Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 MODULE GUIDE REV... Bedienungsanleitung

E Series™ Broadband

Services Routers

E120 and E320 Module Guide

Release

11.3.x

Published: 2010-10-01

This guide provides an overview and description of the line modules (LMs), switch route

processor (SRP) modules, switch fabric modules (SFMs), and input/output adapters

(IOAs) available for the Juniper Networks E120 and E320 Broadband Services Routers.

NOTE: A release may support multiple versions of a module or IOA. For

information, see Software Compatibility in JunosE System Basics Configuration

Guide, Chapter 6, Managing Modules.

Table 1 on page 3 lists the modules and IOAs supported by the router.

This guide also contains the following appendixes:

•IOA Protocol Support on page 49

•Module and Slot Combinations on page 73

•Module Name Cross-Reference Information on page 77

•Product Reclamation and Recycling Program on page 79

For more information about E120 routers, E320 routers, modules, and IOAs, refer to the

following guides:

•Modules that have reached end-of-life—E Series End-of-Life Module Guide

•Module installation and maintenance—E120 and E320 Hardware Guide

•Managing routers—JunosE System Basics Configuration Guide

•Configuring modules—JunosE Link Layer Configuration Guide

E120 and E320 11.3.x Module Guide

Table 1: Modules and IOAs

PageFirst JunosE SupportModule LabelModule/IOA Type

Line Module

57.0.1ES2

LM-4

77.2.0ES2

10G

UPLINK

LM-10 Uplink

98.0.0ES2

10G LM

LM-10

1110.1.0ES2

10G ADV LM

LM-10 ADV

SRP Module

127.0.1SRP-100SRP-100

148.2.0SRP-120SRP-120

167.3.0SRP-320SRP-320

SFM Module

187.0.1SFM-100SFM-100

198.2.0SFM-120SFM-120

207.3.0SFM-320SFM-320

Gigabit Ethernet IOA

217.0.1ES2-S1

GE-4

IOA

GE-4 IOA

257.2.0ES2-S1

GE-8

IOA

GE-8 IOA

299.0.0ES2-S3

GE-20

IOA

GE-20 IOA

337.2.0ES2-S2

10GE PR

IOA

10GE PR IOA

OC3/STM1 ATM IOA

Table 1: Modules and IOAs (continued)

PageFirst JunosE SupportModule LabelModule/IOA Type

377.0.1ES2-S1

OC3-8

STM1

ATM IOA

OC3/STM1-8 ATM IOA

OC12/STM4 ATM IOA

397.0.1ES2-S1

OC12-2

STM4

ATM IOA

OC12/STM4-2 ATM IOA

OC12/STM4 POS IOA

417.0.1ES2-S1

OC12-2

STM4

POS IOA

OC12/STM4-2 POS IOA

OC48/STM16 IOA

437.0.1ES2-S1

OC48

STM16

POS IOA

OC48/STM16 POS IOA

Redundancy IOA

457.0.1ES2-S1

REDUND

IOA

REDUND IOA

Service IOA

467.0.1ES2-S1

SERVICE

IOA

SERVICE IOA

SRP IOA

477.0.1SRP IOASRP IOA

E120 and E320 11.3.x Module Guide

LM-4 Line Module

ES2 4G LM

Module label

•Not applicable

Number of ports

•First supported: 7.0.1

Software release

•176 W maximum

•Acts as frame forwarding engines for the physical interfaces

•Responsible for processing data traffic

•Pairs with IOAs to process data from different types of network connections

Description

•FFA ASIC

Type

•Supports a line rate of 128–byte packets on IOAs

•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular

line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot

2 and slot 4).

•The 320–Gbps switch fabric allocates 10 Gbps of overall bandwidth to each line

module slot. The line interface on the ES2 4G LM when installed in a 320 Gbps

fabric configuration is 3.9 Gbps; you can achieve this rate with random packet sizes

in the range 64–1518 bytes or a mixture of packet sizes that represent Internet mix

traffic (IMIX).

•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for

more information.

Capability

•Not applicable

Software features

•E320 router

•E120 router

Model compatibility

•Not applicable

Line module compatibility

•SRP-100

•SRP-120

•SRP-320

SRP module compatibility

•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

•Can only back up another ES2 4G LM

Line module redundancy

compatibility

•Not applicable

Port redundancy support

•Not applicable

Cables and connectors

When lit, LED indicates:

•OK (green)—Self-test passed

•FAIL (red)—Failure detected

•ONLINE (green)—Online with no alarms or errors

•REDUN (green)—Redundant card available

LEDs

LM-4 Line Module

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,

Managing Modules.

Alarms, errors, and events

E120 and E320 11.3.x Module Guide

LM-10 Uplink Line Module

ES2 10G UPLINK LM

Module label

•Not applicable

Number of ports

•First supported: 7.2.0

Software release

•150 W maximum

•Acts as frame forwarding engines for the physical interfaces

•Processes up to 10 Gb of data traffic

•Pairs with ES2–S2 10GE PR IOA only

•In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)

•If you install the line module in a slot other than slot 2 or slot 4, it will be disabled

•If you install a LM-10 Uplink module next to a configured line module that is already

installed in slot 3 or slot 5, the LM-10 Uplink module will be disabled

•If you install a line module in slot 3 or slot 5 next to a previously installed LM-10

Uplink module, the non-LM-10 Uplink module will be disabled

•In a SRP-120 and SRP-320 configuration, it can be installed in any slot

Description

•IXP network processor

Type

•Supports a line rate of 128–byte frames on IOAs

•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular

line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2

and slot 4).

•The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth

to each line module slot.

•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more

information.

Capability

•Not applicable

Software features

•E320 router

•E120 router

Model compatibility

•Not applicable

Line module compatibility

•SRP-100

•SRP-120

•SRP-320

SRP module compatibility

•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

•Can only back up another ES2 10G UPLINK LM

Line module redundancy

compatibility

•Not applicable

Port redundancy support

•Not applicable

Cables and connectors

LM-10 Uplink Line Module

When lit, LED indicates:

•OK (green)—Self-test passed

•FAIL (red)—Failure detected

•ONLINE (green)—Online with no alarms or errors

•REDUN (green)—Redundant card available

LEDs

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,

Managing Modules.

Alarms, errors, and events

E120 and E320 11.3.x Module Guide

LM-10 Line Module

ES2 10G LM

Module label

•Not applicable

Number of ports

•First supported: 8.0.0

Software release

•198 W maximum

•Acts as frame forwarding engines for the physical interfaces

•Processes up to 10 Gb of data traffic

•Pairs with ES2–S2 10GE PR IOA and ES2–S1 GE-8 IOA

•In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4)

•If you install the line module in a slot other than slot 2 or slot 4, it will be disabled

•If you install the LM-10 module next to a configured line module that is already

installed in slot 3 or slot 5, the LM-10 module will be disabled

•If you install a line module in slot 3 or slot 5 next to a previously installed LM-10

module, the non-LM-10 module will be disabled

•In a SRP-120 and SRP-320 configuration, it can be installed in any slot

Description

•TFA ASIC

Type

•Supports a line rate of 128–byte frames on IOAs

•The 100–Gbps switch fabric allocates 3.4 Gbps of overall bandwidth to each regular

line module slot and 10 Gbps of overall bandwidth to each of the turbo slots (slot 2

and slot 4).

•The 120–Gbps and 320–Gbps switch fabrics allocate 10 Gbps of overall bandwidth

to each line module slot.

•See JunosE System Basics Configuration Guide, Chapter 6, Managing Modules for more

information.

Capability

•Not applicable

Software features

•Not applicable

Line module compatibility

•SRP-100

•SRP-120

•SRP-320

SRP module compatibility

•Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

•Can only back up another ES2 10G LM

Line module redundancy

compatibility

•Not applicable

Port redundancy support

•Not applicable

Cables and connectors

When lit, LED indicates:

•OK (green)—Self-test passed

•FAIL (red)—Failure detected

•ONLINE (green)—Online with no alarms or errors

•REDUN (green)—Redundant card available

LEDs

LM-10 Line Module

•See Monitoring Modules in JunosE System Basics Configuration Guide, Chapter 6,

Managing Modules.

Alarms, errors, and events

E120 and E320 11.3.x Module Guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Juniper Netzwerk-Router Handbücher

Juniper

Juniper SRX240 Series Montageanleitung

Juniper

Juniper EX6210 Bedienungsanleitung

Juniper

Juniper PTX5000 Montageanleitung

Juniper

Juniper NetScreen-5GT Wireless Bedienungsanleitung

Juniper

Juniper J4350 Bedienungsanleitung

Juniper

Juniper ACX2000 Bedienungsanleitung

Juniper

Juniper PTX Series Bedienungsanleitung

Juniper

Juniper T4000 - Bedienungsanleitung

Juniper

Juniper PTX5000 Bedienungsanleitung

Juniper

Juniper JUNOS J Series Bedienungsanleitung

Juniper

Juniper QFX10002 Bedienungsanleitung

Juniper

Juniper QFX5100 Montageanleitung

Juniper

Juniper ACX6160 Bedienungsanleitung

Juniper

Juniper MX2020 Montageanleitung

Juniper

Juniper PTX10001-20C Bedienungsanleitung

Juniper

Juniper ACX1000 Montageanleitung

Juniper

Juniper J-Series Bedienungsanleitung

Juniper

Juniper EX2300 Series Bedienungsanleitung

Juniper

Juniper MX10003 Montageanleitung

Juniper

Juniper PTX10003-80C Montageanleitung

Juniper

Juniper M40 Bedienungsanleitung

Juniper

Juniper ACX2000 Bedienungsanleitung

Juniper

Juniper ACX2000 Montageanleitung

Juniper

Juniper ACX2000 Montageanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise