Juniper MX960 Bedienungsanleitung

MX960 Ethernet Services Router

Quick Start

18 April 2008

Part Number: 530-021108-01

Revision 2

This document describes how to install the MX960 Ethernet Services Router.

Contents Quick Start Description ...................................................................................3

Step 1: Prepare the Site ...................................................................................4

Rack-Mounting Requirements ...................................................................4

Tools Required ..........................................................................................5

Step 2: Install the Mounting Hardware ............................................................6

Install the Mounting Hardware in a Four-Post Rack or Cabinet .................6

Install the Mounting Hardware in an Open-Frame Rack ............................7

Step 3: Install the Router .................................................................................8

Install the Router Using a Lift ....................................................................8

Install the Router Without a Mechanical Lift ............................................10

Remove Components .......................................................................11

Lift the Router into the Rack .............................................................12

Reinstall Components ......................................................................13

Step 4: Connect External Devices and DPC Cables ........................................13

Connect to a Network for Out-of-Band Management ...............................13

Connect a Management Console .............................................................14

Connect the DPC Cables .........................................................................14

Step 5: Connect Ground and Power Cables ...................................................15

Connect Grounding Cable .......................................................................15

Connect Power to an AC Router ..............................................................15

Connect Power to a DC Router ...............................................................16

Step 6: Perform Initial Software Configuration ..............................................17

Safety Warnings ............................................................................................19

■1

Compliance Statements for NEBS ..................................................................21

Compliance Statements for EMC Requirements ............................................21

Canada ...................................................................................................21

European Union ......................................................................................21

Declaration of Conformity ......................................................................21

List of Technical Publications ........................................................................22

Requesting Technical Support .......................................................................28

Revision History ............................................................................................29

2■

MX960 Ethernet Services Router Quick Start

Quick Start Description

This Quick Start contains information you need to install and configure the router

quickly. For complete installation instructions, see the MX960 Ethernet Services Router

Hardware Guide at http://www.juniper.net/techpubs/.

WARNING: This Quick Start contains a summary of safety warnings in “Safety

Warnings”on page 19. For a complete list of warnings for this router, including

translations, see the MX960 Ethernet Services Router Hardware Guide at

http://www.juniper.net/techpubs/.

The MX960 router is 16 rack units (RU) tall. Three routers can be stacked in a single

floor-to-ceiling rack, for increased port density per unit of floor space. The router

provides 14 slots that can be populated with up to 12 interface cards and two Switch

Control Boards (SCBs) in nonredundant fabric configurations. The MX960 Services

Router is an Ethernet-optimized edge router that provides both switching and

carrier-class Ethernet routing. The MX960 router has a capacity of up to 480 gigabits

per second (Gbps), full duplex.

Fully populated, the MX960 provides up to 480 Gigabit Ethernet or up to 48 10-Gigabit

Ethernet ports. Two types of Dense Port Concentrator (DPC) interface cards are

available, both of which consist of consist of four Packet Forwarding Engines and

enable a throughput of 10 Gbps:

■A 40-port Gigabit Ethernet DPC with SFP connectors (1000 Mbit copper and fiber

only).

■A 4-port 10-Gigabit Ethernet DPC with XFP connectors.

The router is shipped in a cardboard box strapped securely to a wooden pallet. Plastic

straps secure the top and bottom in place. The router chassis is bolted to this pallet.

Quick Start installation instructions and a cardboard accessory box are also included

in the shipping container.

Quick Start Description ■3

Quick Start Description

Step 1: Prepare the Site

Figure 1: Rack Clearance and Router Dimensions

Rack-Mounting Requirements

■You can install the router in a four-post rack or cabinet or an open-frame rack.

■The rack rails must be spaced widely enough to accommodate the router chassis's

external dimensions: 27.75 in. (70.49 cm) high, 23.0 in. (58.42 cm) deep, and

4■Step 1: Prepare the Site

MX960 Ethernet Services Router Quick Start

17.37 in. (44.11 cm) wide. The outer edges of the mounting brackets extend the

width to 19 in. (48.3 cm).

■The rack must be strong enough to support the weight of the fully configured

router, up to 350 lb (158.76 kg). If you stack three fully configured routers in

one rack, it must be capable of supporting about 1,050 lb (476.3 kg).

■For service personnel to remove and install hardware components, there must

be adequate space at the front and back of the router. Allow at least

30 in. (76.2 cm) in front of the router and 24 in. (61 cm) behind the router.

■The rack or cabinet must have an adequate supply of cooling air.

■Ensure that the cabinet allows the chassis hot exhaust air to exit from the cabinet

without recirculating into the router.

■The router must be installed into a rack that is secured to the building structure.

■The router should be mounted at the bottom of the rack if it is the only unit in

the rack.

■When mounting the router in a partially filled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

Tools Required

To unpack the router and prepare for installation, you need the following tools:

■A mechanical lift—recommended

■Phillips (+) screwdrivers, numbers 1 and 2

■2.5 mm flat-blade (–) screwdriver

■3/8-in. nut driver

■1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the

shipping pallet

■Electrostatic discharge wrist strap

■Antistatic mat

Step 1: Prepare the Site ■5

Step 1: Prepare the Site

Step 2: Install the Mounting Hardware

To install the mounting hardware in a four-post rack or cabinet or an open-frame

rack, perform one of the following procedures:

■Install the Mounting Hardware in a Four-Post Rack or Cabinet on page 6

■Install the Mounting Hardware in an Open-Frame Rack on page 7

Install the Mounting Hardware in a Four-Post Rack or Cabinet

To install the mounting shelf, follow this procedure:

1. On the front rack rails, install cage nuts in the holes specified in the MX960

Ethernet Services Router Hardware Guide for the large shelf and the spacer bars.

2. On the front of each front rack rail, partially insert a mounting screw into the

hole containing the lowest cage nut.

3. Install the large shelf on the front rack rails. Rest the bottom slot of each ear on

a mounting screw.

4. Partially insert a mounting screw into the top hole in each ear of the large shelf.

5. Tighten all the screws completely.

6. On the rear rack rails, install cage nuts in the holes specified in the MX960

Ethernet Services Router Hardware Guide for the small shelf.

7. On the back of each rear rack rail, partially insert a mounting screw into the hole

containing the lowest cage nut.

8. Install the small shelf on the back rack rails. Rest the bottom slot of each ear on

a mounting screw. The small shelf installs on the back of the rear rails, extending

toward the center of the rack. The bottom of the small shelf should align with

the bottom of the large shelf.

9. Partially insert screws into the open holes in the ears of the small shelf.

10. Tighten all the screws completely.

6■Step 2: Install the Mounting Hardware

MX960 Ethernet Services Router Quick Start

Figure 2: Mount Hardware for a Four-Post Rack or Cabinet

Install the Mounting Hardware in an Open-Frame Rack

To install the mounting shelf, follow this procedure:

1. On the rear of each rack rail, partially insert a mounting screw into the highest

hole specified in the MX960 Ethernet Services Router Hardware Guide for the large

shelf.

2. Install the large shelf on the rack. Hang the shelf over the mounting screws using

the keyhole slots located near the top of the large shelf flanges.

3. Partially insert screws into the open holes in the ears of the large shelf.

4. Tighten all the screws completely.

Step 2: Install the Mounting Hardware ■7

Step 2: Install the Mounting Hardware

Figure 3: Mount Hardware for an Open-Frame Rack

Step 3: Install the Router

Because of the router's size and weight, we recommend you install the router using

a mechanical lift. The procedure for installing the router depends on whether you

use a mechanical lift:

■Install the Router Using a Lift on page 8

■Install the Router Without a Mechanical Lift on page 10

Install the Router Using a Lift

To install the router using a lift:

1. Ensure the rack is in its permanent location and is secured to the building. Ensure

that the installation site allows adequate clearance for both airflow and

maintenance. For details, see the MX960 Ethernet Services Router Hardware Guide.

2. Load the router onto the lift, making sure it rests securely on the lift platform

(see Figure 4 on page 9).

8■Step 3: Install the Router

MX960 Ethernet Services Router Quick Start

Figure 4: Load the Router onto the Lift

3. Using the lift, position the router in front of the rack or cabinet, centering it in

front of the mounting shelves.

4. Lift the chassis approximately 0.75 in. above the surface of the mounting shelves

and position it as close as possible to the shelves.

5. Carefully slide the router onto the mounting shelves so that the bottom of the

chassis and the mounting shelves overlap by approximately two inches.

6. Slide the router onto the mounting shelves until the mounting brackets or

front-mounting flanges contact the rack rails. The shelves ensure that the holes

in the mounting brackets and the front-mounting flanges of the chassis align

with the holes in the rack rails.

7. Move the lift away from the rack.

8. To install the router in an open-frame rack, install a mounting screw into each

of the open mounting holes aligned with the rack, starting from the bottom.

9. Visually inspect the alignment of the router. If the router is installed properly in

the rack, all the mounting screws on one side of the rack should be aligned with

the mounting screws on the opposite side and the router should be level.

Step 3: Install the Router ■9

Step 3: Install the Router

Install the Router Without a Mechanical Lift

To install the router without a mechanical lift, perform all of the following procedures:

■Remove Components on page 11

■Lift the Router into the Rack on page 12

■Reinstall Components on page 13

Figure 5: Components to Remove from the Front of the Router

g004091

Figure 6: Components to Remove from the Rear of the Router

10 ■Step 3: Install the Router

MX960 Ethernet Services Router Quick Start

Andere Handbücher für MX960

Inhaltsverzeichnis

Andere Juniper Netzwerk-Router Handbücher

Juniper

Juniper T1600 Bedienungsanleitung

Juniper

Juniper ACX Series Bedienungsanleitung

Juniper

Juniper EX9200 Series Technisches Datenblatt

Juniper

Juniper JRR200 Montageanleitung

Juniper

Juniper T4000 - Montageanleitung

Juniper

Juniper PTX10001-20C Bedienungsanleitung

Juniper

Juniper PTX1000 Montageanleitung

Juniper

Juniper ACX5448 Bedienungsanleitung

Juniper

Juniper JCS 1200 Bedienungsanleitung

Juniper

Juniper MX204 Montageanleitung

Juniper

Juniper SRX240 Series Montageanleitung

Juniper

Juniper ACX2000 Montageanleitung

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 HARDWARE GUIDE REV... Montageanleitung

Juniper

Juniper PTX10002-60C Bedienungsanleitung

Juniper

Juniper MX2020 Montageanleitung

Juniper

Juniper PTX5000 Bedienungsanleitung

Juniper

Juniper EX9200 Series Technisches Datenblatt

Juniper

Juniper ERX-1410 Bedienungsanleitung

Juniper

Juniper M120 Bedienungsanleitung

Juniper

Juniper T640 Montageanleitung

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 MODULE GUIDE REV... Bedienungsanleitung

Juniper

Juniper QFabric QFX5100-24Q Bedienungsanleitung

Juniper

Juniper ACX500 Bedienungsanleitung

Juniper

Juniper T320 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise