Johnson Controls PG9350SL Bedienungsanleitung

User manual

PG9350SL

Wireless photoelectric beam detector

Detector features

•Battery saving function

•IP65 waterproof rating, not evaluated by UL

•4-channel beam frequency selector

•Environmental disqualification circuit for configuring behavior in adverse weather conditions

•Tamper function

•Outdoor detection range of 350 ft

Introduction

The PG9350SL is a PowerG wireless photoelectric beam detector that provides protection for outdoor perimeters.

Warning: Failure to follow the instructions provided with this device, or improper handling, may cause death or

serious injury.

Safety information

Warnings

•Do not use the product for purposes other than the detection of moving objects such as people and vehicles.

•Do not use the product for unintended purposes, such as activating a shutter, which may cause an accident.

•Do not touch the product when it is wet or touch the unit base or power terminals of the product with wet hands. It

may cause electric shock.

•Do not pour water over the product as it may cause damage.

•Never attempt to disassemble or repair the product. It may cause fire or damage to the devices.

•Do not use batteries that have different levels of power remaining, that is, new and used batteries. Not observing

these guidelines may result in an explosion, leakage of electrolyte, emission of toxic gases, or other outcomes that

may be harmful to people and property.

•When handling batteries, do not recharge, short circuit, crush, disassemble, exceed heat above 100°C (212°F),

incinerate, or expose the contents to water. Do not solder directly to the cell. Not observing these guidelines may

result in fire, explosion, or severe burn hazard.

•Clean and check the product periodically for safe use. If any problem is found, stop using the product, and have

the product repaired by a professional engineer or electrician.

Box contents

•Transmitter and receiver modules

•Product documentation

•Hardware pack

Accessories

Figure 1. Accessories

Parts identification

Figure 2. Parts identification

Ordering detector batteries

The specified batteries for the device are four (4) LSH20 batteries manufactured by SAFT, two for the transmitter

and two for the receiver.

For information about batteries, visit the following website and contact your local SAFT sales

representative. See

https://www.saftbatteries.com/products-solutions/products/ls-lsh-lsp

Disassembling the device

Disassemble the device before enrolling and mounting.

1. Loosen the cover lock screw with a screwdriver.

Figure 3. Loosening the cover lock screw

2. Place a coin in the recess and twist slightly to unlock the cover.

Figure 4. Unlocking the cover

3. Pull the cover from the back of the device.

Figure 5. Removing the cover

4. To remove the main unit from the chassis, turn the optical unit 90° and remove the screws from both sides.

Figure 6. Removing the screws from the main unit

5. Pull the upper part of the main unit forward and up to remove it.

Figure 7. Removing the main unit

Caution: Do not place the main unit where it is exposed to direct sunlight. Doing so may cause damage to the

product.

6. Loosen the 5 screws from the back cover and remove the chassis from the back-box.

Note: Complete the Disassembly process for both the transmitter and receiver before mounting the device.

Enrollment

Compatible panels

•PowerSeries NEO (v1.37 and higher)

•PowerSeries Pro (v1.31 and higher)

•IQ2+ (v2.6.2 and higher)

•IQ Hub (v3.0.1 and higher)

•IQ4 (v4.0.1 and higher)

Enrolling the device

The device begins the enrollment process when the PowerG module is powered on. The PowerG module is a card in

the detector.

Note: Enroll both the transmitter and receiver onto the control panel. The modules can be enrolled in any order.

Figure 8. Internal view

PowerG daughter card

PowerG power switch

Configuration dipswitches

Configuration

Dipswitch 1

Dipswitch 2

Receiver

Transmitter

Off

1. Ensure the control panel is in enrollment mode.

2. Install batteries in the detector.

3. Turn the PowerG module power switch located on the interface board to the ON position. Refer to the control

panel installation manual for a complete set of enrollment instructions.

If the automatic enrollment procedure fails, refer to the control panel instructions and enroll the device

manually.

4. Optional: Configure any optional settings on the interface board. For more information, see the Optional

settings section.

5. Important! Turn the switch to the OFF position and remove the batteries. Reinsert the batteries after you

mount the device.

Note: Complete enrollment for both the transmitter and receiver before mounting the device.

Mounting

Figure 9. Mounting guidelines

Do not mount the device on an unstable surface

Do not mount the device on an unstable pole.

Do not mount the device near trees or other objects that may block the beam.

When mounting on a pole, the pole diameter size should be 34 mm - 48 mm (1.34 in - 1.89

in).

Direct sunlight can affect device performance. Avoid mounting the device where it is

exposed to a lot of direct sunlight.

Mount the device at a height of 0.7 to 1m (2.3 ft to 3.3 ft).

Mount the device at least 1 m (3.3 ft.) away from a wall or fence that is parallel to the beam.

Do not mount the device where the infrared beam from a different model can reach the

receiver.

Important: Completely install all components of the detector to comply with the IP65 standard requirements.

Additional guidelines

•Avoid cables being caught between the chassis and back-box when mounting this device.

•If you accidentally open an unnecessary knockout, be sure to fill the knockout. Not doing so may result in

waterproof failure and malfunction of the product. Use either silicone sealant or plastic putty. Do not use Siloxane

as this may corrode the PCB. Sealant with less than 0.1% Siloxane is acceptable.

•Do not touch or move the optical unit when mounting the cover. This may shift the optical axis and require a

readjustment.

•Avoid mounting the transmitter and receiver at a 45 ° angle as shown below. This reduces the detection range by

50%.

Figure 10. Reduced detection range

•Ensure the waterproof packing is attached before mounting to preserve the IP rating of the device.

Figure 11. Attaching the waterproof packing

Mounting on a wall

1. Using a screwdriver or similar tool, break the six knockouts in the back-box. The knockout positions are

marked WALL.

Figure 12. Preparing the back-box for mounting

2. Mount the back-box to the wall with the 4x20 screws. If two detectors are installed, the distance between the

upper and lower detector should be at least 20 mm (0.78 in.). If mounting in a corner location, ensure the

distance from the side wall is at least 1 m (3.2 ft). Use a pitch of 83.5 mm (3.3 in.) when connecting to a gang

electric box.

Figure 13. Mounting the back-box

3. Insert two batteries into the lower battery recess of the back-box and set the RF module switch to the ON

position.

Figure 14. Inserting the batteries

4. Pull the cable through the chassis and tighten the screws. Tighten the screws in this order:

a. Middle

b. Top left

c. Bottom left

d. Top right

e. Bottom right

Caution: Tighten the screws completely by torque of 1.0 - 1.5 N·m. Not doing so may cause malfunction of the wall

tamper.

Figure 15. Attaching the chassis

5. Insert the lower part of the main unit and push down to fix it onto the chassis.

Figure 16. Inserting the main unit

6. Turn the optical unit 90 degrees and tighten the screws on both sides.

Figure 17. Adjusting the optical unit

7. Place the cables behind the blue rubber cones to prevent them catching under the main cover.

Figure 18. Securing the cables

Andere Handbücher für PG9350SL

Inhaltsverzeichnis

Andere Johnson Controls Sicherheitssensor Handbücher

Johnson Controls

Johnson Controls FS-1300 Bedienungsanleitung

Johnson Controls

Johnson Controls LC-203 Bedienungsanleitung

Johnson Controls

Johnson Controls DSDN Bedienungsanleitung

Johnson Controls

Johnson Controls tyco Bentel Security BW-IRC Bedienungsanleitung

Johnson Controls

Johnson Controls PG9200AX Bedienungsanleitung

Johnson Controls

Johnson Controls PGP914 Bedienungsanleitung

Johnson Controls

Johnson Controls PG9200AX Bedienungsanleitung

Johnson Controls

Johnson Controls LC-200 Bedienungsanleitung

Johnson Controls

Johnson Controls MP-802 PG+ Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco Kantech T.REX Montageanleitung

Johnson Controls

Johnson Controls tyco Bentel Security BW-DTM Bedienungsanleitung

Johnson Controls

Johnson Controls LC-203 Bedienungsanleitung

Johnson Controls

Johnson Controls HTD-432 PG2 Bedienungsanleitung

Johnson Controls

Johnson Controls NEXT CAM PG+ Merkblatt

Johnson Controls

Johnson Controls LC-224 Bedienungsanleitung

Johnson Controls

Johnson Controls LC-200S Bedienungsanleitung

Johnson Controls

Johnson Controls PG9350SL Bedienungsanleitung

Johnson Controls

Johnson Controls tyco Bentel Security BW-SHK Bedienungsanleitung

Johnson Controls

Johnson Controls PGP922 Bedienungsanleitung

Johnson Controls

Johnson Controls F62AA Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco SR Series Bedienungsanleitung

Johnson Controls

Johnson Controls FTX-P2J Bedienungsanleitung

Johnson Controls

Johnson Controls PG8932 Bedienungsanleitung

Johnson Controls

Johnson Controls RLD-H10G Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung