Juniper BX7000 Bedienungsanleitung

Step 1: Install the BX7000 Multi-Access Gateway 1

BX7000 Multi-Access Gateway

Getting Started Guide

This guide provides instructions on connecting the Juniper Networks BX Series

7000 Multi-Access Gateway to a network. For more information, see the BX7000

Multi-Access Gateway Hardware Guide.

Step 1: Install the BX7000 Multi-Access Gateway

The gateway can be installed in a rack or on a wall. Each installation is site-specific.

For more information, see the BX7000 Multi-Access Gateway Hardware Guide.

Step 2: Connect the BX7000 Multi-Access Gateway to External Devices

Connect the gateway to external devices using the console ports, Ethernet ports,

and T1/E1 ports.

Connect to a Management Console

Use either the RJ-45serial console port or the USB console port to connect to a

management console.

BX 7000

CLOCK CARD

EXPANSION CARD

Console

Terminal Backhaul

Network

Cell Site

NOTE: Although cables can be connected to both the RJ-45 serial console port and

the USB console port, only one of the console ports can be active at a time. If both

ports are connected, only the USB port will be active. For more information

regarding the console ports, see the BX7000 Multi-Access Gateway Hardware Guide.

BX 7000 Multi-access Gateway Getting Started Guide

2Step 2: Connect the BX7000 Multi-Access Gateway to External Devices

Connect to the RJ-45 Serial Console Port

Connect the RJ-45 end of the crossover twisted pair cable to the RJ-45 serial console

port of the gateway. Connect the other end of the cable to the serial port of the

management console.

Connect to the USB Console Port

Connect the Type B end of the USB cable to the USB console port of the gateway.

Connect the Type A end of the USB cable to the USB port of the management

console.

Connect to Ethernet Ports

The Ethernet ports provide connections to external devices and can be used either

as data ports or as management ports.

There are three copper Ethernet ports and two fiber-optic Gigabit Ethernet ports, as

shown in the following illustration:

Connect to T1/E1 Ports

The T1/E1 ports provide connections to T1 or E1 networks. Use an RJ45-to-RJ45

interface cable to connect the gateway to networking devices.

USB console port

Copper Gigabit Ethernet ports

RJ-45 console port

Fiber-optic Gigabit Ethernet ports

CONSOLE COPPER COPPER COPPER SFP SFP

ETHERNET 1

ETHERNET 1 ETHERNET 2 ETHERNET 2

ETHERNET 0

CONSOLE

g002909

NOTE: Although cables can be connected to both the copper Ethernet port and the

fiber-optic Ethernet port, in the case of both the Ethernet 1 port and the Ethernet

2 port, the copper port and the fiber-optic port cannot be active at the same time.

If both ports are connected, only the fiber-optic port will be active. For more

information regarding use of the Ethernet ports, see the BX7000 Multi-Access

Gateway Hardware Guide.

Fiber-optic Ethernet ports

Copper Ethernet ports

COPPER COPPER COPPER SFP SFP ALARM

ETHERNET 1

ETHERNET 1 ETHERNET 2 ETHERNET 2

ETHERNET 0

g002908

Step 3: Connect the Grounding Cable 3

BX 7000 Multi-access Gateway Getting Started Guide

Step 3: Connect the Grounding Cable

The gateway has two grounding studs located on the right side of the front panel, as

well as a grounding screw located on the left side at the back of the gateway for

connecting to the ground when the gateway is wall mounted.

To connect the grounding cable :

1. Before making grounding connections, ensure that the grounding surfaces are

clean and that they are brought to a bright finish.

2. Connect one end of the grounding wire to the ground.

3. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

then connect the strap to one of the ESD points on the chassis.

4. Connect the other end of the grounding cable to either the grounding studs or

the grounding screw.

For more information on grounding the gateway, see the BX7000 Multi-Access

Gateway Hardware Guide.

Step 4: Connect to a Power Source

After grounding, connect the gateway to a power source.

Connect to an AC power source

Use a power cord that has a plug appropriate to your geographical location. For

more information on AC power cord specifications, see the BX7000 Multi-Access

Gateway Hardware Guide.

Connect to a DC power source

To connect the DC power cables:

1. Before connecting to the power supply, verify that the DC power cables are

correctly labeled; and that the customer site power circuit breakers are

switched to the off position.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

then connect the strap to one of the ESD points on the chassis.

3. Secure each power cable lug to the terminal studs. Attach the negative wire lug

to the negative (–) terminal stud and the positive wire lug to the positive (+)

terminal stud.

NOTE: Always ground the gateway before connecting power supplies.

CAUTION: Ensure that the power connections maintain proper polarity.

BX 7000 Multi-access Gateway Getting Started Guide

4Step 5: Power the Gateway On

Step 5: Power the Gateway On

To power the gateway on:

1. Verify that an external management device is connected to a console port on

the gateway.

2. Power the external management device on.

3. Verify that the power supply is fully inserted in the chassis.

4. Verify that the source AC power cord or DC power cables are securely

connected.

5. Switch on the customer site circuit breakers to provide voltage to the power

supply. When the gateway is powered on successfully and diagnostic tests are

complete, the system LED will light green, indicating that the gateway and the

power supplies are functioning normally.

6. Monitor the startup process on the external management device to verify that

the system boots properly. The following messages will be discplayed upon

proper boot :

Completed Successfully.

BX7000 login:

Step 5: Log In to the Gateway

To log in to the gateway:

1. At the login prompt, log in to the gateway either as the CLI user or as the root

user and enter the password.

2. To configure the gateway, enter the configure command at the operational

mode prompt.

cli@BX7000> configure

The symbol # indicates that the gateway is in configuration mode.

cli@BX7000#

For more information on configuration and on using the BXOS software, see the

BXOS Configuration Guide and the BXOS CLI Users Guide and Command

Reference.

Step 6: Configure an Ethernet Management Port

Before you can use an Ethernet port for management, you must assign an IP

address and run an SSH client from a host. For more information, see the BX7000

Multi-Access Gateway Hardware Guide.

Safety Warnings 5

BX 7000 Multi-access Gateway Getting Started Guide

Safety Warnings

Only trained and qualified personnel should install or replace the gateway.

Perform only the procedures described in this guide or the BX7000 Multi-Access

Gateway Hardware Guide. Other services should be performed by authorized

service personnel only.

Before installing the gateway, read the guidelines for site preparation in the

BX7000 Multi-Access Gateway Hardware Guide to make sure that the site meets

power, environmental, and clearance requirements for the gateway.

Read the installation instructions before you connect the gateway to a power

source.

When mounting the gateway in a partially filled rack, load the rack from the

bottom to the top, with the heaviest components at the bottom of the rack.

If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the gateway in the rack.

When removing or installing an electrical component, always place it

component-side up on a flat antistatic surface or in an electrostatic bag.

When installing the gateway, always make the ground connection first and

disconnect it last.

WARNING: See installation instructions before connecting the routing node. This is

a summary of safety warnings; for a complete list, including translations, see the

BX7000 Multi-Access Gateway Hardware Guide at

http://www.juniper.net/techpubs/hardware/.

WARNING: Certain ports on the gateway are designed for use as intrabuilding

(within-the-building) interfaces only (Type 2 or Type 4 ports as described in

GR-1089-CORE, Issue 4) and require isolation from exposed outside plant (OSP)

cabling. To comply with NEBS requirements and to protect against lightning

surges and commercial power disturbances, the intrabuilding ports must not be

metallically connected to interfaces that connect to the OSP or its wiring. The

intrabuilding ports on the gateway are suitable for connection to intrabuilding or

unexposed wiring/cables only. The addition of primary protectors does not

provide sufficient protection to metallically connect these interfaces to OSP

wiring.

CAUTION: Before removing or installing components of a gateway, attach an ESD

strap to an ESD point and place the other end of the strap around your bare wrist.

Failure to use an ESD strap could result in damage to the gateway.

BX 7000 Multi-access Gateway Getting Started Guide

6Safety Warnings

Wire the DC power supply using the appropriate lugs. When connecting power,

the proper wiring sequence is ground to ground, +RTN to +RTN, then –48 V to

–48 V. When disconnecting power, the proper wiring sequence is –48 V to –48

V, +RTN to +RTN, then ground to ground.

Do not work on the system or connect / disconnect cables during electrical

storms.

Before working on equipment that is connected to power lines, remove jewelry,

including rings, necklaces, and watches. Metal objects heat up when connected

to power and ground and can cause serious burns or become welded to the

terminals.

Failure to observe these safety warnings can result in serious physical injury.

Part Number: 530-027716-01

Revision 1

Juniper Networks, Inc.

1194 North Mathilda Avenue

Sunnyvale, CA 94089 USA

Phone 408 745 2000

or 888 JUNIPER

Fax 408 745 2100

Juniper Networks and the Juniper Networks logo are registered trademarks of Juniper Networks, Inc. in the United

States and other countries. All other trademarks, service marks, registered trademarks, or registered service marks in

this document are the property of Juniper Networks or their respective owners. All specifications are subject to change

without notice. Juniper Networks assumes no responsibility for any inaccuracies in this document or for any obligation

to update information in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise

revise this publication without notice.

Revision History

November 2008

BX 7000 Multi-access Gateway Getting Started Guide

Safety Warnings 7

Andere Handbücher für BX7000

Inhaltsverzeichnis

Andere Juniper Tor Handbücher

Juniper

Juniper SRX3400 Montageanleitung

Juniper

Juniper SRX1500 Einrichtungshandbuch

Juniper

Juniper SRX4100 Einrichtungshandbuch

Juniper

Juniper SRX210HE2 Bedienungsanleitung

Juniper

Juniper SRX5400 Montageanleitung

Juniper

Juniper SRX550 Bedienungsanleitung

Juniper

Juniper SRX110 Bedienungsanleitung

Juniper

Juniper SRX650 Bedienungsanleitung

Juniper

Juniper SRX5600 Bedienungsanleitung

Juniper

Juniper SRX100B Montageanleitung

Juniper

Juniper SRX4200 Montageanleitung

Juniper

Juniper SRX5600 Bedienungsanleitung

Juniper

Juniper SRX5400 Bedienungsanleitung

Juniper

Juniper SRX1500 Montageanleitung

Juniper

Juniper SRX650 Montageanleitung

Juniper

Juniper SRX550 Bedienungsanleitung

Juniper

Juniper SRX220 Bedienungsanleitung

Juniper

Juniper SRX5600 Bedienungsanleitung

Juniper

Juniper SRX 1400 SERVICES GATEWAY - Montageanleitung

Juniper

Juniper SRX240 Series Bedienungsanleitung

Juniper

Juniper SRX240 Series Montageanleitung

Juniper

Juniper SSG 500M Series Bedienungsanleitung

Juniper

Juniper SRX300 Series Montageanleitung

Juniper

Juniper SRX 210 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung