Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... Bedienungsanleitung

E Series™ Broadband

Services Routers

ERX™ Module Guide

Release

11.3.x

Published: 2010-09-27

This guide provides an overview and description of the line modules (LMs), switch route

processor (SRP) modules, and I/O modules available for the following Juniper Networks

E Series Broadband Services Routers: ERX14xx models, ERX7xx models, and the ERX310

router.

Unless otherwise specified, all line modules pair with I/O modules to create a module

combination. Each module combination provides particular capabilities and connections

in an ERX router.

NOTE: A release may support multiple versions of a module. For information,

see Software Compatibility in JunosE System Basics Configuration Guide,

Chapter 6, Managing Modules.

Table 1 on page 3 lists the module combinations supported by ERX routers.

This book also contains three appendixes:

•Module Protocol Support on page 87

•Module LEDs on page 109

•Module Name Cross-Reference Information on page 115

•Product Reclamation and Recycling Program on page 119

For more information about ERX routers and modules, refer to the following books:

•Modules that have reached end-of-life—E Series End-of-Life Module Guide

•Module installation and maintenance—ERX Hardware Guide

•Managing ERX routers—JunosE System Basics Configuration Guide

•Configuring ERX modules—JunosE Link Layer Configuration Guide

ERX 11.3.x Module Guide

Table 1: ERX Module Combinations

Page

First

JunosE

Support

I/O Module

Label

Line

Module

LabelCombination Name and Type

Fast Ethernet

85.0.0FE-8 I/OGE/FEFE-8 (8 ports) (256-MB memory)

96.0.0FE-8 SFP

I/O

GE/FEFE-8 SFP (8 ports) (256-MB memory)

Gigabit Ethernet (1-port)

115.0.0GE I/O SFPGE/FEGE 1000Base-SX (256-MB memory)

135.0.0GE I/O SFPGE/FEGE 1000Base-LH (256-MB memory)

155.0.0GE I/O SFPGE/FEGE 1000Base-ZX (256-MB memory)

172.0.0GE I/O

MULTI

MODE

GE/FEGE multimode

192.0.0GE I/O

SINGLE

MODE

GE/FEGE single-mode

Gigabit Ethernet (2-port)

215.3.0GE-2 SFP

I/O or

2XGE APS

I/O SFP or

GE-2 APS

I/O SFP

GE-2GE2 1000Base-SX

235.3.0GE-2 SFP

I/O or

2XGE APS

I/O SFP or

GE-2 APS

I/O SFP

GE-2GE2 1000Base-LH

255.3.0GE-2 SFP

I/O or

2XGE APS

I/O SFP or

GE-2 APS

I/O SFP

GE-2GE2 1000Base-ZX

Table 1: ERX Module Combinations (continued)

Page

First

JunosE

Support

I/O Module

Label

Line

Module

LabelCombination Name and Type

GE High Density (HDE)

277.0.0GE-2 SFP

I/O or

2XGE APS

I/O SFP or

GE-2 APS

I/O SFP

GE-HDEGE High Density (2 ports)

297.0.0GE-8 I/OGE-HDEGE High Density (8 ports)

OC3/STM1 ATM

315.0.0, 5.3.0OC3-4 I/O

MULTI

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC3/STM1 ATM multimode without

APS/MSP redundancy (256-MB memory)

335.1.2

5.2.0

(APS/MSP)

4XOC3 APS

I/O

MULTI

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC3/STM1 ATM multimode with APS/MSP

redundancy

355.0.0, 5.3.0OC3-4 I/O

SINGLE

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC3/STM1 ATM single-mode intermediate

reach without APS/MSP redundancy

(256-MB memory)

375.1.2

5.2.0

(APS/MSP)

4XOC3

APS I/O

SINGLE

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC3/STM1 ATM single-mode intermediate

reach with APS/MSP redundancy

395.0.0, 5.3.0OC3-4 I/O

LONG HAUL

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC3/STM1 ATM single-mode long reach

without APS/MSP redundancy (256-MB

memory)

OC3/STM1 GE/FE

416.1.0OC3–2 GE

APS I/O

OC3/STM1

GE/FE

OC3/STM1 GE/FE

OC3/STM1 POS

ERX 11.3.x Module Guide

Table 1: ERX Module Combinations (continued)

Page

First

JunosE

Support

I/O Module

Label

Line

Module

LabelCombination Name and Type

452.0.0OC3-4 I/O

MULTI

MODE

OCx/STMx

POS

OC3/STM1 POS multimode without

APS/MSP redundancy

475.1.2

5.2.0

(APS/MSP)

4XOC3 APS

I/O

MULTI

MODE

OCx/STMx

POS

OC3/STM1 POS multimode with APS/MSP

redundancy

492.0.0OC3-4 I/O

SINGLE

MODE

OCx/STMx

POS

OC3/STM1 POS single-mode intermediate

reach without APS/MSP redundancy

515.1.2

5.2.0

(APS/MSP)

4XOC3 APS

I/O

SINGLE

MODE

OCx/STMx

POS

OC3/STM1 POS single-mode intermediate

reach with APS/MSP redundancy

532.0.0OC3-4 I/O

LONG HAUL

OCx/STMx

POS

OC3/STM1 POS single-mode long reach

OC12/STM4 ATM

555.0.0, 5.3.0OC12 STM4

I/O

MULTI

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC12/STM4 ATM multimode without

APS/MSP redundancy (256-MB memory)

572.0.0 (128

MB)

5.0.0 (256

MB)

OC12 STM4

APS

MULTI

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC12/STM4 ATM multimode with

APS/MSP redundancy

595.0.0, 5.3.0OC12 STM4

I/O

SINGLE

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC12/STM4 ATM single-mode

intermediate reach without APS/MSP

redundancy (256-MB memory)

612.0.0 (128

MB)

5.0.0 (256

MB)

OC12 STM4

APS

SINGLE

MODE

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC12/STM4 ATM single-mode

intermediate reach with APS/MSP

redundancy

Table 1: ERX Module Combinations (continued)

Page

First

JunosE

Support

I/O Module

Label

Line

Module

LabelCombination Name and Type

635.0.0, 5.3.0OC12 STM4

I/O

LONG HAUL

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC12/STM4 ATM single-mode long reach

without APS/MSP redundancy (256-MB

memory)

652.0.0 (128

MB)

5.0.0 (256

MB)

OC12 STM4

APS

LONG HAUL

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

OC12/STM4 ATM single-mode long reach

with APS/MSP redundancy

OC12/STM4 POS

672.0.0OC12 STM4

I/O

MULTI

MODE

OCx/STMx

POS

OC12/STM4 POS multimode without

APS/MSP redundancy

692.0.0OC12 STM4

APS

MULTI

MODE

OCx/STMx

POS

OC12/STM4 POS multimode with

APS/MSP redundancy

712.0.0OC12 STM4

I/O

SINGLE

MODE

OCx/STMx

POS

OC12/STM4 POS single-mode

intermediate reach without APS/MSP

redundancy

732.0.0OC12 STM4

APS

SINGLE

MODE

OCx/STMx

POS

OC12/STM4 POS single-mode

intermediate reach with APS/MSP

redundancy

752.0.0OC12 STM4

I/O

LONG HAUL

OCx/STMx

POS

OC12/STM4 POS single-mode long reach

without APS/MSP redundancy

772.0.0OC12 STM4

APS

LONG HAUL

OCx/STMx

POS

OC12/STM4 POS single-mode long reach

with APS/MSP redundancy

OC48/STM16

794.1.xOC48

FRAME APS

OC48OC48/STM16 POS single-mode short

reach

ERX 11.3.x Module Guide

Table 1: ERX Module Combinations (continued)

Page

First

JunosE

Support

I/O Module

Label

Line

Module

LabelCombination Name and Type

Service Module (SM)

805.1.0No I/O

module

SERVICE

MODULE

SRPs

814.1.3, 5.0.4,

5.1.2, 5.2.0

SRP I/OSRP-5G+SRP-5G+ (1-GB memory)

824.1.3, 5.0.4,

5.1.2, 5.2.0

SRP I/OSRP-10GSRP-10G (2-GB memory)

834.0.0SRP I/OSRP-40G

PLUS

SRP-40G PLUS (2-GB memory)

845.3.0SRP-SE I/OSRP-SE10GSRP-SE10G (1-GB memory)

854.1.0 (128

104 MB)

5.0.0 (256

MB)

4xDS3 ATM

I/O

OCx/STMx

ATM or

OCx/STMx

/DS3-ATM

T3 ATM (4 ports)

FE-8 Module Combination (8 Ports) (256-MB Memory)

GE/FE

Line module label

FE-8 I/O

I/O module label

•8

Number of I/O ports

•First supported: 5.0.0

•Final supported: Not applicable

•The GE/FE line module must have a minimum of 256 MB of memory to be used

with JunosE Release 5.3.0 or a higher-numbered release.

Software release

•130 W

•Fast Ethernet

Description

•EFA ASIC

Type

•IEEE 802.3 standards compliance

•10/100Base-T

Capability

•See “Ethernet Modules” on page 87 for information about the layer 2 and layer

3 protocols and applications that this module combination supports.

Software features

•ERX7xx models

•ERX14xx models

•ERX310 router

Model compatibility

•SRP-5G+

•SRP-10G

•SRP-40G

•SRP-40G PLUS

•SRP-SE10G

SRP module compatibility

•Not applicable

Module redundancy support

•RJ-45 connectors

•For 10-Mbps operation, use CAT 3, 4, or 5 UTP cable.

•For 100-Mbps operation, use only CAT 5 UTP cable.

•The transmitted signal complies with IEEE 802.3/802.3u for cable lengths up

to 100 m (328 feet).

•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors

•See “Module LEDs” on page 109.

LEDs

•See Monitoring Ethernet Interfaces in JunosE Physical Layer Configuration Guide,

Chapter 5, Configuring Ethernet Interfaces.

Alarms, errors, and events

ERX 11.3.x Module Guide

FE-8 SFP Module Combination (8 Ports) (256-MB Memory)

GE/FE

Line module label

FE-8 SFP I/O

I/O module label

•8

Number of I/O ports

•First supported: 6.0.0

•Final supported: Not applicable

Software release

•130 W

•Fast Ethernet

•The FE-8 SFP I/O module uses a range of small form-factor pluggable (SFP)

transceivers to support different modes and cable lengths.

Description

•EFA ASIC

Type

•IEEE 802.3 standards compliance

•100Base-FX

Capability

•See “Ethernet Modules” on page 87 for information about the layer 2 and layer

3 protocols and applications that this module combination supports.

Software features

•ERX7xx models

•ERX14xx models

•ERX310 router

Model compatibility

•SRP-5G+

•SRP-10G

•SRP-40G

•SRP-40G PLUS

•SRP-SE10G

SRP module compatibility

•Not applicable

Module redundancy support

•LC full duplex

•Tx power:

•min: –15 dBm

•max: –8 dBm

•Center wavelength: 1300 nm

•Rx input power:

•min: –28 dBm

•max: –14 dBm

•Rated for 10 km (6.2 miles) over 9-micron core cable

•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (single-mode

fiber)

FE-8 SFP Module Combination (8 Ports) (256-MB Memory)

•LC full duplex

•Tx power: –20 dBm minimum and –14 dBm maximum

•Center wavelength: 850 nm

•Rx input power: –31 dBm minimum and –14 dBm maximum

•Rated for 2 km (1.2 miles) over 62.5/125-micron core cable

•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.

Cables and connectors (multimode

fiber)

•See “Module LEDs” on page 109.

LEDs

•See Monitoring Ethernet Interfaces in JunosE Physical Layer Configuration Guide,

Chapter 5, Configuring Ethernet Interfaces.

Alarms, errors, and events

ERX 11.3.x Module Guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Juniper Netzwerk-Router Handbücher

Juniper

Juniper J-Series Bedienungsanleitung

Juniper

Juniper ACX500 Montageanleitung

Juniper

Juniper MX240 Montageanleitung

Juniper

Juniper PTX1000 Montageanleitung

Juniper

Juniper PTX10001-36MR Bedienungsanleitung

Juniper

Juniper ERX-1410 Bedienungsanleitung

Juniper

Juniper ACX1000 Montageanleitung

Juniper

Juniper PTX5000 Montageanleitung

Juniper

Juniper MX150 Montageanleitung

Juniper

Juniper ACX2200 Bedienungsanleitung

Juniper

Juniper ERX-310 Bedienungsanleitung

Juniper

Juniper J2300 Bedienungsanleitung

Juniper

Juniper PTX3000 Technisches Datenblatt

Juniper

Juniper T1600 Installations- und Betriebshandbuch

Juniper

Juniper T4000 - Montageanleitung

Juniper

Juniper M-Series Bedienungsanleitung

Juniper

Juniper JUNOS OS 10.4 Bedienungsanleitung

Juniper

Juniper MX104 Montageanleitung

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 HARDWARE GUIDE REV... Montageanleitung

Juniper

Juniper EX8208 Bedienungsanleitung

Juniper

Juniper MX150 Bedienungsanleitung

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS - E SERIES END-OF-LIFE MODULE GUIDE... Bedienungsanleitung

Juniper

Juniper QFX10016 Montageanleitung

Juniper

Juniper XRE200 - Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise