JVA Z Series Bedienungsanleitung
JVA TECHNOLOGIES
www.jva-fence.com
User ManUal
Page 2 © JVA Technologies www.jva-fence.com
1 Quick Start Guide
1.1 THE FULL USER MANUAL
The compete user manuals can be downloaded here:
www.jva-fence.com/z11
www.jva-fence.com/z13
www.jva-fence.com/z14
www.jva-fence.com/z18
1.2 LOW VOLTAGE WIRING
Label Type Descripon
IN1 2 Way Energizer control input 1 (dry contact) internally wired
in parallel with the key switch. Arm energizer when
closed
GATE 2 Way Energizer control input 2 (dry contact). Default func-
on is gate input, normally closed. When the unit is
armed and the gate is opened, it will trigger the gate
alarm.
KEYPAD 3 Way Supplies power and data line for an external keypad.
The +12 source on these terminals is protected with
1A self reseng fuse.
SIREN 2 Way Switched 12V output. 30W max, shared between Si-
ren and Strobe. Low side switched
STROBE 2 Way Switched 12V output. 30W max, shared between Si-
ren and Strobe. Low side switched
Page 3
© JVA Technologies www.jva-fence.com Z Series Quick Start Manual
Label Type Descripon
16Vac 3 Way 16Vac 1.5A power input plus earth. Connecon of
the earth is only required where local safety or wir-
ing codes demand it. This should be connected to the
cabinet or mains earth NOT the fence earth.
Ba Battery
leads
12V dc or baery connecon via F1
(4 Amp slow blow fuse).
Relay 3 3 Way “Form C” relay with dry contacts. Default operaon
Fence Alarm
Relay 4 3 Way “Form C” relay with dry contacts. Default operaon
Zone Armed
Relay 5 3 Way “Form C” relay with dry contacts. Default operaon
General Alarm
1.3 JUMPERS
Jumpers allow you to turn on and o dierent features, or reset the device
to defaults.
JUMPER FUNCTION
J3 Inhibit AC fail error.
J3(Z14R) Tamper disable.
J4 Factory default jumper - on for normal operaon.
O to return programmable opons to factory defaults on
power up.
J8 Disable on board beeper
J5, J6 & J7 Supplies +12V to the Common terminal of Relay 3, 4, 5.
Jumpers located on the top right hand side of the board
Page 4 © JVA Technologies www.jva-fence.com
1.4 QUICK TEST OF CONFIGURED UNIT
It is a good idea to test the energizer before connecng the it to a fence.
This will give you condence that the unit is operang as expected and it
also isolates potenal fence issues.
To do this, connect your energizer with a “test fence” as shown.
Power the energizer and then Arm it. The unit should begin pulsing and
not show any alarms. Disarm the energizer and remove the fence cable as
shown.
Arm the energizer once again, aer 3 pulses (unless you congured it oth-
erwise) the unit should go into alarm as the fence will appear to be cut.
Check that any sirens, strobes or relays acvate as expected.
Page 5
© JVA Technologies www.jva-fence.com Z Series Quick Start Manual
1.5 CONNECTING TO THE FENCE
A convenonal fence installaon including earth loop monitoring.
Page 6 © JVA Technologies.
Z-Series Quick Start Manual
1.6 CHANGING THE PROGRAMMING OPTIONS
Default Installer PIN 012345
Default User PIN 1234
First you have to enter Programming mode.
Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9
Enter Programming Mode Installer Pin * 0 #
When you have entered Programming mode you can begin to enter the following opons to congure your Security
Energizer. Default Values are highlighted in grey.
Command Key1 Key2 Keys 3 and 4 Key5
Change The Installer
PIN 6 Digits
0 0 Enter the new 6 digit Installer PIN #
High Power Mode
Power Level
0 1 Enter the value in Hundreds of Volts #
Example: to set 8.2kV, use 82 for keys 3 and 4. Default is 85 (8.5kV)
Low Power Mode
Power Level
0 2 Enter the value in Hundreds of Volts #
Example: to set 1.3kV, use 13 for keys 3 and 4. Default is 11 (1.1kV)
Z-Series Quick Start Manual Page 7
Command Key1 Key2 Keys 3 and 4 Key5
Return Fence Alarm
Voltage For High
Power Mode
0 3 Enter the value in Hundreds of Volts #
Example: to set 3.8kV, use 38 for keys 3 and 4. Default is 40 (4.0kV)
Return Fence Alarm
Voltage For Low
Power Mode
0 5 Enter the value in Hundreds of Volts #
Example: to set 0.8V, use 08 for keys 3 and 4. Default is 05 0.5kV)
Bad/Missed Pulse
Count Before Alarm
Triggers
0 6 Enter the number of Missed Pulses #
Example: to set 14 counts, use 14 for keys 3 and 4. Default is 03
Baery Alarm Volt-
age (olts). Alarm Val-
ue Shown, Reduced
Power is 1V less
0700 01 02 03 04 05 06 07 08 09 #
9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5
Siren On Time
(S=Seconds,
M=Minutes)
0 8 00 01 02 03 04 05 06 07 08 09 #
10S 30S 1M 2M 3M 4M 5M 20M 45M 130M
Siren O Time
(S=Seconds,
M=Minutes)
0 9 00 01 02 03 04 05 06 07 08 09 #
10S 1M 2M 5M 10M 20M 30M 40M 50M 60M
Siren Cycles 1 0 00 01 02 03 04 05 06 07 08 09 #
012345678 9
Page 8 © JVA Technologies.
Z-Series Quick Start Manual
Command Key1 Key2 Keys 3 and 4 Key5
Gate Entry/Exit
Delay (S=Seconds,
M=Minutes)
1 3 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M 8M
Chime Mode 1 4 01 02 03 04 05 #
None Door Chime Siren Fence
Alarm
Gate Beeps
Plus Siren
Combined Opons 1
(add up the opons
you want. e.g. for
Max Power and Limit
output:
2 + 4 = 6 Therefore
enter 06 for keys 3
and 4
1 6 +2 +4 +8 +16 +32 #
Maximum
Power at all
mes
Limits out-
put to 2.5J
per Zone
Enables IR
Tamper.
Stop slaves
on comms
fail
Stop Ener-
gizer send-
ing alarm
memory
An Bridging
Threshold
17 Enter in the percentage dierence required to trigger the An-
Bridging alarm. e.g. if you require a 10% change in return voltage to
trigger the alarm, enter 10 for keys 3 and 4. Default is 00 (Disabled)
#
Z-Series Quick Start Manual Page 9
Command Key1 Key2 Keys 3 and 4 Key5
Combined Opons 2
(like Combined
Opons 1)
1 8 +1 +2 +4 +8 +16 +32 +64 +128 #
Siren
Chirp
on
Arm
Enable
Entry
Exit
Gate
4800
Baud
9600
Baud
Low
Power
to Bite
Bite to
Low
Power
Auto Re-arm Time
S=Seconds, M = Min-
utes, D=Disabled
2 0 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M D
Relay 1 2 1 Opons Explained under “1.6.1 Relay Funcons” Default is 08 #
Relay 2 2 2 Opons Explained under “1.6.1 Relay Funcons” Default is 09 #
Relay 3 (Z14R only) 2 3 Opons Explained under “1.6.1 Relay Funcons” Default is 00 #
Relay 4 (Z14R only) 2 4 Opons Explained under “1.6.1 Relay Funcons” Default is 02 #
Relay 5 (Z14R only) 2 5 Opons Explained under “1.6.1 Relay Funcons” Default is 07 #
Group Mode 2 6 00 01 02 etc 15 #
No Group Master Slave 1 Slave 14
Input 1 27 Opons Explained under “1.6.2 Input Funcons” Default is (Momen-
tary Arm)
#
Input 2 2 8 Opons Explained under “1.6.2 Input Funcons” Default is 06 (N/O
Gate 1)
#
Page 10 © JVA Technologies.
Z-Series Quick Start Manual
Command Key1 Key2 Keys 3 and 4 Key5
Exit Programming
Mode
* #
1.6.1 Relay Funcons
The table below is for use for the relay programming opons menoned in the table on the previous page.
Keys 3
and 4
Funcon Descripon
00 Fence Triggers when Zone 1 is Armed and Return Voltage is below the Threshold Voltage
01 Fence or O Triggers when Zone 1 is Disarmed or Return Voltage is below the Threshold Voltage
02 Armed Zone 1 is Armed
06 Fence Bi-Polar Triggers when energizer is Armed and the fence Return Voltage on either Bi-Polar re-
turn line has fallen below the Threshold Voltage
07 General Triggers on AC Fail, Tamper, Low Baery/Bad Baery, Gate Alarm or Internal error.
Latched (internal errors only)
08 Siren Triggers on Fence Alarm, Gate or Tamper. Will me out aer the Siren Time Out me.
Latched
09 Strobe Triggers on Fence alarm, Gate or Tamper. Only turns o on Energizer Disarm. Latched
10 AC Fail Triggers on AC Fail
11 Low/Bad Battery Triggers on Low or Bad Battery
12 Tamper Triggers when the case has been opened and J3 has been tted (Z14R only)
Andere Handbücher für Z Series
2
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere JVA Stromversorgung Handbücher
JVA
JVA Z11 Bedienungsanleitung
JVA
JVA Z Series Benutzerhandbuch
JVA
JVA M1.5 Bedienungsanleitung
JVA
JVA MB8 Bedienungsanleitung
JVA
JVA PET Series Bedienungsanleitung
JVA
JVA SV2 Handbuch
JVA
JVA MB8 Bedienungsanleitung
JVA
JVA RSG1 Bedienungsanleitung
JVA
JVA MB1.5 Bedienungsanleitung
JVA
JVA Z Series Bedienungsanleitung
JVA
JVA Wi-Fi Anywhere PTE2700 Bedienungsanleitung
JVA
JVA Wi-Fi Anywhere PTE2704 Bedienungsanleitung
JVA
JVA Wi-Fi Anywhere WA20M Bedienungsanleitung
JVA
JVA IP Energizer MB 16 Bedienungsanleitung
JVA
JVA Z28 Bedienungsanleitung
JVA
JVA Z28 Bedienungsanleitung
JVA
JVA M1.5 Bedienungsanleitung
JVA
JVA Z28 Bedienungsanleitung
JVA
JVA Z14 Bedienungsanleitung
JVA
JVA Z114 Bedienungsanleitung
