Joney JYF-3002 Bedienungsanleitung

Contents

1Introduction of the fingerprint lock....................................3

1.1 Feactures....................................................................................3

1.1.1 Brief Introduction...................................................................4

1.1.2 Introduction of functions........................................................4

1.2 Diamensions...............................................................................4

1.3 Technical data.............................................................................5

2Operation..............................................................................6

2.1 Ways to put the finger.................................................................6

2.2 Setting Card + password............................................................6

2.3 Setting fingerprint + password + card...........................................6

2.4 Alarming Function..........................................................................16

2.4.1 Low voltage alarm...............................................................16

2.5 Backup power................................................................................16

2.6 Installing / replacing batteries........................................................16

2.6.1 Installing batteries...............................................................16

2.6.2 Replacing batteries.............................................................16

2.7 Remarks........................................................................................17

3Installation Procedures .....................................................17

3.1 Opening pores on the door.......................................................17

3.2 Opening pores on lock holder case..........................................18

3.3 Installation procedures .............................................................19

4Maintenance and upkeep ..................................................22

4.1 Daily maintenance and upkeep ................................................22

4.2 Notice for use ...........................................................................23

5After-sale Service...............................................................26

5.1 Remarks about after-sale service.............................................26

5.2 Packing List ..............................................................................26

5.3 Accessories ..............................................................................27

A/2(2013 年7月)

Important Tips

1. Fingerprint lock is a kind of hi-technical product, and its normal

operation and life span are directly influenced by the installation.

Therefore, we kindly suggested you to call in a professional to install it.

Please open pores, supporting pits, buckle and buckle pores

according to the indication of opening pore in the door plank. Pores

should be opened accurately and the lock should be installed

according to the indication strictly. If the lock cannot be opened

(smoothly) after installation, please contact with the local distributors

or our after-sales department to solve the problem.

2. If your house is sprucing up, it is suggested to uninstall the lock after

you exanimate the locks and to reinstall them after the sprucing up.

The aims are: 1. To avoid the lock appearance being damaged by

corrosives, and the wet paint on the door will influence the gearing of

the lock. 2. Ethyl alcohol, paint and other chemicals will be used when

we sprucing up the house, which will be volatized to accelerate to

damage the lock appearance and shorten its life span.

3. Before installation, please switch on all of the connecting wire and

load the batteries, and then press the initialized button to initialize the

lock and restore factory defaults.

4. When installing the lock, please do take the mechanical keys with you

so as to unlock it if the door is close before you finish the installation.

Registration Form of Users

For convenience, we make this form for administrator to record

information of user registration. You can also make you form according to your

specific requirements.

No.

Department

Name

Fingerprint

No.

Date of

registration

signature

Remarks

1 Introduction of the fingerprint lock

1.1 Feactures

1.1.1 Brief Introduction

Features : Delicate appearance design, Reasonable structure, Secure

fingerprint lock.

Applications: Government, Police station, Army, Bank, Law Court, Hospital,

Office building, Residential area, etc.

1.1.2 Introduction of functions

Adopting the international advance biotechnology to ensure its high quality;

4 peaces AA batteries; handles can prevent the wreaking havoc;

Unlocking methods: 1. Fingerprint + Password + mechanical key; 2. Card +

password + mechanical key.

1.2 Diamensions

1.3 Technical data

No.

Items

Technical parameters

Sensor resolution

Bright background, 500dpi

Sensor damage resistance

ability

1000 times of impact with 4H pencil

Starting time

<1 second

Way of contrast

1：N

False rejection rate

≤1%

Error rate

≤0.0001%

Finger point

360°

Fingerprint registration module

Create one fingerprint module at one

time

Fingerprint update mode

Auto update

Fingerprint information

The fingerprint information will not

lose when the battery is off or

changed

Fingerprint capacity

100 Pieces

Lights interfere

Avoid explosion under high light

Fingerprint collector

Hard glass, nanometer surface

treatment

Static Power Consumption

< 30 u A

Dynamic Power Consumption

The working current is under 200 mA

Control system

Dicaryon dual circuit and individual

control

The fingerprint battery life

Open door for 5000 times

The combination battery life

Open door for 6000 times

Working voltage

DC 6 V

Power supply mode

Battery powered

Combination capacity

100 Groups

backup power

DC 9 V

Low voltage alarm

4.9 V

Antistatic ability

Contact discharge 8KV，air discharge

15KV

Working temperature

-10℃to 55℃

Working humidity

10% to 90%

Storage temperature

-20℃to 7 0℃

Combination design

Random combination

Combination length

6-digit numbers

Door open method

Left open, right open

(Remark: We emphasize the technology updating, we keep the right to

notice you if parameters are changed)

2 Operation

2.1 Ways to put the finger

Remarks: please notice to put your finger in the right position

Please put your finger on the fingerprint acquisition windows with moderate

force and keep flat because the central of the fingerprint contents most of the

information. Compare the right and wrong way of putting finger as below:

手指须放置在指纹采集窗中心

保持手指平放在指纹采集窗

轻轻地把手指按在指纹采集窗

保持平稳（不要向前或向后滑）

Lock-out function

Pull the handle upwards inside or outside the door can make it lock out and

realize the function of anti-theft bolt. Rotate the small knob in the back of the

lock 45 degrees, the door will be deadlock, and it cannot be opened outside in

any ways.

2.2 Setting in the mode of Card + password

Mifare card password lock has the following two methods to unlock:

1. Stand-alone (independent): Mifare card or password alone to open the

door.

2. Combined: Mifare card and password are used together to open the

door.

Note:

1. The system locks Initialized from the factory, the first management

password is 12345678, unlock method is stand-alone model.

1.1 Change Stand-alone model to the combined model:

Enter 8-bit management password，press key button and then press “6

“button, buzzer 6 sounds, blue light flashing, then press key button to

confirm, the buzzer "beep "long, you have change the model successfully. If

you want to exit, press the“*“button;

1.2 Change combined model to the Stand-alone model:

Put in 8-bit management passwords, then press “5 “button , buzzer 5

sounds, blue light flashing, then press the key button to confirm, the buzzer

"beep "long, you have change it successfully. If you want to exit, press the *

button;

2. In combination mode, if swipe the card first(or enter a password before

pressing the key button) there would be sounds of "di di", blue lights

flashing.Then put in the password and press the key button (or swipe the

card) in 10 seconds, blue light on and the door unlocked.

Mifare Card Operation Manual:

⑴Management Card

Function: setting and clear the effective unlocking card; unlock the

door.

⑵Unlocking card

Function: unlocking the door and set the stay-open state.

⑶Mechanical key

Function: emergency unlocking the door, setting and managing the

management card.

Note: Before put in the password, please brush touch the button panel

until the backlit blue lights on. Then you can put in password.

1. Setting and clearing the management card

1.1 Pressing the initial button on the breadborad for 5 times can empty

all the cards and password.

1. 2 Pressing the initial button on the breadborad for 5 times and read

the first card, a short “beep” and a long “beep” indicate this card is set

as the management card.

2. Adding unlocking cards

2.1 Enter the setting card state:

Read the management card, the buzzer sound a "beep", the motor

rotating, blue lights flashing, then you can open the door. The light will

be off after you unlock. If you do not open the lock and read the

management card, there will be a sound of “beep”, blue light flashing

slowly, this is enter into the setting unlock card state, the card it reading

is the unlock card. Within 5 seconds if the lock hasn’t detected the valid

IC card, then you will hear two short beeps "beep, beep", the unlock

card key card was setting well.

2.2 Process of setting unlocking card:

Entry the Setting key state, take the IC cards close to the inductive

area of lock, if setting the card success, you will sound a short "beep"

and then a long "beep". Repeat this operation, you can set other

unlocking cards. If this card already exists, then the buzzer will sound 2

short beeps of "Didi". 200 unlocking cards are available at most.

3. Clearing the unlocking card

3.1 Clearing single one unlocking card

Read the management card 3 times, there will blue light flashing, put

the card key you want to clear nearing to the inductive area and read it

once, a short' beep' and a long' beep', means that the card has been

clearws successfully. Repeat this operation to delete the other door

cards. If the card does not exist, then the buzzer sounds 6 short beeps.

3.2. Clear single one lost unlocking card

Inhaltsverzeichnis

Andere Joney Sperren Handbücher

Joney

Joney JYF-3001 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung