JUKI IP-200 Benutzerhandbuch

ENGLISH

IP-200 SET-UP MANUAL

Operating power voltage of this product is DC+24V and DC+5v.

CONTENTS

!. OUTLINE ........................................................................................................................1

@. CONTENTS OF THE ARTICLES PACKED TOGETHER ..............................................1

1. For those who have purchased the machine provided with IP-200 operation panel .......................1

2. For those who have purchased the single unit of IP-200 operation panel ........................................1

#. INSTALLING IP-200 ON TABLE/STAN AND CONTROL BOX .....................................2

1. Installing procedure of the operation panel and the installing base .................................................2

2. Connecting the cord and turning ON the power ..................................................................................2

$. EXPLANATION OF THE OPERATION PANEL .............................................................3

CONNECTING PROCEDURE OF OPERATION PANEL WITH EXTERNAL VEHICLE

......4

1. Smart media card ...................................................................................................................................4

2. RS-232C ...................................................................................................................................................6

3. Input of signal by means of the connector for external input ............................................................7

^. RE-SETUP OF THE PROGRAM OF THE OPERATION PANEL ...................................8

&. RE-SETUP OF MAIN PROGRAM ................................................................................11

1. When panel program matches with main program ...........................................................................11

2. When panel program does not match with main program and an error occurs ............................14

*. RE-SETUP OF SERVO PROGRAM ............................................................................17

1. When main program matches with servo program ...........................................................................17

2. When panel program does not match with main program and an error occurs ............................20

(. WHEN USING SMART MEDIA OTHER THAN THAT WHICH HAS BEEN

PACKED TOGETHER ..................................................................................................23

– 1 –

IP-200 operation panel

main unit

* 1, * 2

!. OUTLINE

Operation panel of IP-200 can realize various functions in combination with the control box.

@. CONTENTS OF THE ARTICLES PACKED TOGETHER

1. For those who have purchased the machine provided with IP-200 operation panel

1 IP-200 operation panel main unit ...........................................................1 set

2 Operation panel installing base ..............................................................1 set

3 Operation panel installing base setscrew ............................................. 2 pcs.

4 Set-up manual and CD-ROM (this CD-ROM) for instruction manual ....1 pc.

5 When using IP-200 ............................................................................... 1 pc.

5 articles above and components related to control box are packed together.

2. For those who have purchased the single unit of IP-200 operation panel

1 IP-200 operation panel main unit ...........................................................1 set

2 Operation panel installing base ..............................................................1 set

3 Operation panel installing base setscrew ............................................. 2 pcs.

4 Set-up manual and CD-ROM (this CD-ROM) for instruction manual .....1 pc.

5 When using IP-200 ................................................................................ 1 pc.

6 Smart media card ...................................................................................1 pc.

7 Write prohibition seal .............................................................................1 sheet

7 articles above are packed together.

* The set-up manual and the form of simpliﬁed instruction manual are not packed together.

* 1

* 2

Operation panel installing

base

Operation panel installing

base setscrew

When using IP-200 Smart media card Write prohibition seal

* 1, * 2

* 1, * 2 * 1, * 2

* 2 * 2

Set-up manual and CD-ROM

(this CD-ROM) for instruction manual

– 2 –

#. INSTALLING IP-200 ON TABLE/STAN AND CONTROL BOX

1. Installing procedure of the operation panel and the installing base

1) When installing the installing base, install it on the

table with the screws supplied as accessories.

At this time, consider the position of the hole for

wiring opened in the table to install the base.

In case of the table without the hole for wiring,

install the base at the position where there is no

trouble when the machine head is tilted or sewing

is performed.

2) Operation panel can be fixed to the installing

base since the magnet on the rear of the

operation panel adheres to the installing base.

Besides, operation panel can be installed on the

metal part such as the side of the control box to

which the magnet adheres.

Do not put the articles which have little

resistance against the magnet near the

operation panel.

2. Connecting the cord and turning ON the power

1) Pass the cord of the operation panel through the

hole for wiring in the table and connect it with the

control box under the table. For the table without

the hole for wiring, wire the cord at the position

where there is no trouble when the machine head

is tilted or sewing is performed, and connect it

with the control box. For the connection of the

connector, connect it to CN34 of MAIN circuit

board in the control box or built in the machine

head. For the details, refer to the Instruction

Manual for the sewing machine main unit.

When the work above has been completed, turn

ON the power.

When connecting the cord, make

sure that the power of the main unit is

turned OFF. When connecting the cord

in the state that the power is turned

ON, trouble or breakage of the circuit

will be caused.

MAIN circuit board

CN34

WARNING :

Turn OFF the power before starting the connecting work so as to prevent accidents caused by abrupt

start of the sewing machine.

– 3 –

1 LCD display section • Touch panel

2 Ready key

3 Information key

4 Communication key

5 Mode key

6 Smart media card slot

7 Slide switch (Not used : OFF)

8 Connector for communication by RS-232C

9 Variable resistor for Color LCD screen contrast regulation

!0 Connector for external input

$. EXPLANATION OF THE OPERATION PANEL

Explanation of the respective parts of the operation panel is given below.

For the details of the respective parts, refer to "1. NAME OF EACH SECTION OF THE OPERATION

PANEL" of the Instruction Manual.

– 4 –

CONNECTING PROCEDURE OF OPERATION PANEL WITH EXTERNAL VEHICLE

It is possible for this operation panel to perform communication or input of signal with the vehicles below

other than the control box.

1. Smart media card

2. RS-232C

3. Input of signal by means of the connector for external input

Connecting procedure is given below.

1. Smart media card

It is possible to give and take data by using the smart media card.

For the smart media card, it is recommended to use SmartMedia of 3.3V voltage type which is prescribed

by SSFDC forum. The card is different in the position of notch as shown in the ﬁgure below. Judge it by

the position of notch.

When the contact part becomes dirty, contact failure will be caused. Control so that the

contact part is not touched by hand, or that dust, oil or other foreign material does not

adhere to the contact part. Besides, be very careful of handling the card since the internal

data is broken by the static electricity or the like.

(1) Setting procedure

1) When the upper side cover located on the side of

operation panel is opened, there is the inserting

opening of the smart media card. Insert the card

there while facing the contact part to the front.

2) When continuing inserting the smart media card, the card stops once in the state that it protrudes

by approximately 10 mm. When some force is applied to it, it is further inserted and goes to the end.

When it goes no further, reduce the force and it returns by approximately 1 mm. This work completes

the setting of the card.

Contact part

Notch

< 3.3V type > < 5V type >

– 5 –

3) When the setting of the card is completed, close the smart media card cover. It is not possible

to receive or send the data with the smart media card with the cover opened. For the operating

procedure, refer to "USING COMMUNICATION FUNCTION of the Instruction Manual.

If the smart media card comes in contact with the cover and the cover is not closed, check the

following matters.

• Check that inserting is stopped in the state that the card protrudes by approximately 10 mm.

• Check that the coantact part is faced downward and inserted.

• Check that the smart media card other than 3.3V voltage type is used.

(2) Removing procedure

1) Open the smart media cover, press the card until it goes no further and reduce the force. The card

returns by approximately 10 mm by reversing order at the time of setting.

2) Then drawing up the card completes removing.

< Handling the smart media card >

• Smart media is a precision instrument. Do not bend or shock it.

• It is recommended to periodically save the data saved in the smart media into the other vehicle for the

accident.

• When initializing data, perform it after checking that there is no necessary data in the card. When the

data is initialized, the internal data is deleted.

• Avoid using or keeping the card in a high temperature or high humidity place.

• Avoid using the card near heating or combustible articles.

• When the contact part becomes dirty, contact failure will be caused. Control so that the card is not

touched by hand, or that dust, oil or other foreign material does not adhere to the card. Besides, be

careful of handling the card since the internal data is broken by the static electricity or the like.

• Smart media has the life, and writing and deletion cannot be performed after an extended period of

use. In this case, replace the smart media with a new one.

< Prevention of memory error >

• When write prohibition seal 1 is pasted, the card

becomes exclusive for reading and writing cannot

be performed.

• Strip off the seal when you desire to record

again.

• Do not use again the seal which was pasted once

and stripped off. The trouble of the main unit will

be caused.

< 3.3V type >

– 6 –

2. RS-232C

Operation panel can give and take the data with the personal computer by using communication by

means of RS-232C.

For the cable to be connected, connect the reverse type 9-pin (female) to the operation panel side. Signal

names of the operation panel are as follows.

When the contact part becomes dirty, contact failure will be caused. Control so that

the contact part is not touched by hand, or that dust, oil or other foreign material does

not adhere to the contact part. Besides, be careful of handling the contact part since

the internal element is broken by the static electricity or the like.

(1) Setting procedure

1) When the lower side cover located on the side of operation panel is opened, there is a 9-pin connector

for RS-232C. Insert the cable there. When the screw for lock is attached to the connector, tighten the

screw to prevent the screw from falling.

Pin No. Signal name Function Signal direction

1 N.C. Not connected

2 RXD Receive data To panel

3 TXD Transmit data From panel

4 DTR Data terminal ready From panel

5 GND Earth

6 DSR Data set ready To panel

7 RTS Request to send From panel

8 CTS Possible to send To panel

9 N.C. Not connected

– 7 –

3. Input of signal by means of the connector for external input

It is possible to input the signal from the outside.

When the switch is connected, it is possible to use as the input of the production control information.

For the details, refer to "Observing the production control information" of the Instruction Manual.

Cable (separately-sold) as shown in the ﬁgure below

can be connected.

When the contact part becomes dirty, contact failure will be caused. Control so that

the contact part is not touched by hand, or that dust, oil or other foreign material does

not adhere to the contact part. Besides, be careful of handling the contact part since

the internal element is broken by the static electricity or the like.

Connector housing : KYOCERA ELCO CO. 60-8263-3038-15-000

Pin contact : KYOCERA ELCO CO. 60-8263-0513-00-808

Note) The switch main unit is not installed to the

relay cable A (asm.).

1 Relay cable A (asm.) (40008168)

3 2 1

+5V

GND

CN105

– 8 –

^. RE-SETUP OF THE PROGRAM OF THE OPERATION PANEL

When the case is as below, it is necessary to perform re-setup of the program of the operation panel.

™ When the operation panel is used as that for other model.

™ When version-up of the program is performed.

The way of performing setup of the program from the smart media is shown below. Besides, it is regarded

that the program to perform setup has already entered the smart media card.

1) First, turn ON the power. Normally, the sewing ready screen is displayed.

2) Insert the smart media card into the operation panel.

3) Perform operation by the procedure below.

Data edit screen

1) Press key 1 for three seconds.

Communication screen 1

2) Press key 2.

3) Press key 3 .

Data selection screen

4) Press key 4 .

5) Press key 5 .

Inhaltsverzeichnis

Andere JUKI Nähmaschinenzubehör Handbücher

JUKI

JUKI DDL-7000A-7 Series Bedienungsanleitung

JUKI

JUKI SC-510 Originalbetriebsanleitung

JUKI

JUKI JaNets JT Simple Bedienungsanleitung

JUKI

JUKI AK-121 Bedienungsanleitung

JUKI

JUKI IP-410 Bedienungsanleitung

JUKI

JUKI IP-420 Bedienungsanleitung

JUKI

JUKI AE-9 Bedienungsanleitung

JUKI

JUKI AK84 Bedienungsanleitung

JUKI

JUKI MP-G50-TE Bedienungsanleitung

JUKI

JUKI MP-G10-TH Bedienungsanleitung

JUKI

JUKI PS800-8045 Bedienungsanleitung

JUKI

JUKI PS-800SB-2850 Series Bedienungsanleitung

JUKI

JUKI MP-G20R-TH Bedienungsanleitung

JUKI

JUKI DLU-5494N-7/IP-110C Bedienungsanleitung

Beliebte Nähmaschinenzubehör Handbücher anderer Marken

Brother

Brother PR-600/600C Bedienungsanleitung

Brother

Brother SA179 Bedienungsanleitung

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SMT-7242 Bedienungsanleitung

Jack

Jack 6040-D Technisches Handbuch

ZOJE

ZOJE 1900D Bedienungsanleitung

ELNA

ELNA 795-816-116 Bedienungsanleitung

Baby Lock

Baby Lock General Purpose Zig Zag Foot Bedienungsanleitung

ELNA

ELNA 202-248-004 Bedienungsanleitung

Efka

Efka dc 1500 Bedienungsanleitung

Baby Lock

Baby Lock BLQ2-QGF Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MP-G10-AH Bedienungsanleitung

Sullivans

Sullivans Sew & Go Bedienungsanleitung

Sailrite

Sailrite ULTRAFEED 120931 Bedienungsanleitung

Bernina

Bernina Spanish Hemstitch Equipment 47 Bedienungsanleitung

Brother

Brother ScanNCut DX Stamp Starter Kit Bedienungsanleitung

ELNA

ELNA 495-526-20 Bedienungsanleitung

$TEX ALL IN 1 Sleeve Board Pro Bedienungsanleitung$

TEX

TEX ALL IN 1 Sleeve Board Pro Bedienungsanleitung

Husqvarna

Husqvarna VIKING Do All Quilters Hoop Bedienungsanleitung