JVC KD-R728BT Bedienungsanleitung

ENGLISH

ESPAÑOL

FRANÇAIS

GET0709-001B

[J]

EN, SP, FR

KD-R728BT

CD RECEIVER / RECEPTOR CON CD /

RÉCEPTEUR CD

For canceling the display demonstration, see page 4. / Para cancelar la demostración en pantalla,

consulte la página 4. / Pour annuler la démonstration des affichages, référez-vous à la page 4.

For customer Use:

Enter below the Model

No. and Serial No. which

are located on the top or

bottom of the cabinet.

Retain this information

for future reference.

Model No.

Serial No.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Still having trouble??

USA ONLY

Call 1-800-252-5722

http://www.jvc.com

We can help you!

• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to

connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to

meet Apple performance standards. Apple is not responsible for the operation of this device or

its compliance with safety and regulatory standards. Please note that the use of this accessory

with iPod, or iPhone may affect wireless performance.

• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

• PANDORA® internet radio is a registered trademark of Pandora Media, Inc.

CoverRear_KD-R728[J]ff.indd 1-2CoverRear_KD-R728[J]ff.indd 1-2 1/24/11 5:05:06 PM1/24/11 5:05:06 PM

2ENGLISH

[European Union only]

Caution:

Adjust the volume so that you can hear sounds

outside the car. Driving with the volume too

high may cause an accident.

WARNING:

Stop the car before operating the unit.

Caution on volume setting:

Digital devices (CD/USB) produce very little

noise compared with other sources. Lower the

volume before playing these digital sources to

avoid damaging the speakers by the sudden

increase of the output level.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

Caution:

Changes or modifications not approved by JVC could void the user’s authority to operate the

equipment.

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave

all servicing to qualified service personnel.

3.CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare

into beam.

(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not

view directly with optical instruments.

4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and

to obtain the best possible performance from the unit.

EN02-29_KD-R728BT[J]_f.indd 2EN02-29_KD-R728BT[J]_f.indd 2 1/12/11 4:47:37 PM1/12/11 4:47:37 PM

3ENGLISH

How to attach/detach the control

panel

How to reset your unit

Your preset adjustments will

also be erased.

How to forcibly eject a disc

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

Maintenance

Cleaning the unit

Wipe off the dirt on the panel with a dry silicon

or soft cloth. Failure to observe this precaution

may result in damage to the unit.

Cleaning the connector

Wipe off dirt on the connector of the unit and

panel. Use a cotton swab or cloth.

Caution for DualDisc playback:

The Non-DVD side of a “DualDisc” does not

comply with the “Compact Disc Digital Audio”

standard. Therefore, the use of Non-DVD side

of a DualDisc on this product may not be

recommended.

JVC bears no responsibility for any loss of data

in an iPod/iPhone and/or USB mass storage

class device while using this System.

CONTENTS

3 How to attach/detach the control

panel

3 How to reset your unit

3 How to forcibly eject a disc

3 Maintenance

4 Canceling the display

demonstration

4 Setting the clock

5 Preparing the remote controller

5 About discs

6 Basic operations

7 Listening to the radio

8 Listening to a disc

10 Listening to a USB device

11 Using Bluetooth® devices

12 Connecting a Bluetooth device

13 Using a Bluetooth mobile phone

16 Using a Bluetooth audio player

17 Changing the Bluetooth settings

18 Listening to an iPod/iPhone

21 Listening to the other external

components

22 Selecting a preset sound mode

23 Menu operations

26 Troubleshooting

29 Specifications

Condensation : When the car is air-

conditioned, moisture may collect on the

laser lens. This may cause disc read errors. In

this case, remove the disc and wait for the

moisture to evaporate.

Temperature inside the car : If you have

parked the car for a long time in hot or cold

weather, wait until the temperature in the car

becomes normal before operating the unit.

[Hold]

EN02-29_KD-R728BT[J]_f.indd 3EN02-29_KD-R728BT[J]_f.indd 3 1/12/11 4:47:38 PM1/12/11 4:47:38 PM

4ENGLISH

1 Turn on the power.

Setting the clock

1 Turn on the power.

3 Select <CLOCK>.

4 Select <CLOCK SET>.

5 Adjust the hour.

6 Adjust the minute.

7 Finish the procedure.

4 Select <DEMO OFF>.

6 Finish the procedure.

Canceling the display demonstration

(Initial setting)

[Hold]

(Initial setting)

[Hold]

EN02-29_KD-R728BT[J]_f.indd 4EN02-29_KD-R728BT[J]_f.indd 4 1/12/11 4:47:38 PM1/12/11 4:47:38 PM

5ENGLISH

Caution:

• Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type.

• Battery shall not be exposed to excessive heat

such as sunshine, fire, or the like.

Warning (to prevent accidents and

damage):

• Do not install any battery other than CR2025

or its equivalent.

• Do not leave the remote controller in a place

(such as dashboards) exposed to direct

sunlight for a long time.

• Store the battery in a place where children

cannot reach.

• Do not recharge, short, disassemble, heat the

battery, or dispose of it in a fire.

• Do not leave the battery with other metallic

materials.

• Do not poke the battery with tweezers or

similar tools.

• Wrap the battery with tape and insulate when

throwing away or saving it.

Preparing the remote controller

About discs

When you use the remote controller for the first

time, pull out the insulation sheet.

For USA-California Only:

This product contains a CR Coin Cell Lithium

Battery which contains Perchlorate Material—

special handling may apply. See www.dtsc.

ca.gov/hazardouswaste/perchlorate

If the effectiveness of the remote controller

decreases, replace the battery.

Replacing the lithium coin battery

This unit is equipped with the steering wheel

remote control function.

• For details, refer also to the instructions

supplied with the remote adapter.

Insulation sheet

This unit can only play the CDs with:

Discs that cannot be used:

• Discs that are not round.

• Discs with coloring on the recording surface

or discs that are dirty.

• You cannot play a Recordable/ReWritable

disc that has not been finalized. (For the

finalization process refer to your disc writing

software, and your disc recorder instruction

manual.)

• 3-inch CD cannot be used. Attempt to insert

using an adapter can cause malfunction.

Handling discs:

• Do not touch the recording surface of the

disc.

• Do not stick tape etc. on the disc, or use a disc

with tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move

outward.

• Clean the disc with a dry silicon or soft cloth.

Do not use any solvents.

• When removing discs from this unit, pull them

out horizontally.

• Remove the rims from the center hole and

disc edge before inserting a disc.

EN02-29_KD-R728BT[J]_f.indd 5EN02-29_KD-R728BT[J]_f.indd 5 1/12/11 4:47:39 PM1/12/11 4:47:39 PM

6ENGLISH

Basic operations

Control dial Ejects the disc

Loading slot

Remote sensor

• DO NOT expose to

bright sunlight.

Display window

AUX (auxiliary) input jack

Detaches the panel

When you press or hold the following button(s)...

Main unit Remote

controller General operation

/SOURCE

—• Turns on.

• Turns off [Hold].

SOURCE Selects the available sources (if the power is turned on).

• If the source is ready, playback also starts.

Control dial

(turn)

VOL – / + Adjusts the volume level.

— Selects items.

Control dial

(press)

Mutes the sound or pauses during playback.

• Press the button again to cancel muting or resume playback.

— Confirms selection.

EQ SOUND

Selects the sound mode.

• Hold the EQ button on the main unit to enter tone level adjustment

directly. (page 22)

—

• Enters “Hands-Free” screen or answers incoming call when the unit

rings. (page 13, 15)

• Ends a call [Hold].

BACK —• Selects the controlling terminal of an iPod/iPhone [Hold]. (page 18)

• Returns to the previous menu.

DISP —• Changes the display information.

• Scrolls the display information [Hold].

USB (Universal Serial

Bus) input terminal

EN02-29_KD-R728BT[J]_f.indd 6EN02-29_KD-R728BT[J]_f.indd 6 1/12/11 4:47:39 PM1/12/11 4:47:39 PM

7ENGLISH

Improving the FM reception

]

<TUNER>

]

<MONO>

]

Reception improves, but stereo effect will

be lost.

To restore the stereo effect, repeat the same

procedure to select <MONO OFF>.

Automatic presetting (FM)—

SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

While listening to a station...

]

<TUNER>

]

<SSM>

]

“SSM” flashes and local stations with the

strongest signal are searched and stored

automatically.

To preset another 6 stations, repeat the

above procedure by selecting one of the other

SSM setting ranges.

Listening to the radio

[Hold]

]

“FM” or “AM”

Ÿ• [Press] Searches for stations automatically.

• [Hold] Searches for stations manually.

“M” flashes, then press the button

repeatedly.

“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.

Continued...

[Hold]

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and

6 stations for AM.

]

Tune in to a station you want to

preset.

“PRESET MODE” flashes.

]

Selects a preset number.

Preset number flashes and “MEMORY”

appears.

Selecting a preset station

Using the remote controller

∞

: Changes the preset stations.

: [Press] Searches for stations

automatically.

[Hold] Searches for stations manually.

[Hold]

EN02-29_KD-R728BT[J]_f.indd 7EN02-29_KD-R728BT[J]_f.indd 7 1/12/11 4:47:40 PM1/12/11 4:47:40 PM

8ENGLISH

Listening to a disc

Stopping playback and ejecting

the disc

If the ejected disc is not

removed within 15 seconds, it

will automatically reload into the

loading slot.

]

Turns on the power.

Playback starts automatically.

All tracks will be played repeatedly until you change the

source or eject the disc.

]

“FM” or “AM”

]

Shows the title entry screen.

]

Selects a character (A to Z, 0 to 9, —,

/, <, >) or a space, then move to the next

(or previous) character position.

4Repeat step 3until you have finished

entering the title.

To erase the entire title, press and hold DISP

after step 2, then press the control dial.

Changing the display information

Station name*

Frequency

Clock

(back to the beginning)

If no title is assigned to a station, “NO NAME”

appears for a few seconds.

[Hold]

Title assignment

You can assign titles up to 30 station frequencies (FM and AM) using 8 characters (maximum) for

each title.

• If you try to assign titles to more than 30 station frequencies, “NAME FULL” appears. Delete

unwanted titles before assignment.

Basic operations

Selects folder of the MP3/WMA.

[Press] Selects track.

[Hold] Fast-forwards or

reverses the track.

EN02-29_KD-R728BT[J]_f.indd 8EN02-29_KD-R728BT[J]_f.indd 8 1/12/11 4:47:40 PM1/12/11 4:47:40 PM

9ENGLISH

Using the remote controller

∞

: Selects folder of the MP3/WMA.

: [Press] Selects track.

[Hold] Fast-forwards or reverses the

track.

Selecting a track/folder from the

list

• If the MP3/WMA disc contains many tracks,

you can fast search (±10, ±100, ±1 000)

through the disc by turning the control dial

quickly.

• To return to the previous menu, press BACK.

For MP3/WMA disc, you can also use the search

menu (A to Z, 0 to 9, and OTHERS) to scroll

through the list menu.

• “OTHERS” appears if the 1st character is not

A to Z, or 0 to 9, such as #, —, !, and etc.

While in list menu....

Press

∞

to show the search menu.

The first character of the current folder/file

name appears.

Press

∞

to select your desired

character. Then press the control dial to

confirm.

The track list with the selected character

appears.

Turn the control dial to select your

desired track. Then press the control dial

to confirm.

• Only the existing characters will be shown on

the search menu.

• Press and hold

∞

to continuously change

the character of the search menu.

• If your disc contains many tracks, searching

take some time.

Selecting the playback modes

You can use only one of the following playback

modes at a time.

]

“REPEAT”

“RANDOM”

REPEAT

TRACK RPT : Repeats current track

FOLDER RPT : Repeats current folder

RANDOM

FOLDER RND : Randomly plays all tracks of

current folder, then tracks of next folders

ALL RND : Randomly plays all tracks

To cancel repeat play or random play, select

“RPT OFF” or “RND OFF.”

Changing the display information

Disc title/Album name/performer (folder

name)*

Track title (file name)*

Current

track number with the elapsed playing time

Current track number with the clock time

(back to the beginning)

“NO NAME” appears for conventional CDs or if not

recorded.

[Hold]

EN02-29_KD-R728BT[J]_f.indd 9EN02-29_KD-R728BT[J]_f.indd 9 1/12/11 4:47:40 PM1/12/11 4:47:40 PM

10 ENGLISH

This unit is equipped with two USB input terminals (on the control panel and USB cable from the

rear of the unit). You can use these two terminals at the same time.

You can operate the USB device in the same way you operate the files on a disc. (page 8, 9)

• This unit can play MP3/ WMA/ WAV files stored in a USB mass storage class device (such as a USB

memory, Digital Audio Player, etc.).

]

Turns on the power.

All tracks will be played repeatedly until you change the source or disconnect the USB device.

Listening to a USB device

USB cable (not supplied)

USB input terminal

USB cable from the

rear of the unit

Cautions:

• Make sure all important data has been backed

up.

• You cannot connect a computer or portable

HDD to the USB input terminal of the unit.

• Avoid using the USB device if it might hinder

your safety driving.

• Electrostatic shock at connecting a USB device

may cause abnormal playback of the device.

In this case, disconnect the USB device then

reset this unit and the USB device.

• Do not leave a USB device in the car, expose

to direct sunlight, or high temperature to

avoid deformation or cause damages to the

device.

• This unit may not play back files in a USB

device properly when using a USB extension

cord.

• USB devices equipped with special functions

such as data security functions cannot be

used with the unit.

• When connecting a USB cable, use the

USB 2.0 cable.

• Do not use a USB device with 2 or more

partitions.

• Depending on the shape of the USB devices

and connection ports, some USB devices may

not be attached properly or the connection

might be loose.

• This unit cannot recognize a USB device

whose rating is other than 5 V and exceeds

1 A.

• Do not pull out and attach the USB device

repeatedly while “READING” is shown on the

display.

• This unit may not recognize a memory card

inserted into the USB card reader.

• Connect only one USB device to the unit at a

time. Do not use a USB hub.

• Operation and power supply may not work as

intended for some USB devices.

• For additional information, see page 25.

and/or

EN02-29_KD-R728BT[J]_f.indd 10EN02-29_KD-R728BT[J]_f.indd 10 1/12/11 4:47:41 PM1/12/11 4:47:41 PM

Andere Handbücher für KD-R728BT

Inhaltsverzeichnis

Sprachen:

Andere JVC Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung