolation

grommets included in the kit.

8. Tighten the two square-head screws on the actuator coupler.

Note: The cover should remain off until the wiring is completed.

CAUTION: Disconnect all power before wiring the actuator to

avoid electrical shock or damaging the equipment.

Opening Covers

ConduitOpening

Figure 6: Conduit Openings

1. Insert the leads from the controller through one of the three openings.

2. Install the black plugs in the other two conduit openings. See

Figure 6.

Wiring

EDA-8100 Electric Damper Actuator

24 VAC Input Power

Clockwise 24 VAC

Control Signal

Counterclockwise

24 VAC Control Signal

Common

COMCCW CW PWR

FT1

FT2

FT4

FT3

FT6

FT5

FT7

Figure 7: Wiring Connections

3. Connect the leads to Terminal Block 1 (TB1) as shown in Figure 7.

1. Apply power.

2. Use the checkout procedure described in the controller instructions to

check the action of the actuator.

3. Run the actuator fully CW and CCW.

4. Verify that the damper blades fully open and close.

5. Install the plastic cover.

Checkout

Procedure

EDA-8100 Electric Damper Actuator 7

The EDA-8100 is not field repairable. For a replacement, contact the

nearest Johnson Controls branch office or your wholesale distributor.

Replacement

EDA-8100 Electric Damper Actuator

Notes

Controls Group

507 E. Michigan Street

P.O. Box 423

Milwaukee, WI 53201

Inhaltsverzeichnis

Andere Johnson Controls Controller Handbücher

Johnson Controls

Johnson Controls A28 Series Bedienungsanleitung

Johnson Controls

Johnson Controls Metasys FAC4911 Bedienungsanleitung

Johnson Controls

Johnson Controls M9106-AGx-2N0x Series Bedienungsanleitung

Johnson Controls

Johnson Controls Metasys FAC4911 Bedienungsanleitung

Johnson Controls

Johnson Controls G861 Series Service-Handbuch

Johnson Controls

Johnson Controls TRUE RH HC-67x3 Bedienungsanleitung

Johnson Controls

Johnson Controls VA-7480 Bedienungsanleitung

Johnson Controls

Johnson Controls TEC2245-4 Bedienungsanleitung

Johnson Controls

Johnson Controls Facility Explorer FX20 Bedienungsanleitung

Johnson Controls

Johnson Controls EDA-8000 Handbuch

Johnson Controls

Johnson Controls VA7820-GG-1 Series Bedienungsanleitung

Johnson Controls

Johnson Controls LP-NRM653-000C Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco KT-1 Bedienungsanleitung

Johnson Controls

Johnson Controls VMA1200 Series Bedienungsanleitung

Johnson Controls

Johnson Controls FEC16 Series Bedienungsanleitung

Johnson Controls

Johnson Controls VA9208-GG Series Bedienungsanleitung

Johnson Controls

Johnson Controls NAE Bedienungsanleitung

Johnson Controls

Johnson Controls FAC3611 Bedienungsanleitung

Johnson Controls

Johnson Controls LN-DSWSC1-0 Bedienungsanleitung

Johnson Controls

Johnson Controls LN Series Bedienungsanleitung

Johnson Controls

Johnson Controls FX-PCA3611 Bedienungsanleitung

Johnson Controls

Johnson Controls M9132-AG -1N Series Bedienungsanleitung

Johnson Controls

Johnson Controls M9320-AUA-4 Bedienungsanleitung

Johnson Controls

Johnson Controls CIS01 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung