JVC KD-DV4506 Leitfaden

KD-DV4506/KD-DV4505/

KD-DV4504

Installation/Connection Manual

GET0588-008B

[A/UI]

0409DTSMDTJEIN

WARNINGS

• DO NOT install any unit or wire any cable in a location where;

– it may obstruct the steering wheel and gearshift lever operations.

– it may obstruct the operation of safety devices such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving.

• If you need to operate the unit while driving, be sure to look around carefully.

• The driver must not watch the monitor while driving.

If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown.

– This warning appears only when the parking brake lead is connected to the parking brake system built in the car.

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ωto 8 Ω).

If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 26 of the INSTRUCTIONS).

• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

Heat sink

Rubber cushion

Washer (ø5)

Lock nut (M5)

Mounting bolt (M5 ×20 mm)

Parts list for installation and connection

If any item is missing, consult your JVC car audio dealer immediately.

Handles

A/ B

Hard case/Control panel

Sleeve

Trim plate

Power cord

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

Remote controller/Battery

Instal1-2_DV4506_008B_ff.indd 1Instal1-2_DV4506_008B_ff.indd 1 4/21/09 2:14:11 PM4/21/09 2:14:11 PM

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Removing the unit

Before removing the unit, release the rear section.

Do the required electrical connections.

Bend the appropriate tabs to hold the

sleeve firmly in place.

*1When you stand the unit, be careful not to damage the fuse on the rear.

*2Not supplied for this unit.

When installing the unit without using the sleeve

In a Toyota car for example, first remove the car radio and install the unit in its place.

When using the optional stay

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws

are used, they could damage the unit.

Install the unit at an angle of less than 30˚.

TROUBLESHOOTING

•The fuse blows.

*Are the red and black leads connected correctly?

•Power cannot be turned on.

*Is the yellow lead connected?

•No sound from the speakers.

*Is the speaker output lead short-circuited?

•Sound is distorted.

*Is the speaker output lead grounded?

*Are the “–” terminals of L and R speakers grounded in common?

•Noise interfere with sounds.

*Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

•This unit becomes hot.

*Is the speaker output lead grounded?

*Are the “–” terminals of L and R speakers grounded in common?

•This unit does not work at all.

*Have you reset your unit?

Screw (option)

Stay (option)

Fire wall

Dashboard

Bracket *2

Flat head screws (M5 ×8 mm) *2

Pocket

Flat head screws (M5 ×8 mm) *2

Bracket *2

Insert the two handles, then

pull them as illustrated so

that the unit can be removed.

Instal1-2_DV4506_008A_f.indd 2Instal1-2_DV4506_008A_f.indd 2 11/9/08 11:06:33 AM11/9/08 11:06:33 AM

Connecting the parking brake wire (When installing the monitor in a location where it can be seen by the driver)

Connect the parking brake wire to the parking brake system built in the car.

Connect the parking brake wire to metallic body or chassis of the car.

Parking brake wire (light green)

To metallic body or chassis of the car

Parking brake switch (inside the car)

Parking brake

Parking brake wire (light green)

To external components (see diagram )

Light green

VIDEO OUT (see diagram )

DIGITAL OUT

(see diagram )

(see diagram , )

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.

The leads of the power cord and those of the connector from the car body may be different in color.

1Connect the colored leads of the power cord in the order specified in the illustration below.

2Connect the antenna cord.

3Finally connect the wiring harness to the unit.

15 A fuse

Black

Blue with white stripe

Red

Yellow *2

To metallic body or chassis of the car

Ignition switch

Fuse block

To an accessory terminal in the fuse block

To the remote lead of other equipment (200 mA max.)

To a live terminal in the fuse block connecting to the car battery

(bypassing the ignition switch) (constant 12 V)

*1Not supplied for this unit.

*2Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

LINE OUT (see diagram )

Rear ground terminal

Left speaker (front) Right speaker (front) Left speaker (rear) Right speaker (rear)

PurplePurple with black stripeGreenGreen with black stripeGrayGray with black stripeWhiteWhite with black stripe

Typical connections

ELECTRICAL CONNECTIONS

Antenna terminal

To the automatic antenna if any (250 mA max.)

Blue

Connecting the parking brake wire (When installing the monitor in a location where it cannot be seen by the driver)

Crimp connector *1

Instal3-4_DV4506_008B_ff.indd 3Instal3-4_DV4506_008B_ff.indd 3 4/21/09 12:50:01 PM4/21/09 12:50:01 PM

When connecting the external components, refer also to the manuals supplied for the components and

adapters.

CAUTION:

Before connecting the external components, make sure that the unit is turned off.

You can connect the following JVC components to the CD changer jack.

JVC component Model name

CD changer (CD-CH) CH-X1500, etc.

You can also connect the following components through the various JVC adapters.

• Connection cords may need to be purchased separately.

Component Adapter Model name

iPod Interface adapter for iPod KS-PD100

Portable audio player with line

output jacks

Line input adapter KS-U57

Portable audio player with 3.5 mm

stereo mini jack

AUX input adapter KS-U58

EConnecting the external amplifier

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.

Rear speakers

JVC Amplifier

Remote lead Y-connector *3

Remote lead (blue with white stripe)

To the remote lead of other equipment or automatic antenna if any

Front speakers

Required connections for DVD playback

Audio/video control amplifier or the decoder compatible with the

multichannel digital sources

KV-MR9010

9-INCH WIDESCREEN MONITOR *3

Digital optical cable *3

Video cord *3

*3Not supplied for this unit.

*4Signal cord (not supplied for this unit).

*5Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.