JTS TG-98STX Bedienungsanleitung
Thank you for choosing the JTS wireless system. In order to obtain the best eciency from the
system, you are recommended to take a few minutes to read this instruction manual carefully.
1. Important Cautions
2. Introduction
3. Specication
4. Parts Identication & Accessories
5. Preparing procedures & basic operation
6. Loop Out Application
1
1
2
3
5
8
INDEX
TG-98STX Stationary Transmitter
1
1. Important Cautions
2. Introduction
• Make all connections before plugging the unit into an AC power outlet.
• Do not leave the devices in a place with high temperature or high humility.
• Do not handle the power cord with wet hands.
• Keep the devices away from re and heat sources.
• This stationary transmitter TG-98STX provides an option for xed
installation to the TG-98RA. It can expand coverage of the wireless system
by using antenna booster, directional antenna and antenna combiner.
• TG-98STX preset 6 groups each of up to 23 channels.
TG-98STX Stationary Transmitter
2
3. Specication
TG-98STX
Carrier Frequency Range 502 ~ 960MHz
RF Output Power Hi / Low
Nominal Frequency Deviation
(modulation) ± 40KHz
Audio Input Impedance 20KΩ
Nominal Input Level -20 DBV
Maximal Input Level 0 dBV
LED Display AF Level, Channel
Audio Input Connector
2 x Balanced XLR /
Ø6.3mm Combo input CH.1
Ø6.3mm Combo input CH.2
Output Monitor Connector 1 x Ø3.5mm stereo phone
jack
Loop Out Connector 2 x Ø6.3mm Balanced
Loop Out Connector
Operation Voltage 12-18 VDC, 450 mA
Dimension (m / m) 212mm(W)* 44mm(H)*239mm(D)
Channel 6 groups each of up to 23 channels
3
4. Parts Identication & Accessories
1413121110916
15
TG-98STX
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
8
2 543
1 3
Power On / O switch
LED Display
Channel / Group Selector
Set button
Volume control
Monitor volume control
Ø3.5mm Stereo Phone Jack
Antenna
DC input ( 12~18V 450mA )
Balanced Loop Out Connector CH.1
Balanced Loop Out Connector CH.2
Balanced XLR/Ø6.3mm Combo
Input / CH.1
Balanced XLR/Ø6.3mm Combo
Input / CH.2
BNC Antenna Output Socket
Monitor input (mono Ø6.3mm phone jack)
Input CH1 48V phantom power switch
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
1
TG-98STX
7 6
4
RM-901 Rack Mount Kit
RTF-1 Antenna Extension Cable
Optional Accessories
18
17
17 18
5
5. Preparing procedures & basic operation
(1) Connect the main unit
Connect the DC INPUT in the rear panel of TG-98STX to an AC to DC adaptor.
(2) Basic operation
1. Connect the mixer output to the XLR / Ø6.3mm combo CH1 input at the rear panel
of TG-98STX with AF input cable.
2. Connect the gooseneck mic and gooseneck mic base at the XLR / Ø6.3mm combo
CH2 input at the rear panel of TG-98STX with AF input cable.
3. Connect the TG-98STX or CS-1CU at the Ø6.3mm mono CH3 input at the rear
panel of TG-98STX with AF cable as an source for interpretation.
NOTE 1:
Two balanced XLR / Ø6.3mm combo inputs are provided. You may use either one
input or both for a stereo source. Also, two balanced Ø6.3mm loop out connectors
are provided for multiple systems application.
NOTE 2:
CH3 is an input signal only for monitoring through monitor headphone and will not be transmitted.
ST-5030i
CS-1CU
TG-98STX
AC to DC adaptor
XLR/Ø6.3mm COMBO INPUT
or
TG-98STX
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
6
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
POWER
CH1/CH2 VOLUME
Group CHANNEL
MONITOR
ANTENNA OUT
CHANNEL
1 2 45
3
Monitor
CH1/CH2 CH3
CH1 CH2
CHANNELGROUP
TG-98STX
(3) LCD Display
AF Level of CH1
AF Level of CH2
Monitor channel display
Channel display
Group
(4) Attach the antenna
The user-friendly antenna comes with BNC
connector. Connect the antenna on the rear of
the transmitter and align it upward.
(5) Power On / O
Turn on or turn o the transmitter by pressing
the“POWER” button.
(6) Volume
Adjust the volume to a proper level.
(7) Monitor Volume
Adjust the monitor volume to a proper level.
Note that by pushing Monitor Volume user can
choose CH1 / CH2 or CH3 to listen.
(8) Select channal
1. Press “set”button for about 3 second and
then“.”starts ashing on the pannel.
2. Press ”+ ”or ”- ”button to increase or
decrease the channel /Group number.
3. Press“set”button again to store the channel
/ Group.
1
2
3
4
5
7
(9) Set the rubber pad
Four self-adhesive rubber pads are provided to ensure the stability.
They are to be placed on the bottom of the transmitter.
(10) RTF-1 Antenna Extension Cable (Optional)
Antenna extension cable enables front mounting antenna which
benets the RF eeciency.
(11) RM-901 Rack Mount Kit (Optional)
Rack mount kit is available to install the half rack transmitter into a standard EIA rack.
+
-
+
-
+
-
Inhaltsverzeichnis
Andere JTS Sender Handbücher
JTS
JTS PT-920BG Bedienungsanleitung
JTS
JTS Monacor International PT-950B/5 Bedienungsanleitung
JTS
JTS PT-950B/2 Bedienungsanleitung
JTS
JTS PT-850B Bedienungsanleitung
JTS
JTS PT-990B Bedienungsanleitung
JTS
JTS PT-920B/5 Bedienungsanleitung
JTS
JTS US-8010 Bedienungsanleitung
JTS
JTS IN-64TH Bedienungsanleitung
JTS
JTS PT-920B Bedienungsanleitung
JTS
JTS PT-36BG2/5 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
