JVA Z28 Bedienungsanleitung

JVA TECHNOLOGIES

www.jva-fence.com

Z28 User ManUal

Page 6 © JVA Technologies Pty. Ltd.

Quick Start Guide

JVA Z28 Manual

1 QUICK START GUIDE

1.1 CHANGING THE PROGRAMMING OPTIONS

Default Installer PIN 012345

Default User PIN 1234

First you have to enter Programming mode.

Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9

Enter Programming Mode Installer Pin * 0 #

When you have entered Programming mode you can begin to enter the following opons to congure your Z28 Se-

curity Energizer. Default Values are highlighted in grey.

Command Key1 Key2 Keys 3 and 4 Key5

Change the Installer

PIN 6 Digits

0 0 Enter the new 6 digit Installer PIN #

High Power Mode

Power Level

0 1 Enter the value in Hundreds of Volts #

Example: to set 8.2kV, use 82 for keys 3 and 4. Default is 85 (8.5kV)

Low Power Mode

Power Level

0 2 Enter the value in Hundreds of Volts #

Example: to set 1.3kV, use 13 for keys 3 and 4. Default is 11 (1.1kV)

Quick Start Guide

JVA Z28 Manual Page 7

Command Key1 Key2 Keys 3 and 4 Key5

Return 1 Fence

Alarm Voltage For

High Power Mode

0 3 Enter the value in Hundreds of Volts #

Example: to set 3.8kV, use 38 for keys 3 and 4. Default is 40 (4.0kV)

Return 2 Fence

Alarm Voltage For

High Power Mode

0 4 Enter the value in Hundreds of Volts #

Example: to set 3.8kV, use 38 for keys 3 and 4. Default is 40 (4.0kV)

Return Fence Alarm

Voltage For Low

Power Mode

0 5 Enter the value in Hundreds of Volts #

Example: to set 0.8kV, use 08 for keys 3 and 4. Default is 05 0.5kV)

Bad/Missed Pulse

Count Before Alarm

Triggers

0 6 Enter the number of Missed Pulses #

Example: to set 14 counts, use 14 for keys 3 and 4. Default is 03

Baery Alarm

Voltage (Volts).

Alarm Value Shown,

Reduced Power is

1V less

0 7 00 01 02 03 04 05 06 07 08 09 #

9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5

Siren On Time

(S=Seconds,

M=Minutes)

0 8 00 01 02 03 04 05 06 07 08 09 #

10S 30S 1M 2M 3M 4M 5M 20M 45M 130M

JVA Z28 Manual

Quick Start Guide

Page 8 © JVA Technologies Pty. Ltd. www.jva-fence.com

Command Key1 Key2 Keys 3 and 4 Key5

Siren O Time

(S=Seconds,

M=Minutes)

0 9 00 01 02 03 04 05 06 07 08 09 #

10S 1M 2M 5M 10M 20M 30M 40M 50M 60M

Siren Cycles 1 0 00 01 02 03 04 05 06 07 08 09 #

012345678 9

Gate Entry/Exit

Delay (S=Seconds,

M=Minutes)

1 3 00 01 02 03 04 05 06 07 08 09 #

0S 30S 1M 2M 3M 4M 5M 6M 7M 8M

Chime Mode 1 4 00 01 02 03 04 #

None Door Chime Siren Fence

Alarm

Gate Beeps

Plus Siren

Combined Opons 1

(Add up the op-

ons you want.

E.g. for Max Power

and Limit output:

2 + 4 = 6 Therefore en-

ter 06 for keys 3 and 4

+1 +2 +4 +8 +16 +32 +64 +128 #

N/A Max

Power

2.5J

limit per

zone

N/A Disarm

comms

fail

Stop

sending

alarm

memory

Ignore

Low

Baery

Alarm

N/A

An Bridging

Threshold

1 7 Enter in the percentage dierence required to trigger the An-Bridg-

ing alarm. e.g. if you require a 10% change in return voltage to trigger

the alarm, enter 10 for keys 3 and 4. Default is 00 (Disabled)

Quick Start Guide

JVA Z28 Manual Page 9

Command Key1 Key2 Keys 3 and 4 Key5

Combined Opons 2

(Like Combined

Opons 1)

1 8 +1 +2 +4 +8 +16 +32 +64 +128 #

Siren

Chirp on

Arm

Enable

Entry

Exit

Gate

4800

Baud

9600

Baud

N/A N/A N/A N/A

Auto Re-arm Time

S=Seconds, M =

Min, D=Disabled

2 0 00 01 02 03 04 05 06 07 08 09 #

0S 30S 1M 2M 3M 4M 5M 6M 7M D

Relay 1 2 1 Explained under “1.1.1 Relay Funcons” Default is 09 (Strobe 1) #

Relay 2 2 2 Explained under “1.1.1 Relay Funcons” Default is 13 (Strobe 2) #

Relay 3 2 3 Explained under “1.1.1 Relay Funcons” Default is 08 (Siren) #

Group Mode 2 6 00 01 02 Etc 15 #

No Group Master Slave 1 Slave 14

Input 1 2 7 Default is 00 (N/O Arm/Disarm). See “1.1.2 Input Funcons” #

Input 2 2 8 Default is 16 (N/C Gate 1). See “1.1.2 Input Funcons” #

Input 3 2 9 Default is 17 (N/C Gate 2). See “1.1.2 Input Funcons” #

Exit Programming

Mode

* #

Page 10 © JVA Technologies Pty. Ltd.

Quick Start Guide

JVA Z28 Manual

1.1.1 Relay Funcons

The table below is for use for the relay programming opons menoned in the table on the previous page.

Keys 3

and 4

Funcon Descripon

00 Fence 1 Triggers when Zone 1 is Armed and Return Voltage is below the Threshold Voltage

01 Fence 1 or O Triggers when Zone 1 is Disarmed or Return Voltage is below the Threshold Voltage

02 Armed 1 Zone 1 is Armed

03 Fence 2 Triggers when Zone 2 is Armed and Return Voltage is below the Threshold Voltage

04 Fence 2 or O Triggers when Zone 2 is Disarmed or Return Voltage is below the Threshold Voltage

05 Armed 2 Zone 2 is Armed

07 General Triggers on AC Fail, Tamper, Low Baery/Bad Baery, Gate Alarm or Internal error.

Latched (internal errors only)

08 Siren Triggers on Fence Alarm, Gate or Tamper. Will me out aer the Siren Time Out me.

Latched

09 Strobe Triggers on Fence alarm, Gate or Tamper. Only turns o on Energizer Disarm. Latched

10 AC Fail Triggers on AC Fail

11 Low/Bad Bat-

tery

Triggers on Low or Bad Baery

12 Tamper Triggers when the Tamper Input (if congured) is triggered

14 Gate 1 or 2 Triggers on a Gate Alarm

Quick Start Guide

JVA Z28 Manual Page 11

Keys 3

and 4

Funcon Descripon

15 Siren Caused by

Gate

Behaves like siren, only for Gate Alarms

16 Armed - Low

Power Mode

Triggers when Armed in Low Power mode

17 Group Armed Triggers when group is Armed. Only congurable on group master.

18 Group general Triggers on group general Alarm. Only congurable on group master.

20 Host Control This Relay is completely controlled from a Host system such as Perimeter Patrol or a

Keypad. If the Host system is disconnected from the Energizer for more than 30 sec-

onds, the Relay will automacally change to the Alarm State

21 Host Control -

Not Fail Safe

This Relay is completely controlled from a Host system such as Perimeter Patrol or a

Keypad. If the Host system is disconnected then the Relay will maintain its current state

unl the Host re-connects and requests the relay to change state.

Page 12 © JVA Technologies Pty. Ltd.

Quick Start Guide

JVA Z28 Manual

1.1.2 Input Funcons

Key3 Input Trigger Key4 Input Funcon

0Normally Open (Acve when Closed) 0Arm All Zones when Acve / Disarm otherwise

1Normally Closed (Acve when Open) 1Arm Zone 1 when Acve / Disarm otherwise

2 Momentary Toggle (Toggle between states) 2 Arm Zone 2 when Acve / Disarm otherwise

3NO Pulse Extend (Extend a short Close signal by 3

seconds)

3Low Power when Acve / High Power otherwise.

Requires Energizer to be Armed

4NC Pulse Extend (Extend a short Open signal by 3

seconds)

4Low Power Zone 1 when Acve / High Power

otherwise. Requires Energizer to be Armed

5Low Power Zone 2 when Acve / High Power

otherwise. Requires Energizer to be Armed

6Gate 1 is Open when Acve / Closed otherwise

7Gate 2 is Open when Acve / Closed otherwise

8Tamper Alarm triggered when Acve

9 Pass Through input signal to other device

Quick Start Guide

JVA Z28 Manual Page 13

1.2 SUMMARY OF KEYPAD FUNCTIONS

Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9 Key10

Arm/Disarm USER PIN #

Silence the Energizer Siren 1 4 7 0 #

Enter Programming Mode INSTALLER PIN * 0 #

Enter Keypad Programming Mode INSTALLER PIN * 0 1 #

Exit Programming (Any Mode) * #

Change a User PIN, 4 Digits USER PIN * 0 # [New

PIN]

Arm All Zones (Mul-Zone Groups) USER PIN * 1 0 #

Arm Specic Zone (up to Zone 15) USER PIN * 1 Zone Number #

Disarm All Zones USER PIN * 2 0 #

Disarm Specic Zone (up to Zone 15) USER PIN * 2 Zone Number #

Switch to Low Power Mode (All Zones) USER PIN * 4 1 #

Switch Specic Zone to Low Power USER PIN * 4 1 Zone Number #

Switch to High Power Mode (All Zones) USER PIN * 4 2 #

Switch Specic Zone to High Power USER PIN * 4 2 Zone Number #

Arm Gate Zone only USER PIN * 4 #

Bypass Siren (All Zones) USER PIN * 5 2 #

Bypass Specic Zone Siren USER PIN * 5 2 Zone Number #

Quick Start Guide

JVA Z28 Manual

Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9 Key10

Re-enable Siren USER PIN * 5 1 #

Re-enable Specic Zone Siren USER PIN * 5 1 Zone Number #

Bypass Gate Alarm (All Zones) USER PIN * 5 4 #

Bypass Specic Gate Alarm USER PIN * 5 4 Zone Number #

Re-enable Gate Alarm (All Zones) USER PIN * 5 3 #

Re-enable Specic Gate Alarm USER PIN * 5 3 Zone Number #

Arm in Agricultural Mode (No Alarms) USER PIN * 9 Zone Number

Reset and Display Firmware Version USER PIN * 6 8 #

Reset and Return to Factory Defaults INSTALLER PIN * 6 8 #

Andere Handbücher für Z28

Inhaltsverzeichnis

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung